Fisher & Paykel OPEX1 Assisted Opening Accessory Installation Guide

INTEGRATED COLUMN WITH ASSISTED OPENING ACCESSORY
REFRIGERATOR & FREEZER
RS6121S, RS6121SH, RS7621S, RS7621SH
RS4621F, RS6121F & RS7621F
REFRIGERATOR-FREEZER
RS6121W & RS7621W
WINE CABINET
RS6121V
ASSISTED OPENING ACCESSORY
OPEX1 & OPIN1EX1RSW
INSTALLATION GUIDE
NZ AU
CONTENTS
Safety and warnings
4
Appliance preparation
32
Integrated refrigerator & freezer
5
Door panel preparation — Custom panel
34
Integrated refrigerator-freezer
6
Door panel preparation — Wine cabinet only
35
Integrated wine cabinet
6
Water supply connection
37
Supplied parts
7
Power supply connection
38
Required parts
8
Single installation — Align appliance into cabinetry
39
Door panel kit
9
Install lower Assisted Opening Accessory (Refrigerator freezer models only)
40
Handle kit
10
Single installation — Secure appliance into cabinetry
42
Hinge change kit
11
Door panel installation
43
Wine display accessories
11
Toe kick installation
45
Assisted opening accessory
12
Install upper assisted opening accessory
46
Tools
12
Fit trims and grille
49
Product dimensions
13
Fit lower Assisted Opening Accessory Cover
50
Assisted Opening Accessory dimensions
14
Carbon filter installation
50
Cabinetry dimensions
15
Air flow divider installation
51
Cabinetry dimensions
16
Door covers & Trims installation
52
Cabinetry dimensions — Multiple installation
17
Top trim & hinge pocket covers installation
53
Custom Door panel dimensions — Single installation
18
Multiple installation — Appliance preparation
54
Custom Door panel dimensions — Multiple installation
19
Multiple installation — Join products
55
Toe kick dimensions
20
Multiple installation — Roll into cabinetry
56
Installation options
21
Multiple installation — Level and secure
57
Door clearance
22
Grilles installation
58
Drawer clearance
22
Multiple installation — Top trim & hinge pocket covers installation
59
Electrical and plumbing
23
Multiple installation — Install trims
60
Custom door panel install dimensions
24
Wine display for wine cabinet
61
Before installation
29
Change the door hinges (optional)
63
Cavity preparation
31
Final checklist
68
3
SAFETY AND WARNINGS
WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electrical shock or death.
• Read and follow the safety and warnings outlined
in this User guide before operating this appliance.
READ AND SAVE THIS GUIDE
WARNING!
To avoid hazard, follow these instructions carefully before Installing or using this appliance.
Please make this information available to the persons installing the appliance.
z
Assume all electrical parts are live.
z
Disconnect power supply to refrigerating appliance before servicing and installation.
z
BEFORE INSTALLATION
z
WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: panel edges may be sharp.
• Do not put fingers in the drawers when closing.
WARNING!
Tip Hazard
• This product may tip until it is fully installed.
Keep children away and take care. Failure to
follow this advice may result in injury.
• This appliance is top-heavy and must be secured
to prevent the possibility of tipping forward.
To ensure that the appliance is stable under
all loading conditions:
• The anti-tip bracket and fittings supplied must
be installed by a professional installer according
to the installation steps in this guide.
4
z
z
z
z
z
The appliance has front and rear rollers to easily move forward and backward. Do not
move the appliance sideways to avoid damaging the rollers or the floor covering/surface.
Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven
or dishwasher.
The appliance must be installed by a qualified installer, or Fisher and Paykel trained and
supported service technician to avoid faulty electrical and plumbing connections.
All connections for electrical power and grounding must comply with local codes and
ordinances and be made by licensed personnel when required.
Avoid installation of the appliance/s under a ground fault circuit interrupter (GFCI).
Ensure the appliance is installed properly. Improper installation that results in appliance
failure is not covered under the appliance warranty.
UNPACKING
z
z
z
z
z
z
z
z
The appliance is heavy and requires at least two persons to move and install.
Remove the installation kit (internal box) and trims kit (external box) while the product is
still on the pallet.
Avoid scratching the surface of your appliance when moving or installing.
Keep the appliance stable and door closed to prevent tipping over when moving to the
installation location.
Ensure the feet of the appliance are retracted before moving to the installation location.
If the appliance is damaged, contact your Fisher and Paykel dealer.
Ensure all components and accessories are complete. Refer to 'Before installation'.
Record the default Wifi password, and the model and registration numbers for future
servicing or repair of your appliance.
ELECTRICAL/PLUMBING
z
z
Alternatively, electrical and water supply connections for these appliances can be located
in an adjacent area or unit (cabinet or cupboard) that are easily accessible in case of
repair or disconnection.
Ensure an isolating switch is available if electrical connection is not accessible.
SAFETY AND WARNINGS
INTEGRATED REFRIGERATOR & FREEZER
INSTALLATION
z
z
z
z
z
z
z
z
The anti-tip bracket and fittings supplied must be fitted to the wall of the finished
enclosure to withstand a 100kg load.
Ensure that the anti-tip bracket is installed correctly to prevent the possibility of the
appliance tipping forward when the door is open.
Ensure the door of the appliance is closed when rolling into the cabinetry.
Ensure the power cord is not run over or damaged when rolling the product into
the cabinetry.
For flush installation, ensure the door panels are installed flush with cabinetry front
surface. Ensure the appliance is properly is centreed.
All four corners of the appliance must be supported firmly on the floor to eliminate any
movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting
and poor door sealing.
Use low speed, low torque setting when using a powered driver for the screws when fixing
or aligning the product.
Open the appliance door to remove the alignment brackets from both sides of the
appliance, and then re-tighten the screws.
Custom panel
z
z
z
z
If using Custom door panels, ensure they are prepared as per 'Custom door panel install
dimensions' section.
The thickness of the custom door panel can vary as long as the screws do not penetrate
beyond the full depth of the door panel, and as long as the overall weight of door panel
does not exceed the allowable weight. Refer to 'Door panel dimensions' for maximum
door panel weight of your product.
Do not place the handle holes in marked areas to avoid clashing with panel
attachment brackets.
Minimum panel thickness where screw hole is drilled must be 16mm.
Freezer, 46cm
Freezer, 61cm
Freezer, 76cm
RS4621FLJK*
& RS4621FRJK*
RS6121FLJK*
& RS6121FRJK*
RS7621FLJK*
& RS7621FRJK*
Changing the door hinge (optional)
z
Door hinges are interchangeable for each model. A hinge change kit is available and can
be purchased separately if you prefer to change from ‘right hinge door’ to ‘left hinge door’
or vice versa.
Refrigerator, 61cm
Refrigerator, 76cm
RS6121SLK*, RS6121SLHK*,
RS6121SRHK* & RS6121SRK*
RS7621SLK*, RS7621SLHK*,
RS7621SRHK* & RS7621SR*
Left or Right hinged door available for each model.
5
INTEGRATED REFRIGERATOR-FREEZER
Refrigerator-Freezer, 61cm
RS6121WLUK* & RS6121WRUK*
INTEGRATED WINE CABINET
Wine Cabinet, 61cm
RS6121V2LK* & RS6121V2RK*
Refrigerator-Freezer, 76cm
RS7621WLUK* & RS7621WRUK*
Left or Right hinged door available for each model.
6
SUPPLIED PARTS
INSTALLATION KIT (INTERNAL BOX)
TRIMS INSTALL KIT (EXTERNAL BOX)
Door panel attachment kit
Refrigerator or Freezer
#8 x 16
Mush Washer
Twin Thread
Philips Screw
Side bracket (12)
Bracket slider (12)
Side spacer
bracket (12)
Anti-tip bracket assembly
M5x12 Cross-head
screw (44)
Door panel side cover (2)
#8 x 16
Mush Washer
Twin Thread
Philips Screw
Wine Cabinet
#10x40
Pan Head
Philips Screw
Anti-tip bracket (1)
Masonry plug (5)
10-12x35mm
#10x40
crosshead
screw (5)
Pan
Head
Philips Screw
Door panel side cover (2)
Install fasteners kit
Refrigerator-Freezer
#8 x 19
Countersunk
Twin Thread
Posi Screw
Depth alignment
gauge (4)
Barbed plug (2)
#8 x 19
Countersunk
Twin Thread
Posi Screw
Miscellaneous parts
Hinge limiting pin (3)
8Gx16 Countersunk
screw (7)
Air toe kick seal (1)
Upper door panel side cover (2)
Lower door panel side cover (2)
Drawer top trim (1)
Flow divider cap (1)
7
SUPPLIED PARTS
REQUIRED PARTS
MISCELLANEOUS ITEMS (MI) PACK
STAINLESS STEEL TOE KICK PANEL
Not supplied and can be purchased separately through an authorised Fisher and Paykel dealer.
Visit fisherpaykel.com for more information.
INTEGRATED
REFRIGERATOR & FREEZER
INTEGRATED COLUMN
Standard toe kick height is 102mm for standard stainless steel
door panel.
INTEGRATED REFRIGERATOR
RS6121S, RS6121SH, RS7621SH & RS7621S
REFRIGERATOR & FREEZER
RS6121S, RS6121SH, RS7621S, RS7621SH
RS4621F, RS6121F & RS7621F
SERVICE & WARRANTY
INTEGRATED FREEZER
RS4621F, RS6121F & RS7621F
REFRIGERATOR-FREEZER
RS7621W & RS7621W
SERVICE ET GARANTIE
ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ
SERVIZIO E GARANZIA
WINE CABINET
RS6121V
SERVICE & GARANTIE
HUOLTO JA TAKUU
SERVICE OG GARANTI
保修和维修
INSTALLATION GUIDE
服務和保修
USER GUIDE
NZ AU UK IE SG HK
For Custom door panel installation, a toe kick 50 – 152mm must
be fitted and adjusted accordingly.
