Displayit 20' Graffiti Backlit Display Kit GB20H Assembly Instructions
广告
广告
3-piece channel bar
Snap
Frame Lock
1. Set one frame standing on end. Grasp
two of the middle hubs (circled in orange)
and gently expand the frame. Note the
location of the adjustable feet for future
reference.
4A. Slide one end of the first channel bar
onto the connection point of one of the
corner hubs. The triangular channel bar’s
thinner edge goes toward the inside of
the frame.
4B. Snap the slots in the back of the
channel bar onto the nubs on the hubs.
4C. Attach the other end of the channel
bar to the other corner hub. Repeat steps
4A-4C for all channel bars as seen in the
diagrams above.
5. Repeat steps 1-4C for the second frame.
2. Snap all frame locks (marked in
red in the diagrams below) to
secure the frame.
It is recommended to assemble the
frame with it laying on its back.
3. Unfold and slip together each
bungeed channel bar.
Adjustable Feet
Adjustable Feet
Corner Hub
Thinner Edge
Slot
Nub
Right 10 Foot Flat FrameLeft 10 Foot Flat Frame
4-piece channel bars (front & back)
4-piece channel bars (front & back) 4-piece channel bars (front & back)
4-piece channel bars (front & back)
3-piece channel bars
(front & back)
3-piece channel bars
(front & back)
3-piece channel bar
(on back)
3-piece channel bar
(on back)
Adjustable Feet
Do not attach front vertical channel bars in the middle of the 20’ display
1
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Snap
Frame Lock
1. Set one frame standing on end. Grasp
two of the middle hubs (circled in orange)
and gently expand the frame. Note the
location of the adjustable feet for future
reference.
4A. Slide one end of the first channel bar
onto the connection point of one of the
corner hubs. The triangular channel bar’s
thinner edge goes toward the inside of
the frame.
4B. Snap the slots in the back of the
channel bar onto the nubs on the hubs.
4C. Attach the other end of the channel
bar to the other corner hub. Repeat steps
4A-4C for all channel bars as seen in the
diagrams above.
5. Repeat steps 1-4C for the second frame.
2. Snap all frame locks (marked in
red in the diagrams below) to
secure the frame.
It is recommended to assemble the
frame with it laying on its back.
3. Unfold and slip together each
bungeed channel bar.
Adjustable Feet
Adjustable Feet
Corner Hub
Thinner Edge
Slot
Nub
Right 10 Foot Flat FrameLeft 10 Foot Flat Frame
4-piece channel bars (front & back)
4-piece channel bars (front & back) 4-piece channel bars (front & back)
4-piece channel bars (front & back)
3-piece channel bars
(front & back)
3-piece channel bars
(front & back)
3-piece channel bar
(on back)
3-piece channel bar
(on back)
Adjustable Feet
Do not attach front vertical channel bars in the middle of the 20’ display
1
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Back of One Frame
Back
Fabric
Back
SEG
Channel
6A. Carefully stand each frame up with the adjustable feet on the floor.
Note: This may require two people.
6B. Slide the two frames together.
7. If the frame is on an uneven floor
or if it leans, adjust the bottom feet.
Adjustable
Foot
Left Frame
Right Frame
9. Secure the frames together with 8 snap clips.
Snap each clip onto the poles about 6-7”away from the hubs.
Slide the clip toward the hubs to secure.
10. Install the back fabric onto each frame.
See SEG fabric installation details on page 4.
Snap Clip
Hubs
8. Snap four endcap channel
bars to the top and bottom
outer sides of the frames.
2
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Back
Fabric
Back
SEG
Channel
6A. Carefully stand each frame up with the adjustable feet on the floor.
Note: This may require two people.
6B. Slide the two frames together.
7. If the frame is on an uneven floor
or if it leans, adjust the bottom feet.
Adjustable
Foot
Left Frame
Right Frame
9. Secure the frames together with 8 snap clips.
Snap each clip onto the poles about 6-7”away from the hubs.
Slide the clip toward the hubs to secure.
10. Install the back fabric onto each frame.
See SEG fabric installation details on page 4.
Snap Clip
Hubs
8. Snap four endcap channel
bars to the top and bottom
outer sides of the frames.
2
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
Edge Lighting Installation Instructions
11. Snap a light bar onto the center of the “X” located
at the top of the frame.
