advertisement
\
O
L
®
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG MOWER READING
THIS MANUAL CAN PROVIDE YOU WITH
ASSISTANCE IN MAINTENANCE AND AD-
JUSTMENT PROCEDURES TO KEEP YOUR
MOWER PERFORMING TO MAXIMUM EFFI-
CIENCY.
THE SPECIFIC MODELS THAT THIS
BOOK COVERS ARE CONTAINED ON THE
INSIDE COVER.
BEFORE OPERATING YOUR
MACHINE, PLEASE READ ALL THE INFOR-
MATION ENCLOSED.
{_
}{{
J
PARTNUMBER 03072
FAILURE TO FOLLOW SAFE OPERATING
PRACTICES
MAY RESULT
iN SERIOUS iNJURY.
* Keep all shields in place, especially the grass discharge chute.
* Before performing any maintenance or service, stop the machine and remove the spark plug wire and ignition key.
* if a mechanism becomes clogged, stop the engine before cleaning.
* Keep hands, feet and clothing away from power-driven parts.
* Read this manual completely as well as other manuals that came with your mower.
* Keep others off the tractor (only one person at a time)
REMEMBER -YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
Hazard control
and accident
prevention
are dependent upon the awareness, concern,
prudence,
and proper training of the personnel
involved
in the operation, transport, maintenance, and storage of the equipment.
This manual covers the operating
instructions
and illustrated parts list for:
SW32-13KA
SW36-13KA
SW36-13KH
SW36-14KA
SW48-14KA
SW48-15KH
SW48-17KA
SW48A-17KA
SW52-17KA with a serial with a serial with a serial with a serial with a serial with a serial with a serial with a serial with a serial number number number number number of 5010001 number of 5020001 to 5029999 number of 5030001 to 5039999 number of 5800001 to 5809999 number of 5040001 to 5049999 of 5050001 of 5060001 of 5070001 of 5080001 to 5019999 to 5059999 to 5069999 to 5079999 to 5089999
Always use the entire serial number listed on the serial number tag when referring to this product.
TABLE OF CONTENTS
MODEL SW
SU BJECT
Introduction ..................................................................................................
General Safety Instructions .........................................................................
Signal Words ...............................................................................................
Before Operating .........................................................................................
While Operating ...........................................................................................
Maintenance and Storage ...........................................................................
Initial Run-In Procedures .............................................................................
Mower Operation .........................................................................................
Cutter Deck Belt Adjustments ......................................................................
Transmission Drive Belt ...............................................................................
Drive Control Adjustments ...........................................................................
Cutter Deck Adjustments .............................................................................
Blade Height Adjustments ...........................................................................
Cutter Blades ...............................................................................................
Lubrication and Maintenance Chart ............................................................
Troubleshooting Cutting Conditions .............................................................
Technical Specifications ..............................................................................
PAGE
7
7
8
6
6
9 = 11
12 =13
1
2
2
3
4
1
1
4
5
5
MEMBER
I
TABLE OF CONTENTS
(CONTINUED)
SU BJECT
PAGE illustrated
Parts List
SWM-32", 36"Cutter Decks ................................................................
SWM-48", 52", 61", 72" Cutter Decks ................................................
Engine Deck .......................................................................................
Handle Assembly ................................................................................
instrument Panel ................................................................................
Peerless Transmission ........................................................................
14-15
16-17
18-19
20-21
22
23
Engine Deck Wire Harness14 Kawasaki .........................................
Wire Harness W/Relay. ......................................................................
Handle Wire Harness-Manual Start ...................................................
24
24
25
Engine Deck Wire Harness-Kohler (Single Cyl.)& 17 KA ..................
26
Replacement Decals ..........................................................................
27-29
Warranty Statement ...............................................................
Inside Back Cover
II
SCA6
INTRODUCTION
SIGNAL
WORDS
Your mower was built to the highest standards in the industry. However, the prolonged life andmaximum efficiency of your mower depends onyou following the operating, maintenance and adjustment instructions in this manual.
We encourage you to contact your dealer for repairs.
All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts.
This symbol means "Attention!
Become Alert! Your
Safety is Involved!".
The symbol is used with the following signal words to attract your attention to safety messages found on the decals and throughout this manual. The message that follows the symbol contains important information about safety. To avoid injury and possible death, carefully read the message!
Be sure to fully understandthe causes of possible injury or death.
A replacement Operator's Manual is available from your
Scag Servicing Dealer or by contacting Scag Power
Equipment, Service Department at P.O. Box 152,
Mayville, WI 53050. Please indicate the complete model and serial number of your Scag product.
SignalWord:
It is a distinctive word on safety decals and throughout this manual that alerts the viewer to the existence and relative degree of the hazard.
USE OF OTHER THAN ORIGINAL
REPLACEMENT
WARRANTY.
SCAG
PARTS WILL VOID THE
The "Right" and "Left", "Front" and "Rear" of the machine are referenced from the operator's perspective when in the normal operating position and facing the forward travel direction.
GENERAL
SAFETY iNSTRUCTiONS
The signal word "DANGER" denotes that an extremely hazardous situation exists on or near the machine that could result in high probability of death or irrepairable injury if proper precautions are not taken.
READ THIS OPERATOR'S MANUAL and instructions furnishedwith attachments.
kWARNING:
Perform only those maintenance procedures described in this manual.
If major repairs are ever needed or assistance is desired, contact an Authorized Scag
Dealer.
To ensure optimum performance and safety, always purchase genuine SCAG replacement parts and accessories.
The signal word"WARNING" denotes that a hazard exists on or near the machine that can result in injury or death if proper precautions are not taken.
i
Your safety and the safety of others depends significantly upon your knowledge and understanding of all correct operating practices and procedures of this machine.
The signal word"CAUTION" is a reminder o f safety practices on or near the machine that could result in personal injury if proper precautions are not taken.
SCA6
BEFORE OPERATING
WHILE
OPERATING
.
Know the controls and how to stop quickly.
2.
Do not allow children to operate the machine.
Do not allow adults to operate the machine without properinstruction.
.
Remove all debris or other obj ects that might be picked up and thrown by the cutter blades.
Keep all bystanders away from the mowing area.
.
Keep all shields, safety devices, and decals in place.
Ifa shield, safety device or decal is defective or damaged, repair or replace it before operating.
Also, check all nuts, bolts and screws for proper tightness, to assure the machine is in safe operating condition.
.
Do not operate the machine while wearing sandals, tennis shoes, sneakers or shorts. Also, do notwear loose fitting clothing which could get caught in movingparts.
Always wear longpants andsubstantial shoes. Wearing safety glasses and safety shoes is advisable andrequiredby some local ordinances and insurance regulations.
.
Fill the fuel tank with clean, fresh gasoline, with a minimum octanerating of 87. Avoid spilling gasoline. Gasoline is highly flammable, handle it carefully.
A. Use an approved gasoline container.
B. Do not fill the tankwhile the engine is hot or runtfing.
C. Do not smoke while handling gasoline.
D. Fill the fuel tank outdoors andup to approximately 1" (25 mm) below the bottom of the filler neck.
E.
Wipeup any spilled gasoline.
.
Before attempting to start the engine, shift the transmission into neutral, move the blade engagement switch to the OFF position, and move the neutral latches to neutral.
.
.
.
.
.
Start the engine when the neutral latches are in the neutral lock position, the cutter blades are disengaged, and the transmission is in neutral.
.
Do not run the engine in a confined area without adequate ventilation.
Exhaust fumes are hazardous and could possibly be deadly.
.