NZ AU UK IE EU SG HK
Installation guide
Service & Warranty
User guide
Air carbon filters (2)
#862755
An extra bottom grille is required when you use 50mm toe
kick height.
For Wine Cabinet only
You can purchase the extra bottom grille (847542P) online
at fisherpaykel.com.
Toe kick panel (1)
WATER CONNECTION KIT
INSTALL JOINER KIT
Supplied in models with Ice & Water function only
(RS6121SH, RS7621SH, RS4621F, RS6121F, RS7621F, RS7621W & RS7621W)
Used for combined installation of multiple appliances. Supplied in selected appliances only
(Freezer and Wine Cabinets). For other models, the joiner kit (AJ-RS84LR) can be purchased
separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more
information.
Water filter comes preinstalled on this product.
Joiner fastener kit
Collet locking clip (1)
6mm Stainless steel
braided hose with
7/16-24 UNS thread (1)
6.35mm Adaptor (2)
Joiner Sleeve (2)
Screw WSH M6 (1)
Flange Joiner Trim (2)
Aluminium center trim (1)
8
M6 Hex Nut (1)
Bolt M5 HEX (2)
DOOR PANEL KIT
REFRIGERATOR OR FREEZER
REFRIGERATOR-FREEZER
Custom door panel
WINE CABINET
Custom door panel
Custom door panel
The Custom door panel must leave the glass pane visible. A full
custom panel sheathing over the glass pane does not meet the
specifications of the Wine Cabinet.
#8 x 16
Mush Washer
Twin Thread
Philips Screw
#8 x 16
Mush Washer
Twin Thread
Philips Screw
#8 x 16
Mush Washer
Twin Thread
M5x12 Cross-head screw (44)
M5x12 Cross-head screw (44)
M5x12 Cross-head screw (44)
Included in Installation kit
Included in Installation kit
Included in Installation kit
#8 x 16
Mush Washer
Twin Thread
Philips Screw
#8 x 16
Mush Washer
Twin Thread
Philips Screw
#8 x 16
Mush Washer
Twin Thread
Philips Screw
Custom door panels must be supplied by the customer to match their cabinetry. Stainless steel door panels are not supplied and must be purchased separately through an authorised Fisher and Paykel dealer.
Take note of the part numbers above to ensure you are ordering the correct door panel set. Visit fisherpaykel.com for more information.
9
HANDLE KIT
CONTEMPORARY
PROFESSIONAL
Aluminium/Black square fine handle set
DESCRIPTION
REFRIGERATOR/FREEZER
WINE CABINET
AHD5-RDSF
REFRIGERATOR/FREEZER
WINE CABINET
AHP3-RDSF
RS61 REFRIGERATOR-FREEZER
AHD5RD6121W
RS61 REFRIGERATOR-FREEZER
AHP3-RD6121W
RS76 REFRIGERATOR-FREEZER
AHD5RD7621W
RS76 REFRIGERATOR-FREEZER
AHP3-RD7621W
MODEL
DESCRIPTION
REFRIGERATOR/FREEZER
WINE CABINET
AHSRDSF
RS61 REFRIGERATOR-FREEZER
AHSRD6121W
RS76 REFRIGERATOR-FREEZER
AHSRD7621W
MODEL
DESCRIPTION
REFRIGERATOR/FREEZER
WINE CABINET
AHCLRDSF
RS61 REFRIGERATOR-FREEZER
AHCLRD6121W
RS76 REFRIGERATOR-FREEZER
AHCLRD7621W
M5 x 25
Pan Head
Socket Screw
MODEL
OR
M5x25 hex screw
DESCRIPTION
M5 x 25
Pan Head
Socket Screw
M5x25 Hex screw
(4)
MODEL
OR
M5x25 hex screw
M5 x 25
Pan Head
Socket Screw
OR
M5x25 hex screw
M5 x 25
Pan Head
Socket Screw
OR
M5x25 hex screw
Square fine handle
(1)
Stainless steel round flush handle set
Round flush handle
(1)
M5x25 Hex screw
(4)
Aluminium round handle set
M5 x 25
Pan Head
Socket Screw
OR
M5x25 hex screw
M5 x 25
Pan Head
Socket Screw
OR
M5x25 hex screw
Round handle
(1)
M5x25 Hex screw
(4)
Classic handle set
M5 x 25
Pan Head
Socket Screw
OR
M5x25 hex screw
M5 x 25
Pan Head
Socket Screw
OR
M5x25 hex screw
M5x25 Hex screw
(4)
The handle kit is not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information.
For Refrigerator-Freezer models, each handle kit includes two (2x) handles for door and drawer panels, and M5x25 hex screws (8x).
10
HINGE CHANGE KIT
WINE DISPLAY ACCESSORIES
Not supplied and must be purchased separately through an authorised Fisher and Paykel dealer.
Visit fisherpaykel.com for more information. Select among the hinge change kit options below:
HINGE KIT
REFRIGERATOR OR FREEZER
WINE CABINET
REFRIGERATOR-FREEZER
48CM
61CM
76CM
61CM
61CM
76CM
848186
848188
848190
864757P
848184P
848184P
Accessories are not supplied with the appliance. A wine display kit and a label kit are sold
separately and can be purchased online at fisherpaykel.com.
Wine display kit
2x
Left to Right hinge
1x
Handle assembly (1)
848185
848187
848189
864759P
848183P
848183P
Right to Left hinge
Cradle assembly (4)
Left to Right hinge kit
BRACKET ADAPT K05 BTM RH
BRACKET ALCOVE TOP RH
POCKET HINGE TOP RH
BRACKET ADAPT K05 BTM RH
POCKET HINGE TOP RH
Top hinge pocket
RH (2)
K05 bottom adaptor*
bracket RH (1)
BRACKET ALCOVE TOP RH
Top alcove bracket
RH (2)
BRACKET ADAPT COL K05 RH
BRACKETtop
ADAPT COL
K05 RH
K05
adaptor*
BRACKET ADAPTRH
COL K05(1)
RH
bracket
Spacer (1)
BRACKET ADAPT COL K05 RH
POCKET HINGE TOP LH
Right to Left hinge kit
POCKET HINGE TOP LH
POCKET HINGE TOP RH
POCKET HINGE TOP RH
BRACKET ADAPT K05 BTM RH
BRACKET ADAPT K05 BTM RH
Wine label kit
BRACKET ADAPT K05 BTM LH
BRACKET ADAPT K05 BTM LH
BRACKET ADAPT COL K05 LH
Top hinge pocket
LH (2)
POCKET HINGE TOP LH
POCKET HINGE TOP LH
K05 bottom adaptor*
bracket LH (1)
BRACKET ADAPT K05 BTM LH
BRACKET ADAPT K05 BTM LH
Top alcove bracket
LH (2)
BRACKET ALCOVE TOP LH
BRACKET ALCOVE TOP LH
BRACKET ADAPT COL K05 LH
K05
top adaptor*
BRACKET ADAPT COL K05 LH
bracket LH (1)
BRACKET ADAPT COL K05 LH
Label (14)
Pencil (1)
BRACKET ALCOVE TOP RH
Top grille (1)
BRACKET ALCOVE TOP RH
Supplied in Hinge change kit
for Refrigerator & Freezer and
Wine Cabinet only.
*Top and bottom adaptor brackets for Wine Cabinet different from illustration.
11
ASSISTED OPENING ACCESSORY
TOOLS
Required parts
Required tools
Not supplied and must be provided by the installer.
Assisted Opening
Accessory
Power cord
Striker plate cover
Mounting bracket*
Lens cover
Striker plate
assembly
Powered driver
Flathead screwdriver
Ruler
(Used for multiple
installation)
Cross-head
screwdriver
Cutter
T20 star-head
screwdriver
(Used for changing hinge)
8mm socket wrench
13mm socket wrench
Hacksaw
(Used for joiner bolts)
(Used for drawer panel of
Refrigerator-Freezer model)
(For cutting air flow
divider to length)
Supplied tools
Spanner
*Refrigerator-Freezer models only
12
10mm spanner
M4 hex key
3mm allen key
(Used for multiple
installation)
Hand truck
PRODUCT DIMENSIONS
REFRIGERATOR OR FREEZER
C
REFRIGERATOR-FREEZER
D
A
C
B
WINE CABINET
C
D
A
A
B
H
D
B
G
F
F
E
FRONT
PROFILE
F
E
E
FRONT
PROFILE
FRONT
PROFILE
46CM
61CM
76CM
MM
MM
MM
A Minimum overall height (including door panel)
2188
2188
2188
B Height of chassis
2134
2134
2134
c Overall width
451
603
756
d Overall depth (excluding door panel)
610
610
610
e Depth of toe kick (measured from back of door panel)
73 – 102
73 – 102
73 – 102
f Height from floor to bottom of custom door/drawer panel
50 - 152
50 - 152
50 - 152
874
874
874
h Gap between door and drawer panels (Refrigerator-Freezer only)
—
3
3
PRODUCT WEIGHT (WITHOUT PACKAGING)
KG
KG
KG
Refrigerator or Freezer
101
117
134
Refrigerator-Freezer
—
142
163
Wine cabinet
—
152
—
PRODUCT DIMENSIONS
g Height from floor to top of drawer panel (Refrigerator-Freezer only)
46cm model for Freezer only. Wine Cabinet available in 61cm only.
