YASKAWA
DX100 OPTIONS
INSTRUCTIONS
FOR JOB DATA SIMPLIFIED RESTORATION FUNCTION
Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain
for future reference.
MOTOMAN INSTRUCTIONS
MOTOMANINSTRUCTIONS
DX100 INSTRUCTIONS
DX100 OPERATOR’S MANUAL
DX100 MAINTENANCE MANUAL
The DX100 operator’s manuals above correspond to specific usage.
Be sure to use the appropriate manual.
Part Number: 157793-1CD
Revision: 0
YASKAWA
MANUAL NO.
HW0485567
1/24
HW0485567
DX100
MANDATORY
•
This manual explains Job data simplified restoration function of the
DX100 system. Read this manual carefully and be sure to
understand its contents before handling the DX100.
•
General items related to safety are listed in Chapter 1: Safety of the
DX100 Instructions. To ensure correct and safe operation, carefully
read the DX100 Instructions before reading this manual.
CAUTION
•
Some drawings in this manual are shown with the protective covers
or shields removed for clarity. Be sure all covers and shields are
replaced before operating this product.
•
The drawings and photos in this manual are representative
examples and differences may exist between them and the
delivered product.
•
YASKAWA may modify this model without notice when necessary
due to product improvements, modifications, or changes in
specifications. If such modification is made, the manual number will
also be revised.
•
If your copy of the manual is damaged or lost, contact a YASKAWA
representative to order a new copy. The representatives are listed
on the back cover. Be sure to tell the representative the manual
number listed on the front cover.
•
YASKAWA is not responsible for incidents arising from
unauthorized modification of its products. Unauthorized modification
voids your product’s warranty.
ii
HW0485567
2/24
HW0485567
DX100
Notes for Safe Operation
Read this manual carefully before maintenance or inspection of the
DX100.
In this manual, the Notes for Safe Operation are classified as “WARNING,”
“CAUTION,” “MANDATORY,” or ”PROHIBITED.”
WARNING
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury to
personnel.
Indicates a potentially hazardous
situation which, if not avoided, could
result in minor or moderate injury to
personnel and damage to equipment.
It may also be used to alert against
unsafe practices.
Always be sure to follow explicitly the
MANDATORY items listed under this heading.
PROHIBITED
Must never be performed.
Even items described as “CAUTION” may result in a serious accident in
some situations. At any rate, be sure to follow these important items.
NOTE
To ensure safe and efficient operation at all times, be sure
to follow all instructions, even if not designated as “CAUTION” and “WARNING.”
iii
HW0485567
3/24
HW0485567
DX100
WARNING
•
Before operating the manipulator, check that servo power is turned
OFF pressing the emergency stop buttons on the front door of the
DX100 and the programming pendant.
When the servo power is turned OFF, the SERVO ON LED on the
programming pendant is turned OFF.
Injury or damage to machinery may result if the emergency stop circuit
cannot stop the manipulator during an emergency. The manipulator
should not be used if the emergency stop buttons do not function.
Fig. : Emergency Stop Button
•
Once the emergency stop button is released, clear the cell of all
items which could interfere with the operation of the manipulator.
Then turn the servo power ON.
Injury may result from unintentional or unexpected manipulator motion.
Fig. : Release of Emergency Stop
TURN
•
Observe the following precautions when performing teaching
operations within the P-point maximum envelope of the
manipulator:
– View the manipulator from the front whenever possible.
– Always follow the predetermined operating procedure.
– Keep in mind the emergency response measures against the
manipulator’s unexpected motion toward you.
– Ensure that you have a safe place to retreat in case of
emergency.
Improper or unintended manipulator operation may result in injury.
•
Confirm that no person is present in the P-point maximum envelope
of the manipulator and that you are in a safe location before:
– Turning ON the power for the DX100.
– Moving the manipulator with the programming pendant.
– Running the system in the check mode.
– Performing automatic operations.
Injury may result if anyone enters the P-point maximum envelope of the
manipulator during operation. Always press an emergency stop button
immediately if there is a problem.
The emergency stop buttons are located on the right of front door of the
DX100 and the programming pendant.
iv
HW0485567
4/24
HW0485567
DX100
CAUTION
•
Perform the following inspection procedures prior to conducting
manipulator teaching. If problems are found, repair them
immediately, and be sure that all other necessary processing has
been performed.
– Check for problems in manipulator movement.