Using the machine demands attention. To prevent loss of control:
A. Mow only in daylight orwhen there is good artificiallight.
B. Watch for holes or other hidden hazards.
C. Do not drive close to a drop-off, ditch, creek bank, or other hazard.
D. Reduce speedwhen making sharp turns and when turning on hillsides.
E.
Always be sure of your footing. Keep a firm hold on the handles and walk---never run.
F.
Do not operatewhere conditions are slippery.
.
The discharge chute must always be installed and in the down position on the side discharge cutter deck except when the Scag optional grass catcher or mulchingplate areproperly installed. If the discharge area shouldplug, shut the engine off and wait for all movement to stop before removing the obstruction.
Disengage the blades and wait for them to stop before crossing gravel drives, walks or roads.
Shut the engine off and wait until the blades come to a complete stop before removing the grass catcher container.
Never raise the cutter deck while the blades are rotating.
Always park the mower and!or start the engine on a level surface.
2
SCA6
14. Use only Scag approved riding attachments.
.
If the cutting blades should strike a solid object or the equipment should start to vibrate abnormally, stop the engine, disconnect the spark plug wire, and check immediately for the cause. Vibration is generally awarning of trouble. Check the machine for damaged or defective parts. Repair any damage before starting the engine or operating the cutter deck. Be sure the blades are in good condition and the blade bolts are tight.
10. Reduce speed and exercise extreme caution on slopes and in sharp turns to prevent tipping or loss of control. Be especially cautious when changing directions on slopes.
S cag Approved Riding Attachments:
RS-2
RS-ZT
Using unapproved attachments, (especially "standup" riding attachments) may be hazardous.
MAINTENANCE AND STORAGE
.
Disconnect the spark plug wire from the spark plug to prevent accidental starting of the engine when servicing, adjusting or storing the machine.
,WARNING:
DO NOT operate on steep slopes.
To check a slope, attempt to back up it (with the cutter deck down), if the machine can back up the slope
without the wheels slipping, reduce speed and use
extreme caution.
ALWAYS FOLLOW OSHA
APPROVED OPERATION.
.
If the mower must be tipped to perform maintenance or adjustment, remove the battery, drain the gasoline from the fuel tank and the oil from the crankcase.
.
To reduce potential fire hazard, keep the engine free of excessive grease, grass, leaves and accumulations of dirt.
.
Be sure the machine is in safe operating condition by keeping nuts, bolts, and screws tight.
Check the blade mounting bolts and nuts frequently to be sure they are tightened.
11. Do not touch the engine or muffler while the engine is running or soon after it is stopped. These areas could be hot enough to cause a burn.
12. Before leaving the operator's position or leaving the mower unattended, shift thetransmission into neutral, place the neutral latches in the neutral lock position, andmove the blade engagement switch to
OFF. Shut the engine OFF and remove the key.
13. Do not pass or stand on the grass discharge side of any mower with the engine running.
Stop operation when another person approaches.
.
If the engine must be running to perform a maintenance adjustment, keep hands, feet, clothing and other parts of the body away from the cutter deck blades and other moving parts.
.
Do not overspeed the engine by changing governor settings.
To be sure of safety and accuracy, have an authorized dealer check maximum engine speed with a tachometer.
.
The engine must be shut off before checking the oil or adding oil to the crankcase.
3
.
Allow the engine to cool before storing the mower in any enclosure such as a garage or storage shed.
Make sure the fuel tank is empty if the machine is to be stored in excess of 30 days.
Do not store the mower near any open flame or where gasoline fumes may be ignited by a spark.
SCA6
9.
Always store gasoline in a safety-approved, red container.
10. Be careful when servicing the battery as it contains acid, which is corrosive and could cause burns to skin and clothing.
11. Batteries release explosive gases when being charged or discharged.
Keep batteries away from any source of sparks and/or flame.
INITIAL RUN-IN PROCEDURES
(FIRST DAY OF USE OR APPROXI-
MATELY 10 HOURS)
1. Check the belts for proper tension at 2, 4 and 8 hours. Adjust as needed.
2.
Check the steering control rods for neutral adjustment.
(See Adjustments, page 6)
.
Check the tires for proper pressure.
Caster Wheels 25 psi.
Drive Wheels 15 psi.
4.
Check for loose hardware.
Tighten as needed.
.
Check the safety switches for proper adjustment:
* The engine will crank, but not start if the machine is not in neutral.
* On electric startmachines, the enginewill not crank if the PTO switch is on.
* The engine should crank and start if the machine is in neutral andthe PTO engagement switch is OFF.
.
Apply lubricant to all the grease fittings.
Lubricant was applied at the factory.
This is just a precautionary check to make sure that all the fittings have been lubricated.
MOWER OPERATION
1.
Read and understand the safety instructions before attempting to operate this machine.
2.
Before starting the engine:
* Check the oil level in the engine.
* Fill the fuel tank with clean, fresh, lead-free gasoline.
* Open the fuel valve on the bottom of the fuel tank.
=NOTE=
Uxe gaxo/ine
with an octane rating no/exx
than
87.
* The transmission must be in NEUTRAL.
* The blade clutch switch must be in the OFF position.
* The operator's presence levers must be released.
* The neutral latches must be in the neutral lock position.
* The key switch must be on.
3.
Start the engine:
* Choke as required.
If the engine is cold, pull the choke knob out. When the engine starts, slowly push the choke in. If the engine stalls, repeat the above operation.
When the engine is warm, choking may not be necessary.
.
Engage the cutter blades by pulling the blade clutch switch into the ON position.
Push the switch to the
OFF position to disengage the cutter blades.
4 i
U U i
PUSH
DOWN TO DISENGAGE
390S0138
END OF L-SHAPED
NUT
BRACKET
\
I
"J"
BOLT
I A_f'BELT
SCA6
-NOTE-
When PTO is engaged or (possibly) disengaged, a squealing sound from
the underside of the machine is normal.
B is caused by the electric clutch plates meshing
as the cutter
blades come
up m speed.
For best equipment/ijO, engage
the
clutch with the engine
at 1/2 throttle, not under
.full load.
,WARNING:
To avoid serious bodily injury and damage to the transmission, the machine must be at a full stop before shifting between gears or shifting between forward and reverse.
J
3.
5.
Shift the transmission into gear for the desired mowing speed.
=NOTE=
Top speed is suggested
only.for
transport/
CUTTER DECK DRIVE BELT TENSION
ALIGNMENT IDLER - E.H.
Figure 1
SC400G
Adjust the RH blade drive belt using a belt tension gauge. Adjust the belt so that the belt moves 1/2" with 10 pounds of pressure.
Adjust the tension by tightening or loosening the J-bolt nut. (See figure 2
&3)
BELT
.
While squeezing the steering brake levers with both hands, release both neutral latches.
.
When the steering brake levers are released, the machine will travel straight. To make a right turn, squeeze the RH lever. To turn left, squeeze the LH lever.
WASHER
NUT
8.
TO STOP, squeeze both levers, lock the neutral latches, and shift the transmission into neutral.
CUTTER
DECK
BELT ADJUSTMENTS
1. Removethebelt cover.
.
Adjust the cutter deck drive belt using a belt tension gauge. Adjust the belt so that the belt moves 1/2" with 10 pounds of pressure.
Adjust the tension by tightening or loosening the J-bolt nut. (See figure 1)
=NOTE=
Due to initial
belt stretch and to prevent
the belt
._'om slipping,
check this" adjustment after the first
2 hours, 4 hours and 8 hours of operation.
5
Figure 2.
