20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Frame Lock
3-piece channel bar
Snap
Adjustable Feet
1. Set one frame standing on end. Grasp
two of the middle hubs (circled in orange)
and gently expand the frame. Note the
location of the adjustable feet for future
reference.
2. Snap all frame locks (marked in
red in the diagrams below) to
secure the frame.
It is recommended to assemble the
frame with it laying on its back.
Left 10 Foot Flat Frame
Right 10 Foot Flat Frame
4-piece channel bars (front & back)
4-piece channel bars (front & back)
rs
ba
el
nn )
ha back
ec
iec nt &
3-p (fro
3-p
ar
ar
b
el
nn
ha )
e c ack
iec on b
(
b
el
nn
ha )
e c ack
iec on b
(
3-p
rs
ba
el
nn )
ha back
ec
iec nt &
3-p (fro
Adjustable Feet
3. Unfold and slip together each
bungeed channel bar.
Adjustable Feet
4-piece channel bars (front & back)
4-piece channel bars (front & back)
Do not attach front vertical channel bars in the middle of the 20’ display
Corner Hub
Slot
Thinner Edge
Nub
4A. Slide one end of the first channel bar 4B. Snap the slots in the back of the
onto the connection point of one of the channel bar onto the nubs on the hubs.
corner hubs. The triangular channel bar’s
thinner edge goes toward the inside of
the frame.
4C. Attach the other end of the channel
bar to the other corner hub. Repeat steps
4A-4C for all channel bars as seen in the
diagrams above.
5. Repeat steps 1-4C for the second frame.
1
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Right Frame
Left Frame
Adjustable
Foot
6A. Carefully stand each frame up with the adjustable feet on the floor.
Note: This may require two people.
7. If the frame is on an uneven floor
or if it leans, adjust the bottom feet.
6B. Slide the two frames together.
8. Snap four endcap channel
bars to the top and bottom
outer sides of the frames.
Snap Clip
Back
SEG
Channel
Back
Fabric
Back of One Frame
Hubs
9. Secure the frames together with 8 snap clips.
Snap each clip onto the poles about 6-7”away from the hubs.
Slide the clip toward the hubs to secure.
10. Install the back fabric onto each frame.
See SEG fabric installation details on page 4.
2
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Edge Lighting Installation Instructions
11. Snap a light bar onto the center of the “X” located
at the top of the frame.
Top Frame “X”
12. Connect the coiled end of the wire to the light bar.
Light Bar
Coiled Wire
Wire To Top Light
13. Snap another light bar onto the center of the “X”
located at the bottom of the frame.
14A. Connect the male end of wire split to the light bar.
14B. Connect the power supply to the female end of the
wire split. Plug in the power supply to test.
Light Bar
15. Repeat steps 8-11 to install a light bar onto each “X”
on the top and bottom of the frame.
Bottom Frame “X”
Wire Split Power Supply
3
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Silicone Edge Graphic (SEG) Fabric Installation Instructions
Caution! Installing silicone-edged graphics is techniqe sensitive; Practice will
shorten installation time.
Handle graphics with care with clean hands in a
clean environment. Clean cloth or latex gloves are
recommended.
Stitched edge
goes in first
SEG
groove
Start in
the corner
How to Install SEG Graphics:
Turn and tuck the side of the graphic with the silicone welt into the SEG groove. The
stitched ege goes into the groove first.
INCORRECT
Pull
CORRECT
Silicone
Bulge
Press While
Sliding Hand
Tuck
Pulling on the silicone welt during installation stretches the silicone and creates a
bulge in the silicone welt that is difficult to correct smoothly.
Tuck
Tuck
A series of tucks reduces excess silicone.
Installing Graphics with Wrap-Around Endcaps
1. Start tucking the graphic in one corner.
If your graphic has endcaps, start tucking
where the silicone welt begins.
2. Tuck the graphic in several places across the top channel bar.
Note: The silicone will be notched at the seam between frames. Locate
the notches and make sure they are aligned with the seams.
4. Complete installation.
3. Tuck bottom corners and several places
across the bottom of the frame.
4
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
90 Degree Frame Clamp Installation
Top View
Clamps will pass through
holes in the backwall graphic
Channel Bar Angle
1. To connect the 90 Degree Inside
Connector turn the knob CLOCKWISE to
loosen the sliding hook. Align the angled
portion with the angled side of the
channel bar (see green lines)
2. Snap the connector onto the frames.
Make sure the hooks on both ends go
around both channel bars.
3. Tighten connector by rotating the knob
COUNTER-CLOCKWISE.
Frames Required
30 Inch Frame (Qty 2)
3-piece channel bars
1-piece channel bars
Shown with optional counter
5
">