13
ASSISTED OPENING ACCESSORY DIMENSIONS
C
J
B
Actuator
Striker Plate
Lens cover
E
PLAN
ISOMETRIC
ISOMETRIC
I
K
G
D
A
DATUM: FIXED SHELF
H
FRONT
F
M
N
PROFILE
L
PROFILE
DATUM: CENTRE OF CAVITY
ASSISTED OPENING ACCESSORY DIMENSIONS
MM
A Overall height of Assisted Opening Accessory
34
h Distance between centre of lens cover and centre of actuator*
28
b Overall depth of Assisted Opening Accessory
264
i Distance between center of lens cover and outside of main body
150
c Overall width of Assisted Opening Accessory
213
j Depth of main body
182
d Height of lens cover
28
k Depth of Striker Plate
9
e Width of lens cover
107
l Distance between lens cover and striker plate
6
f Depth of lens cover
24
m
Height of striker plate
34
g Depth of lens cover flange
3
n
Distance from base of main unit and base of striker plate
8
* Recommended for centre of actuator to be centred in appliance cavity
14
MM
CABINETRY DIMENSIONS
Spacers x2
Cavity for Assisted
Opening Accessory
D
A
Fixed
shelf
Bridge
trim
C
B
Lens
Cover
B
Assisted
Opening
Accessory
E
Cavity for appliance
EXPLODED
ISOMETRIC
EXPLODED
ISOMETRIC
PROFILE
ISOMETRIC
I
46CM
61CM
76CM
MM
MM
MM
57
57
57
b Height of lower cavity for appliance
2134
2134
2134
c Minimum overall height of cavity
2191
2191
2191
d Minimum overall depth of cavity **
635
635
635
e Overall width of cavity
457
610
762
f Minimum spacer height for Assisted Opening Accessory clearance
38
38
38
g Distance from front of cabinetry carcass to front of fixed shelf
11
11
11
h Distance from front of fixed shelf to front of bridge trim
3
3
3
i Minimum gap from door panel to cabinetry ***
2
2
2
j Minimum gap from edge of door panel to cabinetry
3
3
3
CAVITY DIMENSIONS
A Minimum height of upper cavity for Assisted Opening Accessory cabinetry assembly*
* Assumes fixed shelf thickness of 19mm
** Assumes a door panel thickness of 19mm with services placed outside of cavity
Bridge trim
J
F
A
H CRITICAL
Striker
Plate
G CRITICAL
PROFILE DETAIL
*** Gap required for push motion to activate Assisted Opening
15
CABINETRY DIMENSIONS
D
BRIDGE TRIM
Centre of Bridge Trim
Centre of Appliance cavity
D
Flush with front
of cabinetry
PLAN
A
C
B
F
F
FRONT
Bridge Trim needs to be easily removed.
E
UNFRAMED
Aligns appliance with
cabinetry
E
FRAMED
Aligns appliance with
frame of cabinetry
CAVITY DIMENSIONS
e Minimum gap from edge of door panel to cabinetry
f Minimum required finished return
*Assumes a door panel thickness of 19mm with services placed outside of cavity
MM
BRIDGE TRIM DIMENSIONS
MM
3
A Height of cutout
26
102
b Width of cutout
102
c Offset from centre of trim to centre of cutout
28
d Corner radii of cutout
16
max 5
CABINETRY DIMENSIONS — MULTIPLE INSTALLATION
DUAL INSTALL
TRIPLE INSTALL
C
C
A
A
B
B
DUAL INSTALL
107CM (46+61CM)
122CM (61+61CM)
137CM (46+61CM)
152CM (76+76CM)
MM
MM
MM
MM
A Minimum overall height of cavity
2191
2191
2191
2191
B Overall width of cavity
1067
1220
1372
1524
C Minimum overall depth of cavity*
635
635
635
635
168CM (46+61+61CM)
183CM (61+61+61CM)
198CM (61+61+76CM)
213CM (61+76+76CM)
229CM (76+76+76CM)
MM
MM
MM
MM
MM
A Minimum overall height of cavity
2191
2191
2191
2191
2191
B Overall width of cavity
1677
1829
1982
2134
2286
C Minimum overall depth of cavity*
635
635
635
635
635
CAVITY DIMENSIONS
*Assumes a door panel thickness of 19mm with services placed outside of cavity.
TRIPLE INSTALL
CAVITY DIMENSIONS
*Assumes a door panel thickness of 19mm with services placed outside of cavity.
Illustrations may differ from your purchased appliance.
17
CUSTOM DOOR PANEL DIMENSIONS — SINGLE INSTALLATION
REFRIGERATOR OR FREEZER / WINE CABINET
REFRIGERATOR-FREEZER
A
A
A
B
B
B
DOOR PANEL DIMENSIONS
A Minimum height of door panel*
C Width of door panel
C Depth of door panel**
C
C
C
46CM
61CM
76CM
MM
MM
MM
2086
2086
2086
451
603
756
min 16 – max 25
min 16 – max 25
min 16 – max 25
* Based on nominal kick height of 102mm.
D
61CM
76CM
MM
MM
A Minimum height of door panel
1311
1311
B Height of bottom drawer panel
721 – 822
721 – 822
603
756
min 16 – max 25
min 16 – max 25
61CM
76CM
KG
KG
Weight of top door panel
max 15
max 18
Weight of bottom drawer panel
max 9
max 11
DOOR PANEL DIMENSIONS
C Width of door panel
D Depth of door panel**
** Excluding handle
** Excluding handle
DOOR PANEL WEIGHT
Weight of Refrigerator or Freezer
door panel
Weight of Wine cabinet door panel
46CM
61CM
76CM
KG
KG
KG
max 20
max 25
max 30
—
max 25
—
DOOR PANEL WEIGHT
For Wine cabinet, the Custom door panel must leave the glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of this appliance.
For all models, maximum panel weight must not be exceeded.
18
Illustrations may differ from your purchased appliance.
CUSTOM DOOR PANEL DIMENSIONS — MULTIPLE INSTALLATION
DUAL INSTALL
TRIPLE INSTALL
The illustrations below are examples of custom door panels of different combinations for dual
installation. Minimum gaps of 3mm must be retained between door panel side edges and cabinetry
regardless of door panel widths.
C
C
The illustrations below are examples of custom door panels of different combinations for triple
installation. Minimum gaps of 3mm must be retained between door panel side edges and cabinetry
regardless of door panel widths.
C
C
C
C
C
C
C
A
B
DIMENSIONS
A Minimum height of door panel*
b Width of door panel
c Minimum clearance between
door panels and cabinetry
*Based on nominal kick height of 102mm
Illustrations may differ from your purchased appliance.
A
B
B
46CM
61CM
76CM
MM
MM
MM
2086
2086
2086
452
605
757
3
3
3
B
B
46CM
61CM
76CM
MM
MM
MM
A Minimum height of door panel
2086
2086
2086
b Width of door panel
454
605
757
3
3
3
DIMENSIONS
c Minimum clearance between
door panels and cabinetry
*Based on nominal kick height of 102mm
19
TOE KICK DIMENSIONS
Custom toe kick options
A
73mm – 102mm toe kick depth
measured from rear of door
panelto rear of kick panel
152mm toe kick height
102mm toe kick height
51mm toe kick height
(with extra lower grille attached)
A
A
B
B
B
SINGLE INSTALL
DUAL INSTALL
TRIPLE INSTALL
SINGLE INSTALL
46CM
61CM
76CM
MM
MM
MM
A Height of toe kick*
50 – 152
50 – 152
50 – 152
B Width of toe kick
454
606
759
92CM (46+46CM)
107CM (46+61CM)
122CM (61+61CM)
137CM (61+76CM)
152CM (76+76CM)
MM
MM
MM
MM
MM
A Height of toe kick*
50 – 152
50 – 152
50 – 152
50 – 152
50 – 152
b Width of toe kick
912
1064
1216
1368
1521
168CM (46+61+61CM)
183CM (61+61+61CM)
213CM (61+76+76CM)
229CM (76+76+76CM)
CUSTOM PANEL
DUAL INSTALL
CUSTOM PANEL
TRIPLE INSTALL
CUSTOM PANEL
MM
MM
MM
MM
A Height of toe kick*
50 – 152
50 – 152
50 – 152
50 – 152
B Width of toe kick
1674
1826
2131
2283
*Standard toe kick height is 102mm for any install options.
20
Illustrations may differ from your purchased appliance.
INSTALLATION OPTIONS
SINGLE INSTALL
WALL
MULTIPLE INSTALL
WALL
WALL
WALL
WALL
WALL
WALL
WALL
WALL
WALL
100mm
WALL
WALL
WALL
WALL
60mm
WALL
WALL
WALL
WALL
The illustrations above show acceptable installation options with reference to the door opening range and partition (optional). Be aware of clashing (circled) of doors or handles when opening at the same time.
If installing a partition between the appliances, ensure there is enough clearance to avoid doors/handles from interfering with each other when opening or closing.
If necessary, use a hinge limiting pin to restrict door opening rotation to 90°. Refer to 'Door clearance' for more information.
Illustrations may differ from your purchased appliance.
21
DOOR CLEARANCE
DRAWER CLEARANCE
These dimensions apply to Refrigerator-Freezer models only.
C
B
A
A
Wall
LIMITED INTERNAL ACCESS
FULL INTERNAL ACCESS
A
B
Insert hinge limiting pin
Before pushing the appliance into the cabinetry,
insert the supplied hinge limiting pin into the
borehole of the top and bottom door hinges.