RH Blade Belt Adjustment
CUTTER DECK
ADJUSTMENT
IDLER
BELT TENSION
ADJUSTMENT IDLER
DISCHARGE
AREA
S
I
CHECK BLADE DRIVE
BELT TENSION HERE
Figure 3. Cutter Deck Belts
SC402G
SCA6
TRANSMiSSiON
DRIVE BELT
CUTTER
DECK
ADJUSTMENTS
Adjust the transmission drive belt so that there is about a
3/16" deflection with 10 lbs. of pressure.
Adjustby loosening idler pulley mounting bolt and sliding the idler left or right to change belt tension.
Due to the many cutting conditions that exist, it is difficult to suggest a cutter deck setting that will work for every lawn. There are two adjustments that can be made on these decks, pitch andheight.
DRIVE CONTROL ADJUSTMENTS
PITCH is the angle of the blades (comparing front to rear). A 1/4" downward pitch (front of deck down) is recommended for best cutting performance.
.
Adjust the steering control rods so that there is approximately 3/4" clearance from the bottom of the rod to the bottom of the neutral latch slot when in the drive position.
(See figure 4)
NEUTRAL
LATCH
HEIGHT is the nominal distance the blade is offofthe ground. This measurement is made with the blades pointed side to side and distance is measured between cuttingtip andground.
(Also seeBladeHeightAdjustmerit, nextpage)
NEUTRAL LOCK
POSITION
DRIVE POSITION
Changes to the cutting height can be achieved by repositioning the cutter deck (This adjustment will also effect the pitch of the deck). There are three available positions (see figure 5).
LOW CUT (1 3/4" to 3")
3/4"-
STEERING
BRAKE LEVER
SC404GB
Figure 4. Steering Control Rod Adjustment
.
Adjust the steering brake rods so that the brakes do not apply until the steering levers are pulled tight to the handles. When the steering levers are locked in the neutral position the machine should move freely.
MID RANGE
1/2" to 3 3/4")
HIGH CUT
(3 1/4" to 4 1/2")
CUTTER
DECK HEIGHT ADJUSTMENT
Figure 5. Cutting Height Adjustment
SC405G
6
SCA6
Caster spacers also can be repositioned to change cutting heights and to change the pitch of the deck. (See figure6)
PIN
SPACERS
G
REPOSITIONING
SPACERS SC406G99
Figure 6. Caster Wheel Spacers
BLADE HEIGHT
ADJUSTMENT
Adjusting the blade height can be done by moving any number of the five smaller 1/4" spacers on the blade mounting bolts to the top of the spindle shaft or below the spindle shaft.
=NOTE=
All blades should be positioned equally.
For best cut and discharge, a minimum of three spacers should be installed between the blade and the spindle.
(See figure 7)
CUTTER BLADES
Do not sharpen beyond 1/3 of the width of the blade.
(See figure 8)
=NOTE=
Dress
the blade
with a file.
Using a wheel grinder
may burn
the blade.
Check the balance
(?f the blade.
If blades
are out (?/balance,
tion and premature wear (?/spindle assembly vibracan occur.
See your authorized Stag dealer for blade balancing
or special
tools" if you choose to balance your own blades.
DO
7
Figure 7. Blade Spacers
SC407G
BLADE BACK
X MUST NOT EXCEED
1/3 BLADE
WIDTH
SC408G
Figure 8. Blade Sharpening
SCA6
LUBRICATION & MAINTENANCE
BREAK-IN I
+ Grease spindle until grease comes out the relief valve.
8 HOURS (DALLY) I
Compatible Greases:
40 HOURS (WEEKLY) I
100 HOURS (BIWEEKLY) I
Lidok EP #2 (found at industrial shops)
Ronex MP (Exxon service stations)
Shell Alvania (Shell service stations)
Mobilux #2 (Mobil service stations)
Super Lub M EP #2 (Conoco service stations)
X
X x x x x x x x
X x x x x x x x x
500 HRS OR ANNUALLY
X
PROCEDURE
Check all hardware for proper tightness
Change engine oil and filter at 5 hours
Check engine oil
Remove debris from under belt cover
Sharpen cutter blades
Grease spindle bearings
Clean air filter
Check belt tension
Check tire pressure
Change engine oil
Replace air filter
Grease caster wheel bearings
Grease caster wheel pivot shafts
Grease idler pulley bracket on cutter deck
Grease drive wheel bearings
Grease
Grease transmission couplers idler bracket LH & RH
Check
Adjust all hardware for proper tighmess air gap on electric clutch
COMMENTS
Do not over fill
More often if needed
More often if needed
+ US Lithium MP White Grease 2125
More often if needed
Add or adjust as required
See engine lnfg. information
More often if needed
Chassis grease
Chassis grease
Chassis grease
Chassis grease
Chassis grease
Chassis grease
More often if needed
Contact your Scag dealer for information about making this adjustlnent
8
SCA6
CONDITION
TROUBLESHOOTING
CAUSE'
CUTTING CONDITIONS
CURE
Stringers - Occasional
Blades of Uncut
Low engine RPM
Ground speed too fast
Wet grass
Dull blades, incorrect sharpening
Deck plugged, grass accumulation
Belts slipping
Run engine at full 3600 RPM
Slow speed to adjust for conditions
Cut grass after it has dried out
Sharpen blades
Clean underside of deck
Adjust belt tensions
Streaking - Strips of
Uncut Grass in Cutting
Path
Streaking - Strips of
Uncut Grass Between
Cutting
Paths
Dull, worn blades incorrect blade sharpening
Low engine RPM
Belt slipping
Deck plugged, grass accumulation
Ground speed too fast
Wet grass
Bent blades
Sharpen blades
Sharpen blades
Run engine at full 3600 RPM
Adjust belt tension
Clean underside of deck
Slow speed to adjust for conditions
Cut grass after it has dried out
Replace blades
Not enough overlapping between rows increase the overlap of each pass
9
SCA6
TROUBLESHOOTING CUTTING CONDITIONS
CONDITION
Uneven Cut on Fiat
Ground - Wavy
High-Low
Appearance,
Scalloped Cut, or
Rough Contour
.=
CAUSE
Lift worn off of blade
Blade upside down
Deck plugged, grass accumulation
Too much blade angle (deck pitch)
J Deck mounted
improperly
Bent spindle area
Dull blade
CURE
Replace blade
Mount with cutting edge toward ground
Clean underside of deck
Adjust pitch and level
See your authorized SCAG dealer
See your authorized SCAG dealer
Sharpen blade
Uneven Cut on
Uneven Ground -
Wavy
Appearance,
High-Low Scalloped
Cut, or Rough Contour
Uneven ground May need to reduce ground speed, raise cutting height, and/or change direction of cut f i_i_i_i_ii_!!ii!i!i_i!iiiiliiiii_i_!i!i!i
Sloping Ridge Across
Width of Cutting
Path
Tire pressures not equal
Wheels uneven y
. Deck mounted incorrectly ij
Y
10
Check and adjust tire pressure
Check and adjust tire pressure
See your authorized SCAG dealer
SCA6
TROUBLESHOOTING
CUTTING CONDITIONS
_calping - Blades
_itting Dirt or
Jutting Very Close to he Ground
Low tire pressures
Ground speed too fast
Cutting too low
Rough terrain
Ground speed too fast
Wet grass
_tep Cut
_,idge in Center of
Jutting
Path
SGB022
Blades not mounted evenly
Bent blade internal spindle failure
Mounting of spindle incorrect
Check and adjust pressures
Slow speed to adjust for conditions
May need to reduce ground speed, raise cutting height, change direction of cut, and/or change pitch and level
May need to reduce ground speed, raise cutting height, and/or change direction of cut
Slow speed to adjust for conditions
Cut grass after it has dried out
Adjust pitch and level
Replace blade
See your authorized SCAG dealer
See your authorized SCAG dealer
¸ : i! iiiii'i,liiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii! i!:i
Bent spindle mounting area )lope Cut - Sloping
{idges Across Width
)f Cutting
Path
internal spindle failure
See your authorized SCAG dealer
See your authorized SCAG dealer
Bent deck housing See your authorized SCAG dealer
11
SCA6
MODELS
ENGINE
General Type:
Brand / Model:
Horsepower:
Type:
Displacement:
Governor:
Air Cleaner:
Exhaust:
Starter/Electrical:
Fuel Pump Group:
Oil Pump Group:
Valve Group:
ENGINE DECK
Thickness:
Fuel Tank:
Drive Wheels/Tires:
Handle Bars:
DRIVE SYSTEM
Type:
Transmissions:
Steering/Travel Control:
Brakes:
Axles:
Wire Harness:
Safety Group:
Forward Speed Range:
Reverse Speed Range:
Date of issue: June 15, 1999
Specifications Subject to Change Without Notice
TECHNICAL SPECiFiCATiONS
SW32-13KA, SW36-13KA, SW36-13KH, SW36-14KA, SW48-14KA,
SW48-15KH, SW48-17KA, SW48A- 17KA, SW52-17KA
Heavy duty industrial/commercial
Kawasaki FB460V, FC420V, & FH500V:
Kohler CV13, CV15T
Kawasaki FB460V=13 HP, FC420V=14HP, FH500V=17HP
Kohler CVl 3T=13HP, CVl 5T=15 HP
Kawasaki 13 HP, 14 HP, 4 cycle gasoline engine, air cooled, single cylinder, vertical shaft engine. 17HP 4 cycle, air cooled, V twin cylinder, verticl shaft engine.