12. Connect the coiled end of the wire to the light bar.
13. Snap another light bar onto the center of the “X”
located at the bottom of the frame.
14A. Connect the male end of wire split to the light bar.
14B. Connect the power supply to the female end of the
wire split. Plug in the power supply to test.
15. Repeat steps 8-11 to install a light bar onto each “X”
on the top and bottom of the frame.
Top Frame “X”
Light Bar
Light Bar
Coiled Wire
Bottom Frame “X” Power SupplyWire Split
Wire To Top Light
3
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
11. Snap a light bar onto the center of the “X” located
at the top of the frame.
12. Connect the coiled end of the wire to the light bar.
13. Snap another light bar onto the center of the “X”
located at the bottom of the frame.
14A. Connect the male end of wire split to the light bar.
14B. Connect the power supply to the female end of the
wire split. Plug in the power supply to test.
15. Repeat steps 8-11 to install a light bar onto each “X”
on the top and bottom of the frame.
Top Frame “X”
Light Bar
Light Bar
Coiled Wire
Bottom Frame “X” Power SupplyWire Split
Wire To Top Light
3
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
1. Start tucking the graphic in one corner.
If your graphic has endcaps, start tucking
where the silicone welt begins.
2. Tuck the graphic in several places across the top channel bar.
Note: The silicone will be notched at the seam between frames. Locate
the notches and make sure they are aligned with the seams.
3. Tuck bottom corners and several places
across the bottom of the frame.
4. Complete installation.
Installing Graphics with Wrap-Around Endcaps
Silicone Edge Graphic (SEG) Fabric Installation Instructions
Caution! Installing silicone-edged graphics is techniqe sensitive; Practice will
shorten installation time.
Handle graphics with care with clean hands in a
clean environment. Clean cloth or latex gloves are
recommended.
How to Install SEG Graphics:
Turn and tuck the side of the graphic with the silicone welt into the SEG groove. The
stitched ege goes into the groove first.
Stitched edge
goes in first
SEG
groove
Start in
the corner
A series of tucks reduces excess silicone.Pulling on the silicone welt during installation stretches the silicone and creates a
bulge in the silicone welt that is difficult to correct smoothly.
Tuck Tuck TuckPress While
Sliding Hand
Pull
INCORRECT CORRECT
Silicone
Bulge
4
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
If your graphic has endcaps, start tucking
where the silicone welt begins.
2. Tuck the graphic in several places across the top channel bar.
Note: The silicone will be notched at the seam between frames. Locate
the notches and make sure they are aligned with the seams.
3. Tuck bottom corners and several places
across the bottom of the frame.
4. Complete installation.
Installing Graphics with Wrap-Around Endcaps
Silicone Edge Graphic (SEG) Fabric Installation Instructions
Caution! Installing silicone-edged graphics is techniqe sensitive; Practice will
shorten installation time.
Handle graphics with care with clean hands in a
clean environment. Clean cloth or latex gloves are
recommended.
How to Install SEG Graphics:
Turn and tuck the side of the graphic with the silicone welt into the SEG groove. The
stitched ege goes into the groove first.
Stitched edge
goes in first
SEG
groove
Start in
the corner
A series of tucks reduces excess silicone.Pulling on the silicone welt during installation stretches the silicone and creates a
bulge in the silicone welt that is difficult to correct smoothly.
Tuck Tuck TuckPress While
Sliding Hand
Pull
INCORRECT CORRECT
Silicone
Bulge
4
20’ Graffiti Backlit Kit GB20H
Assembly Instructions
5
广告
相关
displayit Graffiti Plus Assembly Instructions
Backlit Display 20' Graffiti Assembly Instructions
20' Graffiti Display Assembly Instructions
Backlit Kit Graffiti GB20A Assembly Instructions
Backlit Kit Graffiti GB10G Assembly Instructions
Backlit Kit Graffiti GB10E Assembly Instructions
Backlit Kit Graffiti GB20F Assembly Instructions
Backlit Kit Graffiti GB10A Assembly Instructions
Backlit Kit Assembly Instructions Graffiti GB20B
Backlit Kit Graffiti GB10D Assembly Instructions
Graffiti Flat Display Assembly Instructions: 30 Inch, 5 Foot, 8 Foot, 10 Foot Frames
