Displayit 10' Graffiti Backlit Display Kit GB10G Assembly Instructions

10’ Graffiti Backlit Kit GB10G
Assembly Instructions
Frame Lock
3-piece channel bar
Snap
Adjustable Feet
1. Set the frame standing on end. Grasp
two of the middle hubs (circled in orange)
and gently expand the frame. Note the
location of the adjustable feet for future
reference.
2. Snap all frame locks (marked in
red in the diagrams below) to
secure the frame.
3. Unfold and slip together each
bungeed channel bar.
It is recommended to assemble the
frame with it laying on its back.
30 Inch Frame (Qty 2)
10 Foot Frame (Qty 1)
3-piece channel bars
4-piece channel bars
3-piece channel bars
1-piece channel bars
Corner Hub
Slot
Thinner Edge
Nub
4A. Slide one end of the first channel bar 4B. Snap the slots in the back of the
onto the connection point of one of the channel bar onto the nubs on the hubs.
corner hubs. The triangular channel bar’s
thinner edge goes toward the inside of
the frame.
4C. Attach the other end of the channel
bar to the other corner hub. Repeat steps
4A-4C for all channel bars as seen in the
diagrams above.
1
10’ Graffiti Backlit Kit GB10G
Assembly Instructions
Endcap
Channel Bar
Fra
m
eS
id
m
Fra
e
eB
ot
to
m
Adjustable
Foot
Adjustable Foot
6. Carefully stand the frame up with the
adjustable feet on the floor.
Note: This may require two people.
5. Snap four endcap channel bars onto the
sides of the frame.
7. If the frame is on an uneven floor
or if it leans, adjust the bottom feet.
8. Snap a light bar onto the center of the “X” located
at the top of the frame.
Top Frame “X”
9. Connect the coiled end of the wire to the light bar.
Light Bar
Coiled Wire
10. Snap another light bar onto the center of the “X”
located at the bottom of the frame.
Wire To Top Light
11A. Connect the male end of wire split to the light bar.
11B. Connect the power supply to the female end of the
wire split. Plug in the power supply to test.
Light Bar
12. Repeat steps 8-11 to install a light bar onto each “X”
on the top and bottom of the frame.
Bottom Frame “X”
Wire Split Power Supply
Back
SEG
Channel
Stitched edge
goes in first
Fabric
Reflector
Start in
the corner
SEG
groove
Back of the Frame
13A. Install the back fabric reflector. Begin by tucking the corners and midway across the top
and bottom. The stitched edge of the silicone goes into the SEG channel first.
13B. Complete installation of the fabric.
2
10’ Graffiti Backlit Kit GB10G
Assembly Instructions
Graphic Installation Instructions
Caution! Installing silicone-edged graphics is techniqe sensitive; Practice will
shorten installation time.
Handle graphics with care with clean hands in a
clean environment. Clean cloth or latex gloves are
recommended.
Stitched edge
goes in first
SEG
groove
Start in
the corner
How to Install SEG Graphics:
Turn and tuck the side of the graphic with the silicone welt into the SEG groove. The
stitched ege goes into the groove first.
INCORRECT
Pull
CORRECT
Silicone
Bulge
Press While
Sliding Hand
Tuck
Pulling on the silicone welt during installation stretches the silicone and creates a
bulge in the silicone welt that is difficult to correct smoothly.
Tuck
Tuck
A series of tucks reduces excess silicone.
Installing Fabric Graphics with Endcaps
A
G
D
B
D
C
G
E
F
G
E
F
A. Tuck the graphic into left/upper endcap SEG channel
and partially down the vertical channel bar.
B. Holding the graphic off of the ground, tuck the
center of the graphic on the front of the frame.
C. Tuck the graphic into the right endcap.
E
D. Complete installation of the top
edge of the graphic.
E. Tuck the bottom/front corners and
the middle of the bottom/front.
F. Complete installation on the
bottom/front.
G. Complete installation of both
endcaps.
G
3
10’ Graffiti Backlit Kit GB10G
Assembly Instructions
90 Degree Frame Clamp Installation
Top View
Clamps will pass through
holes in the backwall graphic
Channel Bar Angle
1. To connect the 90 Degree Inside
Connector turn the knob CLOCKWISE to
loosen the sliding hook. Align the angled
portion with the angled side of the
channel bar (see green lines)
2. Snap the connector onto the frames.
Make sure the hooks on both ends go
around both channel bars.
3. Tighten connector by rotating the knob
COUNTER-CLOCKWISE.
Shown with optional counter
4
">