Kohler 13 HP & 15 HP = 4 cycle gasoline engine, air cooled, single cylinder, vertical shaft engine.
Kaw. 13 HP=460cc, 14 HP=423cc: 17HP=494cc
Kohler 13 HP=398cc, 15 HP=426cc:
Mechanical type governor with variable speed control. Settings:
Kawasaki 13 HP= 3350 rpm (+/- 75 rpm), 14 HP=3600 rpm (+/-
75rpm), idle set at 1200 rpm (+/- 75 rpm), 17HP=3600 rpm, idle set at1550 rpm (÷/- 75 rpm)
Kohler 13 HP & 15 HP=3600 rpm (+/- 50 rpm), idle set at 1200 rpm
(+/- 75 rpm)
Large capacity duel element with cyclonic-type air filter.
Single & dual exhaust canister muffler.
Electronic ignition with recoil starter.
Varied - See manufacturer's specification.
Varied - See manufacturer's specification.
Varied - See manufacturer's specification.
7 gauge steel.
5 gallon (19.0 liters)seamless polyethylene.
13.0 x 6.50-6 two-ply pneumatic tubeless.
1-1/4" diameter.
Belt drive with twin power belts for increased friction to pulley surface.
Peerless 5-speed transmission, Model #700-070A.
Clutch/brake fingertip steering, key lock switch. (EZ Grip design allows minimum hand force to operate controls.)
6" drum, band brake, one on each wheel.
1"
14 gauge wire.
Hand actuated operator presence system with blade clutch and transmission interlock to engine kill.
0 to 6.0 mph
0 to 2.0 mph
12
SCA6
TECHNICAL SPECIFICATIONS (CON'T)
CUTTER
Type:
Construction:
DECK
True Cutting Width:
Blade Engagement:
Cutting Height Adjustment:
Cutter Blades:
SWM 32, SWM 36, SWM 48, SWM48A, SWM 52
Out-front design with anti-scalp rollers.
SWM32-48: 7-gauge steel with 7-gauge (3/16") steel skirt
SWM52:10-gauge steel with 7-gauge (3/16") steel skirt
SWM32=32.0" (81.3cm), SWM36=36.0" (90.2cm), SWM48=48.0"
(122.0cm), SWM48A=(122.0cm), SWM52=52.0" (132.0cm)
Electric blade engagement clutch with control panel switch
Manual adjustment 1-3/4" to 4-1/2" in 1/4" increments.
.204" thick, milled edge, 5150 alloy steel
SWM32 = Two (2) 16.5" blades, SWM36 = Two (2) 18" blades,
SWM48 = Three (3) 16.5" blades, SWM52 = Three (3) 18" blades
SWM32, 36, 52 Extra wide 11.5", SWM48 Extra wide 13.5", Discharge Opening:
CasterWheels: with quick pin removal.
9.4 x 3.5 smooth-tread flotation, inner tubes, split rims, roller bearings,
Spindles: grease fitting and grease overfill relief poppet.
Cast housing, taper roller bearing, low maintenance with top access
Spindle Pulleys:
Cutter Deck Belts:
Cast-iron with easily removed taper hubs
B-section with Kevlar® cord.
ADDITIONAL SPECIFICATIONS
OPTIONAL ITEMS/ATTACHMENTS
Fabric Grass Catcher:
Metal Grass Catcher:
Sulky:
Mulching Plate:
EZ-GRIP-SW
APPROXIMATE DIMENSIONS
Length:
Length with grass catcher:
Tracking Width:
Width:
Width (with discharge chute up):
Width with grass catcher:
Height:
Height with grass catcher:
Weight:
Weight with GC-F4 grass catcher:
Weight with GC-4D grass catcher:
GC-F4 Grass Catcher with 4 cubic ft. capacity
GC-4D Grass Catcher with 4 cubic ft. capacity and rope pull dump or pick-up and dump.
RS-2 Two-Wheel Sulky with padded seat.
RS-ZT Two-Wheel Zero Turn Sulky with padded seat.
Steel plate fits over discharge opening.
No blade change or removal required.
Installs and removes in the field.
Provides reduced hand force at operator steering controls.
SWM32 SWM36 SWM48 SWM48A
70.0"
70.0"
32.0"
43.0"
33.0"
51.0"
40.5"
40.5"
440 Ibs.
480 Ibs.
490 Ibs.
72.0"
72.0"
37.0"
48.0"
38.0"
56.0"
40.5"
40.5"
465 Ibs.
505 Ibs.
515 Ibs.
76.0"
76.0"
37.0"
60.0"
50.0"
68.0"
40.5"
40.5"
515 Ibs.
555 Ibs.
565 Ibs.
76.0"
76.0"
37.0"
60.0"
50.0"
68.0"
40.5"
40.5"
515 Ibs.
555 Ibs.
565 Ibs.
SWM52
76.0"
76.0"
37.0"
60.0"
53.0"
71.0"
40.5"
40.5"
525 Ibs.
565 Ibs.
575 Ibs.
Date of issue: June 15, 1999
Specifications Subject To Change Without Notice
13
SCA6
41
69
13
37
32" & 36" CUTTER DECKS
45
_44
46
59
14
22
58
51
56
61
29
33
4
3O
31
14
32
35_ -. \
IA
,..,,,
10
12
11
15
15A
16
14
32" & 36" CUTTER DECKS
Ref. Part
No.