The hinge limiting pin limits door swing to 90°.
For Refrigerator-Freezer models, the hinge
limiting pins are inserted into the boreholes of
the top and bottom hinges of top door.
DIMENSIONS
A Width of door (90° open)
measured from front of door
46CM
61CM
76CM
MM
MM
MM
508
660
813
292
356
419
B Minimum door clearance to
adjacent wall*
(115° — full internal access)
DIMENSIONS
A Maximum drawer extension when open
(including handle)*
B Maximum drawer extension when open
(excluding handle)
61CM
76CM
MM
MM
461
461
420
420
*Assumes handle depth of 41mm
C Minimum door clearance* to
adjacent wall*
(90° — reduced internal access)
22
110
110
110
Illustrations may differ from your purchased appliance.
ELECTRICAL AND PLUMBING
Recommended location for AOA electrical connection. Ensure there is a power socket for each
Assisted Opening Accessory. (Can be located either side at any height.)
C
C
A
B
D
E
Electrical connection must be
within this space if located
behind the appliance and must
not protrude from the back wall.
A
C
B
D
Alternative locations for
appliance connection at
rear of cavity.
SUPPLY AREA
MM
A Overall height of supply area
229
B Overall depth of supply area
25
C Width of notch in supply area (both sides)
13
D Height of sides of supply area (both sides)
127
POWER CORD
A Total length exiting from left side
of appliance (excluding plug)
B Total length exiting from right
ELECTRICAL SPECIFICATIONS
APPLIANCE
ASSISTED OPENING
Supply
230 VAC, 50 Hz
230 VAC, 50 Hz
Service
10 amp circuit
10 amp circuit
Socket
3-pin earthing-type
3-pin earthing-type
PLUMBING SPECIFICATIONS
APPLIANCE
Supply
12.7mm BSP Stainless steel braided hose with adaptor
Pressure
min 150kPa – max 827kPa @ 20°C
Illustrations may differ from your purchased appliance.
side of appliance (excluding plug)
c Total length exiting from rear of
Assisted Opening Accessory
WATER HOSE
d Total length exiting from left side
of appliance
e Total length exiting from right
side of appliance
46CM
61CM
76CM
MM
MM
MM
1385
1809
1733
1411
1835
1759
3000
3000
3000
46CM
61CM
76CM
MM
MM
MM
2271
2196
1733
1956
1878
1759
23
CUSTOM DOOR PANEL INSTALL DIMENSIONS
Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation, download the folder from http://thekitchentools.fisherpaykel.com.
The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
226
88
51
33
50
18x Pilot holes recommended
for bracket attachment.
(Do not penetrate front surface).
1902
276
50
784
1165
1546
50
1858
1869
2086
50
50
Do not place pilot holes for
handle attachment in marked
areas to avoid clashing with
panel attachment brackets
102
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
Floor
451 single install
452 dual install
46CM FREEZER
24
CUSTOM DOOR PANEL INSTALL DIMENSIONS
378
302
88
203
51
33
88
51
50
50
203
33
50
50
22x Pilot holes recommended
for bracket attachment.
(Do not penetrate front surface).
1546
1902
1858
50
1852
1869
1902
1858
102
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
Floor
603 single install
605 dual install
61CM REFRIGERATOR OR FREEZER
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
Floor
102
276
276
50
50
784
784
1165
1165
1546
50
1852
1869
2086
2086
50
50
Do not place pilot holes for
handle attachment in marked
areas to avoid clashing with
panel attachment brackets.
756 single install
758 dual install
76CM REFRIGERATOR OR FREEZER
25
CUSTOM DOOR PANEL INSTALL DIMENSIONS
For Wine cabinet, the Custom door panel must leave the glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of this appliance.
302
203
33
88
50
51
50
22x Pilot holes recommended
for bracket attachment.
(Do not penetrate front surface).
1902
1858
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
Floor
240
276
50
784
1165
1546
50
1852
1869
1589
2086
50
Do not place pilot holes for
handle attachment in marked
areas to avoid clashing with
panel attachment brackets.
415
603 single install
605 dual install
61CM WINE CABINET
26
CUSTOM DOOR PANEL INSTALL DIMENSIONS
Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com.
The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
302
88
203
33
10x Pilot holes recommended
for bracket attachment.
(Do not penetrate front surface).
51
50
Do not place pilot holes for
handle attachment in marked
areas to avoid clashing with
panel attachment brackets.
83
51
91
50
508
1127
1077
Cutouts in the hanging
bracket are applicable for
Fisher and Paykel handles only.
If locating a custom handle in
the shaded area shown above,
ensure handle screw heads are
countersunk into the back of the
door panel to avoid interference
with the hanging bracket.
50
50
237
479
772
771
50
1083
1311
139
88
50
33
38
302
203
1094
z
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
Floor
603 single install
605 dual install
603 single install
605 dual install
61CM REFRIGERATOR-FREEZER
61CM REFRIGERATOR-FREEZER
TOP DOOR PANEL
DRAWER PANEL
27
CUSTOM DOOR PANEL INSTALL DIMENSIONS
Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com.
z
The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
378
203
88
33
51
10x Pilot holes recommended
for bracket attachment.
(Do not penetrate front surface).
50
Ensure handle is mounted
65mm from edge of panel
to the centre — this will avoid
interference with bracket.
378
203
83
91
89
38
51
508
1127
1083
772
50
238
50
480
772
Cutouts in the hanging
bracket are applicable for
Fisher and Paykel handles only.
If locating a custom handle in
the shaded area shown above,
ensure handle screw heads are
countersunk into the back of the
door panel to avoid interference
with the hanging bracket.
50
1077
1095
1311
50
139
50
33
Toe kick height 152mm
Toe kick height 102mm
Toe kick height 51mm
Floor
756 single install
758 dual install
28
756 single install
758 dual install
76CM REFRIGERATOR-FREEZER
76CM REFRIGERATOR-FREEZER
TOP DOOR PANEL
DRAWER PANEL
BEFORE INSTALLATION
Checking your cabinetry
Check the dimensions of the cabinetry: height, width, depth, floor level, finished alcove returns. Refer to 'Cavity dimensions' for the correct measurements.
Check the recess depth between the Assisted Opening Accessory and the inside of door panel and allow a 2mm clearance between the inside of door panel and surrounding cabinetry.
Check the power supply and water connections
z
z
z
z
z
z
z
z
Ensure that there is a separate power socket for each appliance.
Ensure there is a power socket for each Assisted Opening Accessory.
Avoid sharing the power point with other appliances to prevent accidental switching off
of the appliance.
For power requirements, refer to the information on the serial plate.
Ensure your appliance is properly grounded.
Connect your appliance to an electrical supply with the fitted plug and lead.
If power connection is located behind the appliance, we recommend to install
an isolating switch to a location that is easily accessible to the user for repair
or disconnection.
Follow local codes and ordinances when installing the appliance.
Checking your appliance
Unpack your appliance following the steps printed on the packaging box. Ensure your appliance is the correct model as your order. Ensure components and install kits are complete.
Remove the trims kit from the back of
the appliance. Refer to 'Supplied parts'
— Trims install kit for parts included in
the box.
Illustrations may differ from your purchased appliance.
SNMU
L OC D
E TA R G
ETNI
1264SR
6SR ,F S1216SR
R ,F121
,F1267S m S1267SR &
sledo
EDIUG
NI
L L AT S
N O I TA
UA Z N
UE BG
48
B4619
8 1. 0 1
Remove the installation kit and
miscellaneous items kit from inside
the appliance.
29
BEFORE INSTALLATION
Removing pre-installed parts
Moving your appliance
Be careful when tilting the appliance forward/backward. Tape the door shut to prevent
opening while moving the appliance. You need at least two persons to move this appliance.
Top trim
Disengage one end of the top trim from dual lock
strips on the non-hinge side of the appliance.
Slide the top trim out from the hinge pocket of
the appliance.
Top door extrusion
Remove the brackets from the
non-hinge side of the pallet.
1
Unclip the trim caps of the top extrusion carefully
from both ends of the top of the door.
Ensure the magnet remains in place and not
damaged as this will affect the operation of
the appliance.
Top grille*
Open the door and remove hinge pocket cover using
a flat head screwdriver in the slot.
Open the water filter hatch on the bottom grille and
unscrew the #8x16 screw.
Hand truck
2
Tilt the appliance slightly forward
and insert the hand truck between
pallet and appliance.
3
Restrain the appliance with
strap and remove the remaining
brackets. Use corner posts while
strapping to avoid pinching of
side trims.
Remove the bottom grille by unscrewing the #8x16
screws from both ends of the grille.
*Top grille for Refrigerator-Freezer different from illustration.
Bottom grille
The bottom grille is detachable via magnets.
Strap
Toe kick mounting plate
Remove the screws to detach the toe kick
mounting plate.
4
Air flow divider
Remove the screw to detach the air flow divider.
Set aside all the removed parts to reuse later.
30
Tilt backward to load the appliance
onto the hand truck and set aside
the pallet.
Push the hand truck to the
installation location.
Illustrations may differ from your purchased appliance.
CAVITY PREPARATION
Anti-tip bracket
assembly kit
Attaching the anti-tip bracket
For solid wall installation
back wall
4
Anti-tip bracket (1x)
overhead
cabinetry
Masonry plug (4x)
#10x40
Pan Head
Philips Screw
#10x40
cross-head screw
(4x)
1
Drill holes suitable to the size of the
masonry plugs.