– Check for damage to insulation and sheathing of external wires.
•
Always return the programming pendant to the hook on the cabinet
of the DX100 after use.
The programming pendant can be damaged if it is left in the
manipulator's work area, on the floor, or near fixtures.
•
Read and understand the Explanation of Warning Labels in the
DX100 Instructions before operating the manipulator:
Definition of Terms Used Often in This Manual
The MOTOMAN manipulator is the YASKAWA industrial robot product.
The manipulator usually consists of the controller, the programming
pendant, and supply cables.
In this manual, the equipment is designated as follows.
Equipment
Manual Designation
DX100 controller
DX100
DX100 programming pendant
Programming pendant
Cable between the manipulator and the
controller
Manipulator cable
v
HW0485567
5/24
HW0485567
DX100
Descriptions of the programming pendant keys, buttons, and displays are
shown as follows:
Equipment
Programming Pendant
Manual Designation
Character
Keys
The keys which have characters printed on
them are denoted with [ ].
ex. [ENTER]
Symbol
Keys
The keys which have a symbol printed on
them are not denoted with [ ] but depicted
with a small picture.
ex. page key
GO
BACK
PAGE
The cursor key is an exception, and a picture is not shown.
Axis Keys
Numeric
Keys
“Axis Keys” and “Numeric Keys” are
generic names for the keys for axis operation and number input.
Keys
pressed
simultaneously
When two keys are to be pressed simultaneously, the keys are shown with a “+” sign
between them, ex. [SHIFT]+[COORD]
Displays
The menu displayed in the programming
pendant is denoted with { }.
ex. {JOB}
Description of the Operation Procedure
In the explanation of the operation procedure, the expression “Select • • •”
means that the cursor is moved to the object item and the SELECT key is
pressed, or that the item is directly selected by touching the screen.
vi
HW0485567
6/24
HW0485567
DX100
Contents
1 Outline ............................................................................................................................................ 1-1
2 Job Data Restoration ...................................................................................................................... 2-1
2.1 How to Check Job Data Inconsistent Status...................................................................... 2-1
2.2 Job Data Restoration Method ............................................................................................ 2-4
2.2.1 In Case Same Position Data is Chained .............................................................. 2-4
2.2.2 In Case Not-Registered Position Data is Chained................................................ 2-7
2.2.3 In Case Not-Chained Position Data Exists ......................................................... 2-10
3 If Fail in Simplified Restoration ....................................................................................................... 3-1
3.1 Rechecking Job Data......................................................................................................... 3-1
3.2 If Data Inconsistency Alarm Occurs Again ........................................................................ 3-2
4 Related Parameters ........................................................................................................................ 4-1
5 Specific Output Signal..................................................................................................................... 5-1
vii
HW0485567
7/24
HW0485567
DX100
1
1
Outline
Outline
There are some cases where the data in file system becomes inconsistent
status if the controller power is turned off during edit operation.
If this data inconsistent status is neglected, the following data errors
(inconsistent status) might occur in rare cases.
This Job data simplified restoration function checks the inconsistent status
of the file and restore the data error status of the file system.
[Inconsistent status]
inconsistent chain status between position data and instruction file
(1) Overlapped chain with same position data
(2) Unregistered position data is chained with instruction file
(3) Registered position data is not chained
1-1
HW0485567
8/24
HW0485567
2
2.1
DX100
2
Job Data Restoration
How to Check Job Data Inconsistent Status
Job Data Restoration
2.1
How to Check Job Data Inconsistent Status
* “FILE” in WRONG DATA LOG screen corresponds to the following data.
(1) Job data
(2) User coordinate data (UFRAME)
(3) Robot calibration file (RBCAL)
(4) Edit buffer (-CUTBUF)
NOTE
•
Execute Job data restoration in management mode.
•
Operation mode and editing mode permit monitoring
only.
1. Detect data error
– ALARM screen appears.
2-1
HW0485567
9/24
HW0485567
DX100
2
2.1
Job Data Restoration
How to Check Job Data Inconsistent Status
2. Press {SYSTEM INFO} under main menu and select {SECURITY}
3. Select “MANAGEMENT MODE”
– Input password to switch the mode to Management mode.
4. Press {SETUP} under main menu and select {WRONG DATA LOG}
2-2
HW0485567
10/24
HW0485567
DX100
2
2.1
Job Data Restoration
How to Check Job Data Inconsistent Status
– WRONG DATA LOG screen appears.