Number
3
4
5
6
7
1 461130
1A 461131
2 46631
43312
48307-08
481022
43294
04001-108
8
9
10
11
12
13
14
43298
04001-77
04063-08
43278
04001-10
481050
04019-03
15
15
481706
481707
15A 481710
15A 481711
16 04040-10
17
18
19
04001-41
46079
04066-01
25
26
27
28
29
20
21
22
23
24
43037-01
48100-01
48114-04
46082
45006
43022
04001-37
04021-07
48307
48307-02
NS 48006-03
30 48307-04
31 48006-07
32
33
48006-06
48114-03
34
35
36
48006-05
04017-16
461054
37
38
04021-10
04001-09
39 46853
39A 46797
40
41
04041-07
04029-03
Description
Cutter Deck (includes Decals)
Cutter Deck (includes Decals)
Cutter Spindle Assy.
Spacer, Outside
Tapered Nut, 5/16-24
Tapered Bearing (Two)
Spindle Housing
Bolt, 5/16-18 x 4-1/4" Hex Head
Spindle Shaft
Bolt, 3/8-16 x 3-1/2" Hex Head
Key, 1/4 x 1/4 x 2"
Spacer, Cutter Blade - Small
Bolt,5/16-18 x 1-1/4" Hex Head
Spring, Chutte Return
Nut 5/16-18 Serrated Flange
Cutter Blade, 16-1/2" Marbain
Cutter Blade, 18" Marbain
Cutter Blade 16-1/2 Hi Lift Marbain
Cutter Blade, 18 Hi Lift Marbain
Flatwasher, 5/8 W
Hex Hd. Bolt, 5/8-11 x 9-1/2"
Caster Assembly (Inc.19-28)
Quick Pin
Spacer, Caster Yoke, 1/2" long
Bronze Bearing
Grease Fitting
Support Assembly (inc. 21-23)
Caster Yoke
Sleeve, Caster Wheel Bearing
Hex Hd. Bolt, 1/2-13 x 5-1/2"
Elastic Stop Nut, 1/2-13
Wheel Assy. (Inc.4, 29-34)
Tire only, Caster Wheel inner Tube only
Rim Pair, Caster Wheel
Retainer, Bearing, Caster Wheel
Roller Bearing, Caster Wheel
Grease Fitting, 45 degree 1/4-28
Hub Assembly
Cpscrw,5/16-18 x 3/4" Ser.FIg. Hex Head
Discharge Chute
Hex Nut, 5/16-18 Elastic Stop
Hex Hd Bolt, 5/16-18 x 1"
Belt Cover Assy (includes Decal)
Belt Cover Assy (includes Decal)
Flat Washer, 3/8" Special
Wing Nut, 3/8-16 x x x x x x x x x x x x x x
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Ref. Part
32 36 No.
Number x x
59
60
61
62
63
64
65
66
67
68
69
48
49
50
51
52
53
54
55
56
42
43
44
45
46
48924
48926
04001-01
04020-09
48278
46A 48204
47 43077
04021-05
04019-04
04004-02
04017-42
04019-05
43277
04041-12
04021-09
45423
57
58
46748
48100-02
04050-05
44078
48269
481024
43297
43296
481035
48677
481025
48098
04029-04
X
X
X
X
X
X
X
X
X
X
X
X
X
X x x x x x x x x x x x
X
X
X
Description
Pulley
Tapered Hub
Hex Hd. Bolt, 1/4-20 x 3/4"
Hex Nut, 5/8-11
Belt, Blade Drive
Belt, Blade Drive
Spacer
Hex Nut, 3/8-16 Center Locknut
Nut, 3/8-16 Serrated Flange
Support, Belt Cover
Cpscrw, 7/16-14 x l"Ser.FIg.
HH
Nut, 7/16-14 Serrated Flange
Spacer, J-Hook
Washer, 3/8 x 1-1/2 x 16 GA
Elastic Stop Nut, 3/8-16
idler Pivot
idler Arm Assy. (inc. 22 & 58)
Bronze Bearing
Retaining Ring, 1-1/8" Ext. "E"
J-Hook
idler Pulley, Belt Clutch
Seal, Cutter Spindle
Spindle Bushing
Spacer, inside
Nut,
Relief Fitting, Cutter Spindle
SeN, Cutter Spindle
Spindle Shield
Wing Nut, 3/8-16 (Small) RH side
SCA6
x x x x x
32 36 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
* Common hardware which should be purchased locally.
All bolts are Grade 5 plated, all other fasteners zinc plated.
15
SCA6
I
I
41
48, 52" CUTTER DECKS
45
1
44
45
44
43
48 45
37
29
37
23 25
79
80
30
31
1
10
32
31
12
11
16
17
15
15A
16
SW-SWZ 2KCD48, 52'
66
7
6
70
81
72
SCA6
48, 52" CUTTER DECKS
Ref.
Part
No.
No.
1 461132
18 46079
19 04066-01
20 43037-01
21 48100-01
22 48098
23 46082
24 45006
25 43022
26 04001-37
27 04021-07
28 48307
29 48307-02
NS 48006-03
30 48307-04
31 48006-07
32 48006-06
33 48114-03
34 48006-05
35 04017-16
36 461054
37 04021-04
38 04001-09
39 46798
39 461095
39 46804
40 04041-07
4
5
1
2
3
461264
46631
43296
48924
481022
6
7
8
43294
48114-04
43298
9 45037
10 04063-08
11 43278
12 04001-10
13 04001-108
14 04019-03
15 481706
15 481707
15A 481710
15A 481711
16 04040-10
17 04001-41
Description
Cutter Deck (includes decals)
Cutter Deck (includes decals)
Spindle Assembly
Spacer, inside
Pulley
Tapered Bearing (Two)
Spindle Housing
Grease Fitting Str. 5/16
Spindle Shaft, Tapered Brng
Idler Pivot
Key, 1/4 x 1/4 x 2"
Spacer, Cutter Blade - Small
Bolt, 5/16-18 x 1-1/4" Hex Head
Bolt, 5/16-18 x 4-1/4" Hex Head
Serrated Flange Nut, 5/16-18
Cutter Blade 16-1/2" Marbain
Cutter Blade 18" Marbain
Cutter Blade 16-1/2 High Lift Marbain
Cutter Blade 18 High Lift Marbain
Flatwasher,5/8" (.688 x 1.75 x .134)
Hex Head Bolt, 5/8-11 x 9-1/2"
Caster Assembly, (inc1.19-28 & 7)
Quick Pin
Spacer, Caster Yoke, 1/2" thick
Bronze Bearing
Spindle Shield
Support Assembly, (incl. 21-23)
Caster Yoke
Sleeve, Caster Wheel Bearing
Hex Hd Bolt, 1/2-13 x 5-1/2"
Elastic Stop Nut, 1/2-13
Wheel Assy.
(incl. 29-34,81)
Tire only, Caster Wheel inner Tube only, Caster Wheel
Rim Pair, Caster Wheel
Bearing Retainer, Caster Wheel
Roller Bearing, Caster Wheel
Grease Fitting 45 deg., 1/4-28
Hub Assembly, (incl. bolts)
Capscrew, 5/16-18 x 3/4"
Discharge Chute
Nut, 5/16-18 Elastic Elastic Stop
Bolt, 5/16-18 x 1" Hex Head
Belt Cover (Includes decals)
Belt Cover (Includes decals) 17KA
Belt Cover (includes decals)
Fiat Washer, 3/8" Special
48 52 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
Ref.
Part
No.
No.