Hammer 10x30mm masonry plugs into
wall until flush. Fix bracket to wall with
#10x40mm cross head screws, and screw
tightly.
Measure the height (A) of the attachment
location from the floor to the alcove
return.
A
z
The height (A) must not exceed
2138mm to ensure the appliance does
not tip over during installation.
For plaster board wall
5
Tools
Fix the anti-tip bracket to the wall with
#10x40mm cross head screws, and screw
tightly with a screwdriver.
Floor
Cross-head
screwdriver
PROFILE VIEW
When rollng the appliance into the
cabinetry, ensure the anti-tip bracket
overlaps the back edge of the appliance.
z
Mark a horizontal line (B) at the back wall.
Powered drill
2
z
Located 2138mm from floor
z
Ensure there is a stud behind the wall.
The bracket must overlap the
appliance by a minimum 180mm for a
secure hold.
B
If minimum 180mm overlap cannot be
achieved, install a solid spacer to the wall
stud behind the bracket.
Pencil
3
min
197mm
Place the bracket to the backwall. Align
the undersurface of the bracket along the
marked line.
z
Be careful not to run over the power
cord when rolling in the appliance.
Mark screw hole locations, and drill screw
holes with powered drill.
bracket
Illustrations may differ from your purchased appliance.
31
APPLIANCE PREPARATION
Tools
Removing the hanging brackets
M8 hex key
M8 washer
M8 nut
Loosen the M8 screws
by 3mm.
3
13mm spanner
13mm socket wrench
1
M8 screw
Remove the M8 nut and M8
washer from the M8 screw at
the top of the door using the
supplied hex key and spanner.
3mm
For Refrigerator-Freezer:
2
32
Remove the hanging bracket
and set aside to use later.
4
Repeat steps 1 – 3 to remove
the bracket of the drawer. Use
a socket wrench to loosen the
M8 nut.
Illustrations may differ from your purchased appliance.
APPLIANCE PREPARATION
Install fasteners
kit
Attaching the barbed plugs
Before rolling into the cavity, insert a barbed plug into the
large holes at the top right and left sides of the appliance.
Barbed plugs (2x)
Cabinet depth
alignment gauge
(4x)
The plugs protect the inside surface of cabinetry from
being damaged by screws when pushing in the appliance.
Tools
Attaching the depth alignment gauges
Cross-head
screwdriver
Loosen the right and left screws at the top and bottom
sides of the door.
Locate the alignment gauges at correct orientation to the
right and left screws.
Left
Right
Place the alignment gauge by inserting the screw head
through the keyhole of the gauge.
Push the alignment gauge down to lock the position.
Tighten the screw just enough to firmly hold the gauge.
z
The alignment gauges are only temporary and must be
removed after installation.
For multiple product installation information,
refer to page 54.
Illustrations may differ from your purchased appliance.
33
DOOR PANEL PREPARATION — CUSTOM PANEL
Door handle kit
M5 x 25
Attaching the handle
Attaching the brackets
Refer to 'Custom Door panel dimensions' for correct screw hole positions on the
door panel.
Refer to 'Custom Door panel dimensions' for correct screw hole positions on the
door panel.
M5x25 hex screw
(4x)
marked line
top hanging
bracket
Door panel
attachment kit
side
bracket
For Refrigerator/Freezer/Wine cabinet
For all models
Secure the door handle to the handle
holes of door panel with M5x25 hex screw.
Side bracket
(12x)
Mark a line across the centre of the custom
door panel.
Align the ‘V’ notch at the top of the
bracket to the centreline.
Secure the top hanging bracket to the
screw holes of the refrigerator custom
door panel with M5x12 cross-head screws.
Bracket slider
(12x)
Bracket spacer
(12x)
For Refrigerator-Freezer
Secure the handle to the handle holes of
the top door panel with M5x25 hex screw.
M5x12 cross-head
screw (44x)
top hanging
bracket
side bracket
Tools
For Refrigerator-Freezer
Secure the handle to the handle holes
of the drawer door panel with M5x25
hex screw.
Powered driver
Ensure the door and drawer handles do not interfere when attaching the side
attachment brackets.
34
Illustrations may differ from your purchased appliance.
Secure the bottom hanging bracket to the
screw holes of the drawer door panel with
M5x12 cross-head screws.
Bottom
hanging
bracket
DOOR PANEL PREPARATION — WINE CABINET ONLY
Installation kit
Attaching the long glass trims
Glass trims are attached to cover the gap between the Stainless steel door panel and glass panel.
hanging bracket
Do not exceed
past this line
long trim
Long trim (2x)
long trim
red protective film
Tools
Cutter
1
Peel off a small portion of red
protective film from one end of
the long trim.
Attach the peeled portion of the trim
starting from the top of the flange on
one side of the door panel cutout.
z
2
Ensure the trim does not overlap
the hanging bracket.
Align the trim flush with inside edge
of the flange.
flange
Continue attaching the long trim for
the length of the door panel cutout,
peeling off the film as you go.
3
Cut-off the excess length of the
bottom end of the long trim.
Cut excess length of
trim along this line
Repeat all steps on the other side of
door panel cutout.
Illustrations may differ from your purchased appliance.
35
DOOR PANEL PREPARATION — WINE CABINET ONLY
Installation kit
Short trim (2x)
Attaching the short glass trims
Place the short trim along the
length of the top of door panel
cutout across the top ends of
the long trims. (A)
1
3
short
trim
Tools
Attach the peeled portion
starting from one end of flange
perpendicular to top end of
long trim.
long trim
Cutter
Continue attaching the short
trim for the length of the top of
door panel cutout, peeling off
the film as you go.
Cut both ends of the short trim
to length.
2
Peel off a small portion of
red protective film from the
short edge.
4
Ensure the trim is aligned flush
to inside edge of flange.
short
trim
short edge
long edge
long trim
Attach the remaining peeled
portion of short trim to the
flange perpendicular to top end
of the other long trim.
Repeat steps 1 – 4 to the
bottom of door panel cutout.
36
Illustrations may differ from your purchased appliance.
WATER SUPPLY CONNECTION
Water fittings kit
Connecting to water supply
Ensure the door of the appliance is closed before rolling into the cabinetry. Push the appliance carefully towards the front of the cabinetry close enough to allow access
at the back for power and water connection. Ensure an isolating tap is available if water supply is not easily accessible.
Collet locking
clip (1x)
braided hose
1
1/2 BSP Stainless
steel braided hose
with 7/16-24 UNS
thread (1x)
2
Connect one end of a braided water
hose to the water tap.
Flush water through the hose prior to
connection to the appliance to remove
any debris in the hose.
Insert the other end of the braided
hose through a hole at the rear of the
plinth and push all the way to the front
of the appliance.
Insert the tube end of the adaptor
fully into the PLV at the bottom front
of the appliance.
5
16mm Adaptor (2x)
PLV
3
Pull the hose to the front of
the appliance.
4
Connect an 6mm adaptor to
the braided hose.
6
locking clip
Secure the connection with a locking
clip between the PLV and hose end of
the adaptor.
Illustrations may differ from your purchased appliance.
37
POWER SUPPLY CONNECTION
Assisted Opening
Accessory Kit
Refrigerator / Freezer / Wine Cabinet models
Refrigerator freezer models
Bottom drawer
Run cable along top of
cabinetry.
1
1
Power cord (1)
1
Route the Assisted Opening
Accessory power cord from rear
of the product through to the
front corner. Once slack has been
removed, connect the power
cord to the Assisted Opening
Accessory unit.
Top door
Run cable along top of cabinetry.
Connect product and accessory to power supply
Refrigerator / Freezer / Wine Cabinet models and Refrigerator freezer models
At the back of your appliance, connect
the power plug to the power outlet
(220-240V, 60Hz).
z
You will hear a chime sound when
the appliance is powered on.
When powered on for the first
time, your appliance will default to
Install mode.
38
Illustrations may differ from your purchased appliance.
Once installation is complete,
unlock the control panel and
button for
hold Compartment
four seconds to start cooling.
z
Refer to your ‘User guide’ for
more information on activating
your appliance.
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY
Tools
For multiple product installation information, refer to page 54.
Pushing into the cabinetry
Cross-head
screwdriver
180mm
Ruler
Roll the appliance carefully into the cabinetry until the anti-tip bracket overlaps the
back edge of the appliance.
z
z
Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold.
Be careful not to run over the water hose and power cord when rolling in
the appliance.
Pencil
On the 'Cabinet depth alignment' side of the depth gauges, mark the step on both
sides of the door based on the thickness of the door panel.
z
Example illustration show the door panel thickness 25.4mm marked on the gauges.
Left
LLIF ON
Illustrations may differ from your purchased appliance.
LLIF ON
LLIF
LLIF ON
Right
Check if the gaps between appliance and cabinetry side walls are
even on left and right sides.
39
INSTALL LOWER ASSISTED OPENING ACCESSORY (REFRIGERATOR FREEZER MODELS ONLY)
Assisted Opening
Accessory Kit
1
Install 3 stud bolts into
the plinth as shown.
2
Connect power cord to
accessory before routing
the power cord through
strain relief bracket.
4
Snap the lower and side
tabs to remove.
5
Slot the accessory to
the stud bolts. Secure
using 3 x M5 nuts and
remove any excess slack
in the power cord.
Stud bolts (3)
Assisted opening
accessory
24" models only
M5 nuts (3)
3
40
Illustrations may differ from your purchased appliance.
Removed 2 x screws
from the front of the
flow divider and set
aside. Push flow divider
across.
24" models only
6
Push flow divider back
into place amd refit the
screws.
