The Desk You Deserve
www.studiodesk.net
Video manual
ASSEMBLY MANUAL
FANTOM Series
Video Assemblymanual is also available.
Scanthe QRcode for direct link to the video manual.
NOTE:
We highly recommend following the step by step
video assembly manual.
!
NOTE:Inorder to avoid injury or damages,
pleasedo not try to assembleyour deskalone.
Our furniture is massiveand heavyand requires
at least two people to carry out assembly.
Pleaseassembleon soft surface to avoid
scratchesto the lacquer.
The Desk You Deserve
Thank you for making StudioDesk your desk of choice!
Before beginning assemblyof your desk,let’s get familiar with the parts you havereceived in your package.
Pleasematch the corresponding numbers on this page with the drawings.
Parts
1. Legs 2. Shelf Holder 3. Cablemanagement/strengthening Bar 4. Desksurface 5. Back/Computer shelf 6. Top
shelf and dividers 7. Pull out parts 8. Rack Rails
5
1
4
6
8
2
OPTIONAL Pull-Out
7
3
Hardware
1
4
8
M6 x 12
Screw
35 pcs
TOOLS needed
2
Washer M6
Confirmat screws
7 x 50 3 pcs
Dowels10/40
18 pcs
3
Hexagon wrench
7 pcs
1pc
5
Metal brackets
5 pcs
6
9
Height controller
1 pcs
10 Rackrails
RGBLED SET
PULLFANTOM#2
FANTOM
Cable inlay (1pc)
Hexagon wrench (1pc)
M6 x 12 screw (16 pcs)
Confirmat screw 7x50 (5 pcs)
Long L bracket (4 pcs)
Plug
EU
US
UK
Cableinlay
3 pc
4 pcs
7 Screw for
wood
6 pcs
11
Cagenuts M6 x 12
16 pcs
Screw Black
16 pcs
www.studiodesk.net
1
Step One Start off by placing the U-profile rods on each side of the bottom of the main
2
Step Two
board so the two larger central holes are facing outward and screw them in
using 3 x M6 screws on each side as shown in the picture.
Place the horizontal support for the main board as
shown in the picture. Beware that the holes on the
U-profiles and the horizontal support align.
8
3
Step Three
Screw in the horizontal support together using 8 x
Hexagon head screws and screw the support to the
main board using 2 x M6 screws as shown. If there
stays a gap between the hexagon screws and the
support, it's normal.
4
Step Four
Place and screw in the motorized legs using 12 x hexagon head screws on each leg. Be
careful that the threads on the legs are facing the front of the desk.
5
Step Five
Place and screw in the base of the motorized leg
using 1 x hexagon head screw on each side like
shown in the picture
6
Step Six
Screw in the desk glides and 4 x hexagon head
screws in each leg as shown in the picture.
7
Step Seven
Install the stabilizing bridge for the legs as shown in the
picture.
8
Step Eight
Insert the controller for the legs into the horizontal support. It
should slide into one of the sides as shown below.
9
Step Nine
Install the long brackets to the desired height of
your pull out as shown in the picture.
The pull out height can be adjustable.
10
Step Ten
Install the pull out sides to the bottom of the
main board using 4 x M6 screws on each side.
11
Step Eleven
Flip the desk onto its legs and install the three
rack dividers into the main board using 2 x
dowels for each divider like shown in the
picture.
12
Step Twelve
Install the back/monitor shelf onto the
dividers by placing 2 dowels in each divider
and push the shelf onto the dowels.
13
Step Thirteen
Fixthe dividers and the monitor
shelf using M6 screws and brackets
on each end of the shelf and the
inside of the divider.
14
Step Fourteen
Install 3 brackets onto the dividers
for the top shelf like shown in the
picture.
15
Step Fifteen
Turn the top shelf upside - down and install
the shelf holders and the height controller
using screws for wood.
16
Step Sixteen
Place the top shelf onto the rack
dividers using 6 dowels like shown in
the picture.
17
Step Seventeen
Fix the top shelf to the rack
dividers by screwing the brackets
into the top shelf like shown in the
picture.
18
Step Eighteen
Fix each rack divider with the main board
using 1 x confirmat screw in each divider
like shown in the picture.
19
Step Nineteen
Install the 6U rack rails using Black M6 screws
like shown in the picture.
20
Step Twenty
Install the strengthening bar/cable management
system using 7 x M6 screws and washers like
shown in the picture.
The next steps are for the pull-out option
21
Step Twenty One
Install the back board onto the pull out main board
using 4 x confirmat screw
22
Step Twenty Two
Insert the keyboard main board evenly to the pull
out rails, making sure that both glides are in the
front position. Push the main board evenly on
both sides into the rails to the end, when its in
place you will hear a click sound.
CONGRATULATIONS YOUR NEW DESK IS READY!
">