Description
58 48181
59 04050-02
60 46081
61 48100-05
62 43028
63 43077
64 04041-12
65 04001-46
66 481024
67 46748
68 43277
69 48677
70 43312
71 43297
72 481035
73 04029-04
74 04001-77
75 45329
41 04029-03
42 48924
43 48926
44 04001-01
45 04020-09
46 48923
47 48087
47 48285
48 48089
48 48286
49 04021-05
50 04019-04
51 04021-09
52 04004-02
53 04001-08
Wing Nut, 3/8-16 (Large)
Pulley
Tapered Hub
Bolt, 1/4-20 x 3/4" Hex Head
Nut, 5/8-11 Hex
Pulley, Double
Belt, RH Blade Drive
Belt, RH Blade Drive
Belt, Blade Drive
Belt, Blade Drive
Nut, 3/8-16, Nut Centerlock
Nut, 3/8-16, Serrated Flange
Nut, 3/8-16 Elastic Stop
Support, Belt Cover
Bolt, 5/16-18 x 1/2" Hex Head
54 04017-42
55 04019-05
Cpscrw,7/16-14 x l"Ser Flng H Hd
Nut, 7/16-14 Serrated Flange
56 04041-08 Fiat Washer 3/4" Special
56A 04041-08S Flat Washer 3/4" Special
57 44078 J-Hook idler Pulley, "V" Groove
Retaining Ring, 3/4" Ext.'E" idler Arm Assy. (incl. 7 & 61)
Bronze Bearing
J-Rod, idler Pulley
Spacer,
Spacer,
Spindle
J-Rod
Washer, 3/8 x 1-1/2 x 16 ga.
Bolt, 3/8-16 x 2-1/4" Hex Head
Seal, Cutter Spindle idler Arm Assy (includes
J-Rod
Bushing
Nut, Cutter Spindle
Wing Nut, 3/8-16 (Small) Top Side
Bolt, 3/8-16 x 3-1/2" Hex Head idler Pivot
22&77)
Reiief Fitting, Cutter Spindle
Spacer, Outside, Cutter Spindle
76 48269
77 48100-02
78 04050-05
79 48038
80 45944
81 481025
82 481050
83 48307-08 idler Pulley, Belt Clutch
Bronze Bearing
Retaining Ring
Guide Roller
Roller Shaft
Seal, Cutter Spindle
Spring, Chute Return
Nut, 3/8-24 Tapered
* Common hardware which should be purchased locally.
All bolts are Grade 5 plated, all other fasteners zinc plated.
48 52 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
17
SCA6
_19
19 13KA
ONLY
56 ONLY
12
42
44 46
4O
11
KA Only
53 i
18 i
41
40,40A
37
39
39
38
38A
38B
38C
38D
47
2O
17
52
2
14
58
51
21
61
SW99ED
18
SCA6
Ref. Part
No.
No.
Description
ENGINE
DECK
13KH13KA
15KH14KA 17KA
Ref.
Part
NO.
No.
Description
13KH13KA
15KH14KA17KA
1A
1A
1B
1B
3
481775
481757
48841
48842
1C 481563
2 48030-09
481580
6
7
4 48231
5 48122-01
5A 48122-02
481581
48114-05
8 481582
8A 481583
9 04063-09
10 04003-12
11A 43100
11B 43085
11C 43104
12 49070-7002
13 04001-08
14 04040-14
15 04030-03
16 04019-04
17 46764
17A 46765
17B 46766
18 04021-08
19 04019-03
20 04001-51
21 461073
22 04041-07
23 48197
24 04063-07
25 04050-09
26 48203
27 481048
28 481666
29 04063-19
30 04041-28
Engine,13HP Kohler
(CV13T, SpecPS-2190)
Engine,15HP Kohler
(CV 15T, Spec PS-41581)
Engine 12.5HP Kawasaki
(Spec FB460-ES05)
Engine, 14HP Kawasaki (FC420V)
Engine, 17HP Kawasaki (FH500V) x x
Cable Clamp
Transmission, 5-speed
(Peerless 700-070, 9 tooth spline)
Neutral Safety Switch x x
Fibre Washer, thin
Fibre Washer, thick
Coupler, Jackshaft
Grease Fitting, straight 1/4-28
Jackshaft (fits SW32,36 & 48)
Jackshaft (fits SW52,61 & 72)
Key, Hi-Pro #9
Bolt, 5/16-18 X 3/4" Carriage x x
Wheel Axle (SW 52,61,72) **
Wheel Axle (SW36,48) ** x
Wheel Axle (SW 32) ** x
17KA Muffler (Purchase from Kawasaki)
Bolt, 5/16-18 X 3/4" Hex Head x
Flat Washer 1/4" (.312 X .75 X .065) x
Lock Wshr. 5/16" x x x x x x x x Nut, 3/8-16 Serrated Flange
Engine Deck (fits SW32)
Engine Deck (fits SW36 &48)
Engine Deck (fits SW52,61 & 72)
Nut, 1/4-20 Elastic Stop
Nut, 5/16-18 Serrated Flange
Bolt, 3/8-16 x 3-3/4" Hex Head
Electric Clutch (Ogura)
Washer, 3/8" (.391 x .938 x .105)
Pulley, Transmission Input
Key, Woodruff #9
Retaining Ring, 5/8" Ext, Basic
Belt, Transmission Drive
idler Pulley, Transmission
Pulley, Traction Drive
Key, 1/4 x 1/4 x 3/4"
Flat Washer, 7/16" Special x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
X
X
X
X
X
X
X
X
X
X x
X x x x x x x x
X x
X x x x x x x x
X x x x x x x x x x x x x
X
X
31
35
36
37
04030-05
32A 04001-101
32B 04002-15
33
34
04001-12
04002-07
04021-09
04040-15
04018-01
38 48192
38 48253
Lock Washer,7/16"
Bolt, 7/16-20 x2-1/2" Hex Head x
Cpsrw, M10-1.5 x55 Metric Hex Hd x
Bolt, 5/16-18 x 1-3/4" Hex Head x
Bolt, M8-1.25 x 1.0
x
Nut, 3/8-16 Elastic Stop x
Flat Washer, 5/16" x
Bolt, M8-1.25 x M25 Metric Hex Hd x
Wheel Assembly (incl. 38A-38B) x
(fits SW36,48,52,61,72)
Wheel Assembly x
56
57
58
59
60
61
49
5O
51
52
53
54
55
38A 48192-02
(incl. 38C-38D) (SW32)
Tire, 13 x 6.50-6, 2-ply
(fits SW36,48,52,61 & 72) x
38B 48193-03 Rim & Bearing Assembly (incl. 39)
(fits SW36,48,52,61 & 72) x
38C 48253-02
38D 48253-03
39 48193-02
40 04042-05
40A 04041-14
41
42
43
04050-08
48200
43088
48209
44
45 04017-19
04003-03 46
47
48
04021-10
Tire, 13 x 5.00-6 2-ply (SW32 only)
Rim Assembly (incl. 39) (SW32 only)
Wheel Brng. NWC (OD 1.984-1.980) x
Washer,
Washer,
Retaining
1-1/16 x 1-3/4 x 12 ga
1-1/16 x 1-1/2 x 18 ga
Ring, 1" Ext.-"E"
Pulley, Wheel Drive
Spacer, Wheel Pulley
Brake Drum x x
Bolt, 5/16-18 x 1-1/2" Serrated flange x
Bolt, 3/8-16 x 2" Carriage
Nut, 5/16-18 Elastic Stop
21013-2064 Condenser (order from Kawasaki) x x x x x x
422930
04001-09
481716
04003-02
21066-2071
422533
04001-59
481717
04031-09
421370
04003-04
04021-08
422534
Bracket, Capacitor
Bolt, 5/16-18 x 1" Hex Head
Rubber Pad, Clutch Stop
Bolt, 1/4-20 x 3/4" Carriage
Rectifier (order from Kawasaki)
Backing Plate
Bolt, 1/4-20 x 1-1/4"
Wire Harness Adapter, 17KA
Lock Washer Internal Tooth
Anti Rotation
Bolt, 5/16-18 x 1" Carriage
Nut, 1/4-20 Elastic Stop
Plate, Backing
Bracket x x x x x x x x x x
** = Requires welding onto chassis.
* Common hardware which should be purchased locally.