INSTALL STIKER PLATE
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY
Adjusting the alignment in the cabinetry
Tools
Refrigerator-Freezer
models only:
Cross-head
screwdriver
1
Open the drawer and fit the
accessory drawer bracket.
Secure using 3 screws.
Powered driver
(optional)
Front foot
adjustment
screw
Clockwise turn of the front and
rear adjustment screws raise the
height of the appliance.
Rear foot
adjustment
screw
1
Counter-clockwise turn of the
adjustment screws lower the
height of the appliance.
Foot
Turn the front and rear
adjustment screws clockwise to
extend the front feet and rear
feet until they engage the floor
and the top bracket reaches the
cabinetry ceiling.
2
Front feet
3
Rear feet
Check the depth gauges while
adjusting the screws to maintain
alignment of the appliance.
Illustrations may differ from your purchased appliance.
41
SINGLE INSTALLATION — SECURE APPLIANCE INTO CABINETRY
Install fasteners
kit
Securing the top brackets
Fix the top brackets to the ceiling surface of the
cabinetry with 8Gx16 countersunk screws.
8Gx16 Countersunk
screw (6x)
Tools
Cross-head
screwdriver
Powered driver
(optional)
Securing the side brackets
Fix the side brackets (2x) to the lower right and left sides
of the cabinetry with 8Gx16 countersunk screws.
Once the appliance is secured to the cabinetry, remove
the alignment gauges and re-tighten the side screws.
42
Illustrations may differ from your purchased appliance.
DOOR PANEL INSTALLATION
Tools
Hanging the door panel
Cross-head
screwdriver
M4 hex key (1x)
1
Hold the door panel at an angle from
the top of the door and lower the screw
holes of the hanging bracket onto the
adjustment screws. .
3
Screw the M8 washer and nut to the
adjustment screw and loosely tighten.
13mm spanner (1x)
13mm socket wrench
2
Align the door panel straight with the
door and slide-in the side brackets to the
side screws of the door,
For Refrigerator-Freezer
Tighten the side screws loosely to
temporarily secure the door panel.
Use a 13mm socket wrench to tighten or
loosen the M8 nut in the drawer panel.
Repeat steps 1 – 3 for the top door and
drawer panels.
Illustrations may differ from your purchased appliance.
43
DOOR PANEL INSTALLATION
Tools
Adjusting the height of door the panel
Adjusting the width of the door panel
Ensure the side brackets are loosely screwed when adjusting the height of the door
panel. Do not adjust the door panel height when the side brackets are screwed
tight. This can generate friction which causes the hanging brackets to bend.
Cross-head
screwdriver
Turn the adjustment screw to raise
or lower the height of the door panel
relative to the door.
Continue adjustment until gap with
cabinetry is more than 3mm.
M4 hex key (1)
z
Do not adjust the adjustment screw
higher than 1/4" (6.5mm) from its
fully down position.
To adjust the door panel further,
loosen the M8 washer and nut and
slide the door panel to suit. If further
adjustment is still required, remove the
door panel then loosen the fixing
screws of the hanging bracket and
move bracket sideways to suit.
13mm spanner (1x)
Adjust the depth of door panel
Loosen side screws on the side
brackets, and slide door panel
forward/backward.
Re-tighten once satisfied.
44
Illustrations may differ from your purchased appliance.
Once satisfied with door panel
position, fully tighten M8 washer and
nut to adjustment screw.
DOOR PANEL INSTALLATION
Tools
Installing locking bracket
TOE KICK INSTALLATION
Adjusting mounting plate brackets
Cross-head
screwdriver
Cutter
M4 hex key (1x)
REFRIGERATOR OR FREEZER / WINE CABINET
REFRIGERATOR—FREEZER
13mm spanner (1x)
Loosen the screw at the bottom
of the door, and slide the locking
bracket out until it touches the panel.
1
Refrigerator-Freezer
The locking bracket is located at the
bottom of the top door panel.
Fix the locking bracket to the door
panel with 8Gx16 countersunk screw.
2
B
3
1
2
cap screw
adjustment
brackets
Loosen the cap screws of the
adjustment brackets on both
sides of the plinth with a hex key.
Adjust the brackets to the
desired depth by moving it
forward/backward.
Re-tighten the cap screws
once satisfied.
Re-tighten the screw at the bottom
of the door.
Illustrations may differ from your purchased appliance.
45
INSTALL UPPER ASSISTED OPENING ACCESSORY
Assisted Opening
Accessory Kit
1
Measure and mark the
centre of the fixed shelf.
Align the accessory and
use to mark the position
of the rear shoulder
screws.
Remove the locating
tabs.
5
Connect power cord to
accessory before routing
the power cord through
strain relief bracket.
Shoulder screw (2)
Assisted opening
accessory
2
Using the accessory as
a guide, pre-drill 2 x
Ø3mm rear pilot holes.
Remove accessory
before securing 2 x
shoulder screws through
pilot holes.
Strain relief jacket
6
Ensure the V notch on
the striker plate aligns
with arrow on the
accessory.
7
3
Lens cover
Remove the adhesive
from the striker plate
and clip onto the
accessory.
Slot the accessory onto
the shoulder screws.
Pre-drill pilot hole at
a 45° angle using the
accessory as a guide.
8
Close the door and apply
pressure to secure. Open
the door and fit 2 x
screws to the striker plate.
Clip striker plate cover
into place.
Remove the locating
tabs.
Striker plate
Tools
4
Phillips screwdriver
46
Illustrations may differ from your purchased appliance.
fit the front screw
through the pilot
hole using a Phillips
screwdriver. Adjust
settings if required.
9
Fit accessory cabinetry
housing and slot lens
cover in place.
TOE KICK INSTALLATION
Miscellaneous
components
Attaching the mounting plate
Stainless steel toe kick
Custom toe kick
Purchased separately. Visit fisherpaykel.com for information.
Suppplied by customer to match cabinetry.
Single installation
Air toe kick seal (1x)
Stainless steel panel
Custom panel
Toe kick install kit
Toe kick panel (1x)
Dual installation
Magnets (4x)
Stainless steel panel
Custom panel
8Gx16 Mush washer
screws (4x)
#8 x 16
Mush Washer
Twin Thread
Philips Screw
Tools
1
Re-attach the toe kick mounting plate
to the plinth using same screws that
were set aside previously.
Triple installation
Cross-head
screwdriver
If toe kick depth is less than 92mm,
attach an air toe kick seal to the
mounting plate.
M4 hex key (1x)
2
Peel off the adhesive tape of air toe
kick seal and attach to the middle of
the back side of the mounting plate.
Press firmly to ensure the tape adheres
to the mounting plate.
Stainless steel panel
Custom panel
Powered driver
Illustrations may differ from your purchased appliance.
47
TOE KICK INSTALLATION
STAINLESS STEEL TOE KICK
toe kick
mounting plate
CUSTOM TOE KICK
magnet
attachment
area
toe kick
mounting plate
magnet
attachment
area
1
1
magnet fixing
location
magnet fixing
location
screws
screws
magnets
magnets
spacers
2
2
3
3
48
FIT TRIMS AND GRILLE
ATTACHING THE GRILLES
PREPARE GRILLE
Tools
Attaching the top grille
Cutter
Refrigerator or Freezer/
Wine Cabinet
Remove the section of
the grille as shown.
1
top grille
Cross-head
screwdriver
18" models only
0
2
I
Open the door, and secure
both ends of the grille and
behind the water filter hatch
with #8x16 screws.
Refrigerator-Freezer
Using a T20 bit, adjust
the screw in the centre
of the top hinge until it
reaches the 0 position.
top grille
Reattach the top grille with
#8x16 screws.
T20 star-head
screwdriver
Attaching the bottom grille
3
Adjust the accessory
settings. Refer to page
62 for details.
Refrigerator or Freezer/
Wine Cabinet
Re-attach the bottom grille
via magnets.
bottom grille
Refrigerator-Freezer
Re-attach the bottom grille
via magnets.
bottom grille
For toe kick heights 114 – 127mm, shorten the bottom grille by cutting along the
vertical ribs.
Illustrations may differ from your purchased appliance.
49
FIT LOWER ASSISTED OPENING ACCESSORY COVER
CARBON FILTER INSTALLATION
The carbon filter is used for Wine Cabinet models only, Ensure the cover is completely closed
to prevent hatch or filter from being damaged. Replacement filters (862755) can be purchased
online from fisherpaykel.com or by calling Fisher & Paykel Customer Care.
1
Slot the cover into place.
1
Remove the packaging of the filter.
Push-open latch
Open the cover of filter housing by
pushing the latch.
2
Housing
50
Illustrations may differ from your purchased appliance.
3
Insert the carbon filter in the hatch.
4
Push the filter gently into the hatch until
flush, and then close the cover until it
locks to the latch.
AIR FLOW DIVIDER INSTALLATION
The air flow divider blocks the air flow from
bypassing the front of the bottom grille.
REFRIGERATOR & FREEZER / WINE CABINET
1
REFRIGERATOR—FREEZER
Remove the adhesive layer off the air
flow divider.
Press the flow divider firmly against the
bottom of the door/drawer panel.
2
Ensure the adhesive layer side of the
divider contacts the door panel.
Secure the air flow divider to the panel
with screw.
3
Attach a flow divider cap to the flow
divider.
Illustrations may differ from your purchased appliance.