5. Check the details of data inconsistency
– Check the error contents, then execute restoration following
chapter 2.2 “Job Data Restoration Method” at page 2-4.
2-3
HW0485567
11/24
HW0485567
2
2.2
DX100
2.2
2.2.1
Job Data Restoration
Job Data Restoration Method
Job Data Restoration Method
In Case Same Position Data is Chained
1. Press {UTILITY} to select {RESTORE}
– Press {RESTORE} to reset the overlapped position data chain.
2-4
HW0485567
12/24
HW0485567
DX100
2
2.2
Job Data Restoration
Job Data Restoration Method
– The indication changes from “OCCURRED ON” to “RESTORED
ON”.
* If fail in the restoration
– If the indication doesn’t change from “OCCURRED ON” to
“RESTORED ON”, refer to chapter 3 “If Fail in Simplified
Restoration” at page 3-1.
2. Start up the system again
– After the restoration, the system must be started up again.
Turn the control power OFF/ON and then execute the following
checking operation.
3. Press {SETUP} under main menu and select {WRONG DATA LOG}
2-5
HW0485567
13/24
HW0485567
DX100
2
2.2
Job Data Restoration
Job Data Restoration Method
– WRONG DATA LOG screen appears.
4. Check the position
– Check the position of two lines indicated in the screen.
2-6
HW0485567
14/24
HW0485567
DX100
2.2.2
2
2.2
Job Data Restoration
Job Data Restoration Method
In Case Not-Registered Position Data is Chained
1. Press {UTILITY} and select {RESTORE}
– Press {RESTORE} button to register the position of the file indicated
in WRONG DATA LOG screen tentatively, which enables to register
position again.
2-7
HW0485567
15/24
HW0485567
DX100
2
2.2
Job Data Restoration
Job Data Restoration Method
– The indication changes from”OCCURRED ON” to “REGISTERED
ON”.
* If fail in the restoration
– If the indication doesn’t change from “OCCURRED ON” to
“RESTORED ON”, refer to chapter 3 “If Fail in Simplified
Restoration” at page 3-1.
2. Start up the system again
– After the restoration, the system must be started up again.
Turn the control power OFF/ON and then execute the following
checking operation.
3. Press {SETUP} under main menu and select {WRONG DATA LOG}
2-8
HW0485567
16/24
HW0485567
DX100
2
2.2
Job Data Restoration
Job Data Restoration Method
– WRONG DATA LOG appears.
4. Register teaching position again
– Register the position data of the file in the screen again.
2-9
HW0485567
17/24
HW0485567
DX100
2
2.2
Job Data Restoration
Job Data Restoration Method
2.2.3
In Case Not-Chained Position Data Exists
1. Press {UTILITY} and select {RESTORE}
– Press {RESTORE} to correct the chain.
2-10
HW0485567
18/24
HW0485567
DX100
2
2.2
Job Data Restoration
Job Data Restoration Method
– The indication changes from “OCCURRED ON” to “REGISTERED
ON”.
* If fail in the restoration
– If the indication doesn’t change from “OCCURRED ON” to
“RESTORED ON”, refer tochapter 3 “If Fail in Simplified
Restoration” at page 3-1.
2. Start up the system again
– After the restoration, the system must be started up again.
Turn the control power OFF/ON.
2-11
HW0485567
19/24
HW0485567
3
3.1
DX100
3
If Fail in Simplified Restoration
Rechecking Job Data
If Fail in Simplified Restoration
Execute the following procedure if failing in the restoration by Job data
simplified restoration method.
3.1
Rechecking Job Data
1. Select {RE CHECK} under {UTILITY}
– Press {RE CHECK}
2. Restoration is completed.
– * Proceed to the next operationchapter 3.2 “If Data Inconsistency
Alarm Occurs Again” at page 3-2 if the alarm occurs again after this
operation.
3-1
HW0485567
20/24
HW0485567
3
3.2
DX100
3.2
If Fail in Simplified Restoration
If Data Inconsistency Alarm Occurs Again
If Data Inconsistency Alarm Occurs Again
Execute the following procedure if the data inconsistency alarm occurs
again even after rechecking Job data following chapter 3.1 “Rechecking
Job Data” at page 3-1.
1. Re-register the position data after deleting the data of the file indicated
in WRONG DATA LOG screen.