All bolts are Grade 5 plated, all other fasteners zinc plated.
x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
19
SCA6
72 24
71
HANDLE
ASSEMBLY
28
30A
47
63_
62
63
64
66
51 9 46
k
49
65
65B
59
67
55 52 54
5761
82
I
A_ H G
19
TRACTION PLUS ACCESSORIES
(OPTIONAL)
(RVS-SM)
(RVS-LG)
45
15A
14
16
22
12 22
5
19
2
21
19
5
SW 2K HA
20
SCA6
HANDLE
ASSEMBLY
Ref.
Part
NO.
NO.
Description
1
1
2
461126
46856
421360
Handle Assembly (Fits SW 36,48) x
Handle Assembly (Fits SW52,61,72) x
Belt Guard x
6
7
8
9
3
4
5
10
11
12
13
04017-27 Capscrw, 3/8-16 x 1" Set. Flange
04041-07 Washer, 3/8" (.391 x .938 x .105)
04021-09 Nut, 3/8-16 Elastic Stop
48755 Spring, idler
04001-10 Bolt, 5/16-18 x 1-1/4" Hex Head
04021-10 Nut, 5/16-18 Elastic Stop x
04017-05 Capscrew, 1/4-20 x 3/4" Hex Head x x x x x x
44004 Control Rod, Steering
04062-02 Hair Pin, Small
04001-23 Bolt, 3/8-16 x 4-1/2" Hex Head
43032 Swivel Joint x x x x
14 04062-01 Hair Pin, Large .094 Diameter
15 45847
15A 45846
16 43092
Idler Bracket, RH
Idler Bracket, LH
Idler Sleeve
17
18
19
20
21
22
23
24
31
32
33
34
35
25
26
27
28
04001-62 Bolt, 3/8-16 x 3/4" Hex Head
04004-17 Support Belt Guard
04019-04 Nut, 3/8-16 Serrated Flange x
04019-03 Nut, 5/16-18 Serrated Flange x
04017-28 Cpscrw, 3/16-18 x 1-1/4" Set. Flng.
x
43286
48309
48292
46089
04017-17
45572
44005
45092
45093
42254
Spacer
Bushing
Rubber Pad, (Upper)
Steering
Capscrew,
Lever
Brake Lever
Brake Link
5/16-18 x 1" Set. Flng.
29
30
48312 Bushing
04040-15 Washer, 5/16 (.375 x .875 x .083)
48951
45573
Spring, Operator Presence
Operator Presence Lever,
LH (Small Frame)
30A 45571 Operator Presence Lever,
LH (Large Frame)
Operator Presence Lever, RH
Brake Rod
Brake Link Plate x x x x x x x x x x x x x x x x x x x x x
36
37
38
39
40
41
04024-01
04031-08
Nut, 3/8 Push-on
48114-05 Grease Fitting, Straight 1/4-28
04050-01 Retaining Ring, 5/8 Ext. "E"
48210 Brake Band
04001-45 Bolt, 3/8-16 x 2" Hex Head
1/4" Internal Tooth Lockwasher
42
43
44
45 461242
45A 461241
46
47
04032-01 Curved Spring Washer x
04015-13 Socket Head Capscrew #8-32 x 1/2" x
04020-02 Nut, 1/4-20 Hex x
48205
48202A
Neutral Latch, RH
Neutral Latch, LH
Rubber Pad (Lower)
Belt, Wheel Drive x x x x
48
49
50
51
52
53
48198
48199
Idler Pulley, Wheel Drive
04012-04 Setscrew, Hex Socket Knurl
43098
48223
48224
Pulley, Jackshaft (Inc. 50)
Cup Pt. 5/16-18 (nylock)
Spacer, Jackshaft Pulley
Flange, Jackshaft Bearing
Bearing, Jackshaft x x x x x x x x x x x x
13KHI3KA
15KHI4KA17KA x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
Ref.
Part
NO.
No.
Description
68
69
70
71
72
73
74
80
81
82
75
76
77
78
79
54
55
56
57
58
04050-09 Retaining Ring, 5/8 Ext. Basic
04017-06 Capscrew, 1/4-20 x 1" Ser. Flange
04003-01 Bolt, 1/4-20 x 6" Carriage
48030-09 Clamp
04001-17 Bolt, 5/16-18 x 2" Hex Head
59
60
61
62
63
64
04019-02
04040-15
04021-02
48179
Nut, 1/4-20 Serrated
Flatwasher,
Flange
5/16 (.375 x .875 x .083)
Nut, 1/4-20 Elastic Stop
Fuel Hose 7/32 ID x 3.5"(Kaw.
48059-02 Fuel Hose Clamp (Kaw. Only)
48057-02 Fuel Filter (Kawasaki Only)
65 48058 Fuel Hose,1/4"lD, 10" (KH Only)
65A 48058
66
67
48059-01
481072
Fuel Hose,1/4"lD,
Clamp, Fuel Hose
Choke Control
20" (Kaw.)
Only)
48159
48308
46174
481603
421239
Grip, Handle
Valve, Fuel Shut Off
Fuel Tank Assy.(Incl.
Bush. & Val.)
Fuel Tank Cap
Strap, Fuel Tank
04010-10 Screw, 1/4-20 x 2" Rnd Hd Slotted
422279 Shift Lever
461163
48144
04041-07
04020-14 Nut, 3/8-24 UNF
48028-05 Cable Tie
04001-53
481839
421622
Shift Lever Extention
Grip, Steering
Washer,
Lever
3/8 (.391x
Bolt, 5/16-18 x 2-1/2"
Grip, Shift Handle
(incl. 81)
.938 x .105)
Bracket, Choke Mt. (Kaw.
17)
13KH13KA
15KH14KA 17KA x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
A
B
C
D
E
EA
F
G i
H
IA
J
JA
Traction Plus Accessories (Optional), RVS-SM & RVS-LG
04017-27 Capscrew, 3/8-16 x 1" Ser. FIng
44098
43032
Rod, Traction
Swivel Joint
Control
04062-01 Hair Pin, Large .094 Dia.
421372
421373
Mounting
Mounting
Brkt. LH Traction
Brkt. RH Traction
Cont.
Cont.
04019-04 Nut, 3/8-16 Serrated Flange
04017-16 Capscrew, 5/16-18 x 3/4" Ser. Fig.
04019-03 Nut, 5/16-18 Serrated Flange
421428
Traction Lever, LH
421429
45554
Traction Lever, RH
45555
Traction Lever WIdmnt.
(Small Fm.)
Traction Lever Wldmnt. (Large Fm.) x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
21
SCA6
iNSTRUMENT
PANEL
2A
7
\
SW991P
Ref.
Part
No, No.
1 48717
2A 481071
6
7
8
NS
4
5
2B 48946
3 481687
48609
48023
*
04019-01
481678
48030-09
Description
Switch, Neutral
interlock
Throttle Control
Throttle Control (17KA)
Engagement Switch, Electric Clutch
Key Switch (includes hardware)
Hour Meter (dealer
installed)
Screw, #10-32 x .50 Phillips Washer Head
Nut, #10-32 Serrated Flange Hex Head
Handle Wire Harness, Manual Start
Clamp, Wire Harness x x x x x x x
13KH 13KA
15KH 14KA 17KA x x x x x x x x x x x x x x x x x x x x
* Common hardware which should be purchased locally.