51
DOOR COVERS & TRIMS INSTALLATION
Trims install kit
Re-installing the top cover (for all models)
Remove the backing film of dual adhesive strips pre-attached to the top of the door. Ensure the magnet is in place before installing the top cover.
trim cap
notch
Top door panel side
extrusion (2x)
Bottom drawer panel
side extrusion (2x)
top cover
Press down both ends of the top
cover to engage the trim caps on
the adhesive strips.
Align the top cover to
the top of the door.
1
magnet housing
trim cap
Clip the notch into the
magnet housing, and the
trim caps on top of the
adhesive strips.
2
Ensure the magnet remains
in place and not damaged as
this will affect the operation of
the appliance.
Bottom drawer
top trim (1x)
Installing the door side covers
Refrigerator, freezer and wine cabinet
1
2
52
Illustrations may differ from your purchased appliance.
Refrigerator-freezer
Insert door side covers into the
gaps on the right and left sides of
the drawer and slide downwards
to clip into place. Press firmly
to secure.
1
Insert the drawer side covers into
the panel gaps on the right and
left sides of the drawer.
Ensure the cabinet is centered
to prevent the side covers from
interfering with the cabinet.
2
Align top trim to drawer and
press down firmly to secure
within panel bracket clips.
3
Ensure top trim is aligned with
the drawer side covers.
Ensure side cover is aligned with
the top door panel extrusion.
TOP TRIM & HINGE POCKET COVERS INSTALLATION
installing the top trim (for all models)
Slide one end of the top trim into the hinge pocket
of the appliance.
top trim
Press the other end to engage the dual lock strips
on the non-hinge side of the appliance.
installing the hinge pocket covers (for all models)
Follow the steps below to install the covers for the top, bottom or middle hinge pockets.
1
Place the hinge pocket cover to the hinge pocket,
matching the studs on the cover to the slots in the
hinge pocket.
2
Slide the cover inside the pocket.
3
Press the pocket cover to ensure the cover clips
into the pocket.
Your Integrated Installation is now complete!
Illustrations may differ from your purchased appliance.
53
MULTIPLE INSTALLATION — APPLIANCE PREPARATION
Install fasteners
kit
Attach barbed plugs and depth alignment gauges
Add flange joiner
barbed plugs
Barbed plugs (2)
Cabinet depth
alignment gauges
(4)
Remove bolts
from the locations
marked via the
green labels on your
appliance. Add the
flange joiners, and
tighten using a 3mm
Allen key to secure.
depth gauges
locations
1
Insert the barbed plugs into large holes
on the top right and left sides of both
appliances.
The plugs protect the inside surface
of cabinetry from being damaged by
screws when pushing in the appliance.
Flange joiners (2)
Tools
2
Cross-head
screwdriver
Loosen the right and left screws at the
top and bottom sides of the door.
Locate the alignment gauges at correct
orientation to the right and left screws.
Remove alcove trims
between adjacent
products.
Left
Powered driver
(optional)
Right
Place the alignment gauge by inserting
the screw head through the keyhole of
the gauge.
Push the alignment gauge down to lock
the position.
3mm Allen key
3
Tighten the screw just enough to firmly
hold the gauge.
z
54
Remove alcove trims
Illustrations may differ from your purchased appliance.
The alignment gauges are only
temporary and must be removed
after installation.
MULTIPLE INSTALLATION — JOIN PRODUCTS
Joiner fastener kit
Fit lower joiner bracket
Fit upper joiner bracket
Joiner Sleeve (2)
1
Carefully roll both products halfway
into cabinetry.
Bolt M5 HEX (2)
1
M6 Hex Nut (1)
Clamp the upper brackets together
by fitting the first the supplied
M5 bolt and joiner sleeve. Tighten
using a 8mm socket and Phillips
screwdriver until the sleeve
sits flush.
Take note of the upper and lower
joiner locations illustrated.
Handle to handle installations:
Fit the second supplied M5 bolt
and joiner sleeve.
Screw WSH M6 (1)
2
For handle to handle install, use
two bolts from both sides.
For handle to hinge, only one joiner
bolt from handle side be inserted.
2
Clamp the lower brackets together
using the supplied M6 screw and
Nut. Secure using a 4mm Allen key
and 10mm spanner.
Ensure brackets are clamped tightly
before proceeding.
3
Ensure the flange joiners contact
the adjacent product as shown.
Illustrations may differ from your purchased appliance.
55
MULTIPLE INSTALLATION — ROLL INTO CABINETRY
Tools
Pushing into the cabinetry and aligning the depth gauges
Ruler
adjacent cabinetry
1 Carefully roll both products into cabinetry.
2 Mark the step of depth gauge on the cabinetry
sides of the doors based on the thickness
of door panel.
depth gauge
56
Illustrations may differ from your purchased appliance.
Align the marked line flush with the front
surface of the adjacent cabinetry.
MULTIPLE INSTALLATION — LEVEL AND SECURE
Install fasteners kit
Adjusting alignment of appliance in cabinetry
8Gx16 Countersunk
screw (6)
Tools
1
Rear foot
adjustment
screw
Front foot
adjustment
screw
Securing the top brackets
Turn the front and rear
adjustment screws clockwise to
raise height of the appliances
and counter-clockwise to lower
the height.
Foot
Left top bracket
Right top bracket
Cross-head
screwdriver
Fix the left and right top
brackets to the ceiling
surface of the cabinetry with
8Gx16 countersunk screws.
1
Powered driver
(optional)
Rear foot
2
Beginning with the outside feet,
turn the right hand screw to
adjust the rear of the product
followed by the lefthand screw
to adjust the front. Once product
is set in cavity, adjust the
central feet.
Ensure feet engage with the floor
and the upper bracket touches
the alcove.
Ruler
Securing the side brackets
Fix one lower side
bracket to the cabinetry
side surface with 8Gx16
countersunk screws.
2
Front foot
Left lower side bracket
ruler
3
Check the alignment gauges
while adjusting the screws
to maintain the alignment
of the appliance.
Using a ruler, check if the gaps
between appliance and cabinetry
side wall are even.
Illustrations may differ from your purchased appliance.
57
GRILLES INSTALLATION
Tools
Attaching the top grille
Cutter
Refrigerator or Freezer/
Wine Cabinet
Open the door, and secure
both ends of the grille and
behind the water filter hatch
with #8x16 screws.
Cross-head
screwdriver
Refrigerator-Freezer
Reattach the top grille
with #8x16 screws.
Attaching the bottom grille
Refrigerator or Freezer/
Wine Cabinet
Re-attach the bottom
grille via magnets.
Refrigerator-Freezer
Re-attach the bottom
grille via magnets.
bottom grille
bottom grille
For toe kick heights 114 – 127mm, shorten the bottom grille by cutting along the vertical ribs.
58
Illustrations may differ from your purchased appliance.
MULTIPLE INSTALLATION — TOP TRIM & HINGE POCKET COVERS INSTALLATION
installing the top trim (for all models)
top trim
Slide one end of the top trim into the hinge pocket
of the appliance.
Press the other end to engage the dual lock strips
on the non-hinge side of the appliance.
installing the hinge pocket covers (for all models)
Follow the steps below to install the covers for the top, bottom or middle hinge pockets.
1
Place the hinge pocket cover to the hinge pocket,
matching the studs on the cover to the slots in the
hinge pocket.
2
Slide the cover inside the pocket.
3
Press the pocket cover to ensure the cover clips
into the pocket.
Your Integrated Installation is now complete!
Illustrations may differ from your purchased appliance.
59
MULTIPLE INSTALLATION — INSTALL TRIMS
Tools
Install the centre trim
Aluminium centre
trim (1x)
1
Position centre trim
between products.
3
Push trim into the
lower bracket.
2
Push trim up into the
upper bracket.
4
Press the centre trim to
fix the position.
centre trim
60
WINE DISPLAY FOR WINE CABINET
Handle assembly
Cradle assembly
Retainer blocks are pre-assembled at the bottom of both ends of the handle.
A retainer block is pre-assembled at the bottom of each cradle. Use a spacer to correctly
position the cradle and avoid wine bottles being too upright resulting in bottles tipping over.
1
Loosen the screws until the
retainer blocks can be inserted
between slats of display rack.
2
Align handle to the front end of
display rack.
3
Rotate retainer block to lock
position and tighten screw to lock
handle in place.
3
1
Write the name or type of
wine on the label.
3
2
Fit label over front edge of rack
to match displayed wine.
1
2
Insert retainer block at desired
location between slats of display
rack. Do not tighten.
Place ‘cradle guide’ on the slats
behind the handle..
Align cradle on spacer based on
size and type of wine bottle.
Rotate the retainer block to lock
position, and tighten screw.
Remove cradle guide from the rack
after use.
Wine label kit
Wipe the labels with a damp cloth
to erase.
61
TEST ASSISTED OPENING ACCESSORY
ADJUST MODE
TEST
The MODE dial can be used to adjust the overall use settings of your Assisted Opening
Accessory.
Push door
MODE
DESCRIPTION
Push the door to open slightly. The door will
remain ajar for four seconds.
1 - DEACTIVATED
Prevents the Assisted Opening Accessory from operating during
installation. Your Accessory will not operate if left in this setting.
Pull door to open fully. If left ajar, the door will
automatically close again after four seconds.
2 - SMALL OPENING
Sets the opening distance to its minimum.*
3 & 4 - LARGE OPENING
Sets the opening distance to its maximum.*
5 - DRAWER
Sets the opening distance to its maximum.* Recommended for all
drawer installations.
Push handle
If handles are fitted, gently push the handle
then pull to open slightly. The door will remain
ajar for four seconds.
Rotate the dial using a flat-bladed
screwdriver until the desired setting
is selected.