Refer to chapter 2.2 “Job Data Restoration Method” at page 2-4
for checking operation after registration. (See the operations after
procedure 2 “Start up the system again”.)
2. Execute the following procedures if the position data cannot be
deleted or re-registered with the operation indicated above.
(1) Save Job data and User Coordinate file and Robot Calibration.
*Delete the position data of the file indicated in WRONG DATA
LOG screen in case the following error occurs while saving.
ERROR: 0040 Undefined robot position variable
* Refer to“7.3.0.2 Saving Data”in “DX100 OPERATOR’S
MANUAL”for details.
(2) Initialize Job area in maintenance mode.
*Refer to “8.18.1 Initializing Job File” in “DX100 INSTRUCTIONS”
for details.
(3) Load the data saved in the procedure 1.
* Refer to “7.3.0.3. Loading Data” in “DX100 OPERATOR’S MANUAL” for details.
(4) Check the motion of the manipulator after loading.
* Refer to the procedure from procedure “2. Start up the system
again.” in chapter 2.2 “Job Data Restoration Method” at page 2-4.
3-2
HW0485567
21/24
HW0485567
DX100
4
4
Related Parameters
Related Parameters
Parameter
Meaning
Setting value
Initial
value
S2C303
Data inconsistency check
specification
0:Valid
1:nvalid
0
S2C304
Inconsistency detection method
in play mode
0:Warning
1:Stop with alarm
0
4-1
HW0485567
22/24
HW0485567
DX100
5
5
Specific Output Signal
Specific Output Signal
The following signal outputs the status of data inconsistency occurrence.
Output signal
Meaning
50696
Indicate the data inconsistency occurrence
5-1
HW0485567
23/24
DX100 OPTIONS
INSTRUCTIONS
FOR JOB DATA SIMPLIFIED RESTORATION FUNCTION
HEAD OFFICE
2-1 Kurosaki-Shiroishi, Yahatanishi-ku, Kitakyusyu-shi, 806-0004, Japan
Phone +81-93-645-7745
Fax +81-93-645-7746
MOTOMAN INC. HEADQUARTERS
805 Liberty Lane, West Carrollton, OH 45449, U.S.A.
Phone +1-937-847-6200
Fax +1-937-847-6277
MOTOMAN ROBOTICS EUROPE AB
Franska Vagen 10, Box 4004, SE-390 04 Kalmar, Sweden
Fax +46-480-417999
Phone +46-480-417800
MOTOMAN ROBOTEC GmbH
Kammerfeld strasse 1, 85391 Allershausen, Germany
Phone +49-8166-90-100
Fax +49-8166-90-103
YASKAWA ELECTRIC KOREA CORPORATION
1F, Samyang Bldg. 89-1, Shinchun-dong, Donk-Ku, Daegu, Korea
Fax +82-53-382-7845
Phone +82-53-382-7844
YASKAWA ELECTRIC (SINGAPORE) PTE. LTD.
151 Lorong Chuan, #04-01, New Tech Park, Singapore 556741
Fax +65-6289-3003
Phone +65-6282-3003
YASKAWA ELECTRIC (MALAYSIA) SDN. BHD.
Unit 47-1 and 2. Jalan PJU 5/9, Dataran Sunway, Kota Damansara, 47810, Petailng Jaya Selangor, Malaysia
Phone +60-3614-08919
Fax +60-3614-08929
YASKAWA ELECTRIC (THAILAND) CO., LTD.
252/246, 4th Floor. Muang Thai-Phatra office Tower II Rechadapisek Road, Huaykwang Bangkok 10320, Thailand
Phone +66-2-693-2200
Fax +66-2-693-4200
SHOUGANG MOTOMAN ROBOT CO., LTD.
No.7,Yongchang-North Road, Beijing Economic and Technological and Development Area, Beijing 100076, China
Fax +86-10-6788-0542
Phone +86-10-6788-0541
MOTOMAN MOTHERSON ROBOTICS LTD.
Plot Number 195-196, First Floor, Imt Manesar -Sector 4, Gurgaon (Haryana),Pin-122050, India
Phone +91-124-475-8500
Fax +91-124-475-8542
YASKAWA ELECTRIC CORPORATION
YASKAWA
Specifications are subject to change without notice
for ongoing product modifications and improvements.
C Printed in Japan March 2010 10-03
MANUAL NO.
HW0485567
24/24
">