All bolts grade 5 plated, all other fasteners zinc plated.
22
SCA6
31
52
44
38
82
34
150
Pa_
No.
772083A
780086A
780142
770061A
792089A
784266
784376
778154
778176
792077
792078
792079
780071
792073
792035
788040
780072
780108
792001
780105A
778146A
Ref.
No.
28
29
30
32
34
49
21
22
24
25
27
12
20
9
10
11
1
2
2A
3
8
Description
Case, Transmisson
Needle Bearing Grease Spec
Needle Bearing
Case, Transmission
Shift Key
Shift Collar
Shift Rod & Fork
Bevel Gear (42 teeth)
Bevel Pinion (14 teeth-steel)
Steel Ball, 5/16" dia.
Set Screw, 3/8-16 x 3/8"
Spring
Thrust Bearing
Screw, 1/4-20 x 1-1/4" (6)
Retaining Ring
Retaining Ring
Washer (6)
Washer (5)
"O" Ring
Flanged Bushing
Spur Gear (37 teeth)
23
REF.
PART
NO.
NO.
59
60
65
66
67
50
51
52
53
56
57
58
71
72
81
788069
792074
786081
82
83
786082
786083
90 788067B
150 510334
178
179
*
*
778125
778239A
778124A
778123A
778145
778151
778240
778126A
778127A
780139
776135
776402
DESCRIPTION
Spur Rear (35 teeth)
Spur Gear (32 teeth-steel
Spur Gear (30 teeth)
Spur Gear (25 teeth)
Spur Gear (12 teeth-steel
Spur Gear (15 teeth)
Spur Gear (18 teeth-steel
Spur Gear (20 teeth)
Spur Gear (25 teeth)
Washer
Input Shaft (3-11/16" long)
Shifter & Brake Shaft
Square Cut Ring
Threaded Plug (Shipping only, not used)
RoNer Chain (No. 41 chain, 24 links)
Sprocket (9 teeth)
Sprocket (18 teeth)
Grease (32 oz. bottle Bentonite grease)
Gasket Eliminator (Loctite #515)
CoupNng (See page 18-19 for part number)
Connector Shaft (See page 18-19 for part number
SCA6
BLACKW/RED
STRIPE--
BLACK
BLUE
WHITE_
WHITE
ELLOW
INSTRUMENT
PANEL HARNESS
NEUTRAL
INTERLOCK
E
_]
--
ENGINE
E
_1
DD
WW
ENGINE DECK WIRE HARNESS -
14 H P KAWASAKI
PART NO. 481074
BLACK'__
BLADE
CLUTCH
SW99WH481074
GROUND
WIRE HARNESS WITH RELAY
PART NO. 481275
To Engine
Ground
RELAY__
_
I_ n=11
_L.-_/
BLACK
_
BLUE
sc_7_ _-_2o_ _n0'ne
"t__)) To Starter
_ Red Battery
Cable Post
24
SCA6
HANDLE WIRE HARNESS -
MANUAL START
PART NO. 481678
BLACK
BLKW/RED STRIPE
|
I
PRESENCE
SWITCH
SWITCH
#
KEY
WHIT
O
QD
POS
HOURMETER
NEG
HOURMETER
MOWER
ENGAGE
SWITCH
BLK W/REDyELLowBLACKwHITEBLuESTRIPE
TO ENGINE
DECKWlRE
HARNESS
SW99WH481678
NEUTRAL
INTERLOCK
E N
BLADE
CLUTCH
GROUND
ENGINE DECK
WIRE HARN ESS -
KOH LER
(SINGLE CYLINDER)
17 H P KAWASAKI
PART NO. 481073
INSTRUMENT
PANEL HARNESS
RED
BLACK
BLUE
WHITE
WHITE
ELLOW
BLACK
D
WIRE
HARNESS
ADAPTER
- ENGINE
SW99WH481073
25
SCA6
LL_ULF_j_=_j
MOWER DECK
PULL OUT TO ENGAGE
ONI _
O OFF
,, F4
\\\
\
481684
I*tj
KEEp_ BYS_TAN DERSAWAZ
\
/
PUSH tN TO DISENGAGE
481684
F/UlT
///
32"-48315
36"-48316
48"-48318
52"-48319
481122
ROTATING BLADES AND BELTS
• KEEP HANDS, FEET & CLOTHING
CLEAR
• KEEP ALL GUARDS IN PLACE
• SHUT OFF ENGINE
& DISENGAGE BLADE
CLUTCH BEFORE SERVICING
• CLEAR AREA
OF DEBRIS BEFORE MOWING
• USE CAUTION
IN DIRECTING DISCHARGE
• KEEP BYSTANDERS,
CHILDREN & PETS AWAY
• READ INSTRUCTION
MANUAL BEFORE OPERATING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
481040
RN
n n
481040
2
48332
26
SCA6
/_ i i i
",
,,"/
481483
8LOW
SPINNING BLADE
KEEP CLEAR
CONTACT CAN INJURE
48071
48071
INSTALL BELT COVER BEFORE
OPERATING MACHINE
481039
48404
I Heavy-Du.tyl
Commerclal
481971
MANUFACTURED UNDER
ONE
OR MORE
OF THE FOLLOWING
PATENTS:
4,487,006
4,885,903
4,920,733
4,967,543
4,991,
4,998,
5,118,
5,826,418
382
948
817
PATENTS PENDING
5,832,708
5,865,018
48656
FALLING HAZARD
USE ONLY SCAG APPROVED
RIDING ATTACHMENTS
SEE OPERATOR'S MANUAL
481109
481109
27
LiMiTED WARRANTY-COMMERCIAL EQUIPMENT
Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. This warranty is limited to the original purchaser and is not transferable.
Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an
Authorized Scag Service Dealer.
This warranty is limited to the following specified periods from the date of the original retail purchase for defects in materials or workananship:
Wear items including drive belts, blades, hoses and tires are warranted for 90 days.
* Batteries are warranted for 90 days.
* Frames, decks, and structural components including oil reservoirs and oil coolers are warranted for ! year.
* Engines and electric starters are warranted by the manufacturer's warranty period.
* Hydro-Gear(R) drive components are warranted by Hydro-Gear, Sullivan, IL.
* Drive system components are warranted for ! year by the component manufacturer, in coniunction with Scag Power Equipment.
(Excluding fittings, hoses, cooling systems, oil reservoirs, and drive belts).
* Electric clutches have a Limited Warranty for 2 years (parts & labor 1st year; parts only
2nd year).
* Cutter Spindle Assemblies 4663 ! have a Limited Warranty for 3 years (parts and labor 1st year; parts only 2nd and 3rd years).
Any Scag product used for rental purposes is warranted by a 90-day warranty period.
The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner.
Scag's responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.
This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual. The warranty does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have not been assembled or installed as specified in the Operator's Manual and Assembly Manual. The warranty does not cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability.
Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obligation to modify any mower previously
manufactured.
All other implied warranties are limited in duration to the one (1) year warranty period or ninety (90) days for mowers used for rental purpose.
Accordingly, any such implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate one year or ninety day warranty period.
Scag's obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner, mechanic's travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
@ 1999
SCAG
POWER
EQUIPMENT
DiViSiON OF METALCRAFT OF MAYVILLE,
iNC.
PART NO. 03072
PRINTED
6/99
PRINTED
iN USA
advertisement
Related manuals
advertisement