ADJUST SENSITIVITY
Sensitivity
The SENSITIVITY dial can be used to adjust the push/pull sensitivity of your Assisted Opening
Accessory. The sensitivity cannot be adjusted on DishDrawer™ installations.
Rotate the dial using a flat-bladed
screwdriver until the desired setting
is selected.
Setting 1 is the least sensitive and 5 is
the most sensitive.
*Opening distance will vary depending on custom panel thickness and the position of the
Assisted Opening Accessory in the cavity.
62
Pull door to open fully. If left ajar, the door will
automatically close again after four seconds.
CHANGE THE DOOR HINGES (OPTIONAL)
You have the option to switch the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation, and must
be purchased separately. Ensure that you remove all the shelves, covers and trims from the appliance before changing the hinges. Take care not to damage the door.
Detach the door
REFRIGERATOR & FREEZER / WINE CABINET
REFRIGERATOR—FREEZER
REFRIGERATOR & FREEZER / WINE CABINET
REFRIGERATOR—FREEZER
M6x10 hex screws
Top hinge
Release the hinge spring by turning the
T20 screw in the hinge to the ‘0’ position.
1
‘0’
T20 screw
Close the door and lay the appliance on
its back on the pallet.
2
Detach the door from the appliance by
unscrewing the door hinge M6x10 hex
screws (4x) at the top hinge and bottom/
middle hinge.
bottom/middle hinge
63
CHANGE THE DOOR HINGES (OPTIONAL)
Detach the top door hinge
A
b
C
E
D
f
Detach the bottom door hinge — For Refrigerator & Freezer / Wine Cabinet
1 Rotate the top hinge (A) outwards and remove the top hinge pocket cover (B)
using the flat head screwdriver in the slot of the cover.
2 Unscrew M6x16 countersunk screws (C) to remove top hinge, and set
aside to use later.
3 Unscrew M6x16 countersunk screws (D) from hinge pocket to remove hinge
pocket and top alcove bracket.
4 Unscrew M5x12 countersunk screws (E) to remove top hinge bracket and spacer.
5 For the non-hinge side, remove the top alcove bracket by unscrewing the M6x16
countersunk screws (F).
Detach the middle door hinge — For Refrigerator-Freezer
a
B
d
A
C
E
F
E
Do not
remove!
1 Rotate the bottom hinge (A)
outwards and remove bottom hinge
pocket cover (B) using a flat head
screwdriver in the slot.
2 Remove the hinge by unscrewing the
M6x16 countersunk screws (2x) (C).
3 Open the water filter hatch on
the bottom grille and unscrew the
#8x16 screw (D) while holding the
grille in place.
4 Remove the bottom grille by
unscrewing the #8x16 screws (E) from
the bottom left and right of the grille.
5 Remove bottom hinge
bracket by unscrewing M6x16
countersunk screws (F).
IMPORTANT!
Do not remove plinth-to-cabinet
retention brackets!
64
B
C
1 Rotate the middle hinge (A) and
unscrew M6x16 countersunk screws (B)
to remove middle hinge, and set
aside to use later.
2 Unscrew M5x12 countersunk
screws (C) to remove top hinge
bracket and spacer.
CHANGE THE DOOR HINGES (OPTIONAL)
Move the sensor housing
1
Unclip the hall sensor
from the housing.
2
Unhook the interceptor
board harness from
sensor housing so
harness is loose.
3
Remove the #8x16
screws (2x) from the
sensor housing.
4
Move the sensor housing
to align the opposite hall
sensor clip with the centre
of the cabinet.
5
Reinstall the sensor housing
using #8x16 screws (2x)
into the pre-drilled holes in
the cabinet top panel.
6
Clip the hall sensor into
the sensor housing in
the pocket closest to the
centreline of the cabinet.
7
F
Press the harness from the
interceptor board into the
forks on the sensor housing.
65
CHANGE THE DOOR HINGES (OPTIONAL)
Re-attach the top door hinge
D
c
e
A
b
f
Re-attach the bottom door hinge — Refrigerator or Freezer / Wine Cabinet
1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk
screws (A) on the new hinge side at the other side of the appliance.
2 Install the new hinge pocket and alcove top bracket on the new hinge side using
two (2x) M6x16 countersunk screws (B).
z
The new hinge pocket and top alcove bracket are supplied with the hinge kit.
3 Install the new hinge in the new hinge pocket by screwing M6x16 countersunk
screws (2x) (C).
4 Open the hinge (D) and clip the top hinge pocket cover (E) to the
top hinge pocket.
5 Install a new top alcove bracket on the new
non-hinge side (F).
Re-attach the middle door hinge — wRefrigerator-Freezer
C
B
D
E
d
A
D
66
1 Install a new lower hinge bracket
on the new hinge side with M6x16
screws (2x) (A).
2 Ensure that the tab on the top of the
bracket inserts into the slot in the
plinth front bracket.
3 Use the hinge that was removed from
the top of the appliance and insert
the tabs into the hinge lower bracket.
Rotate the hinge into place and fix with
M5x12 countersunk screws (2x) (B).
4 Open the hinge (C), and install the new
top grille assembly.
5 Fasten in place with #8x16 screws (3x)
(D). One each at the bottom left and
right of the grille and one behind the
water filter hatch.
6 Clip the bottom hinge pocket cover to
the new hinge pocket (E).
B
C
A
1 Reinstall the middle hinge
bracket and spacer with M5x12
countersunk screws (A).
2 Open the middle hinge (B) and
reinstall the hinge with M6x16
countersunk screws (C).
CHANGE THE DOOR HINGES (OPTIONAL)
Change the top door brackets
Reinstall the door
L
A
FIL
L
FIL
M6x10 hex screws
Top hinge
ILL
NO
F
NO
F
NO
NO
1 Unscrew the M5x10 screws (4x) to
remove the top adapter bracket from
the top of the door (A).
2 Install the new top adapter bracket into
the other side of the top of the door
with M5x10 screws (4x) (B).
ILL
L
FIL
L
FIL
L
IL
OF
N
IF
LL
1 Secure the door to the top hinge and
bottom/middle hinge with M6x10
hex screws (4x).
ON
ILL
NO
F
IF
LL
b
IF
LL
IF
LL
ON
ON
use new top
adaptor bracket
Bottom/middle hinge
Change the bottom door bracket
‘I’
NO
L
IL
OF
L
FIL
1 Remove the door panel locking
bracket and washer from the bottom
of the door by unscrewing M6x25
screw (1x) (C).
2 Remove the bottom adapter bracket
and spacer from the bottom of the
door by unscrewing M6x25 screws (2x)
and M5x30 screw (1x) (D).
3 Install the new bottom adapter bracket
and existing spacer to the other side of
the door with M6x25 screws (2x) and
M5x30 screw (1x) (E).
4 Install the existing door panel locking
bracket and washer to the other side of
the door with M6x25 screw (1x) (F).
c
use new bottom
adaptor bracket
and spacer
d
e
f
IF
LL
2 Activate the hinge spring by turning the
star T20 screws to the I position.
3 Return the appliance to the
upright position, and reinstall all
covers and trims.
T20 screw
ON
LIF
L
ON
use existing
locking bracket
IF
LL
IF
LL
ON
IF
LL
ON
IF
LL
IF
LL
IF
LL
ON
ON
67
FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
All models
Cabinet Level: Ensure the appliance is level and dimensions accurate.
Refer to 'Cabinetry Dimensions', pages 15 – 17.
Anti-tip: Ensure the appliance is securely fastened to the cabinetry with the supplied
anti-tip bracket and fittings. Refer to 'Cavity preparation', page 31.
Door panel/and toe kick: Ensure door panel/s and toe kick are attached securely and
properly aligned; Refer to 'Door panel installation', pages 43 – 45, and 'Toe kick
installation', pages 45-48.
Doors closing freely: Ensure the door/drawer can open and close freely with no
resistance from surrounding cabinetry or product. Refer to 'Door clearance' and
'Drawer clearance', page 22.
Hinge pin: Ensure hinge limiting pin is fitted for 90° door swing. Refer to
'Door clearance', page 22.
Vent clearance: Ensure the cabinet installation provides the minimum vent clearance
required. Check that the gap between the bottom of the door panel and the ground
is at least 50mm. Refer to 'Product Dimensions', page 13.
Assisted Opening Accessory: Ensure unit is installed correctly and has been adjusted as
required. Refer to page 60.
Packaging: Ensure all internal and external packaging has been removed. Refer to
'Before installation', page 29.
Fault codes: Ensure no error codes are shown.
Installation mode: Ensure the Installation Mode is de-activated (hold on Compartment
button for 4 sec. Refer to 'Power supply connection'.
User guide: Check the User Guide is inside the product in a visible area for the customer.
For products with water only or Ice and water function
Ice maker: Turn ice maker ON. Force a manual ice maker cycle by pressing the (alarm
symbol), - & + buttons together for 4 seconds then close the door(s). The ice tray will
fill and empty into the bin below, dry the bin and return it correctly. Refer to page 19 of
your User Guide.
Dispenser: Ensure the water is flowing through the system using the dispenser pad.
Refer to page 18 of your User Guide.
Installation trims: Check all Installation Trims are present and fitted securely.
Door opening sensor: Ensure magnets and sensors are correctly installed by
checking that the door alarm is not beeping and that compartment lights are on
when door is opened.
Complete and keep for safe reference:
Model
Installer’s Name
Serial No.
Installer’s Signature
Purchase Date
Installation Company
Purchaser
Installation Date
Dealer Address
68
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2024. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.
592954A
11.24
">