E STA B L I S H E D 1 9 1 0 • F U LTO N , M I SS O U R I
PYTHON
WIRE WINDER
®
Read this entire manual.
1
This safety alert symbol is
used throughout this manual to
call your attention to messages
involving your personal safety
and the safety of others. Failure
to follow these instructions can
result in injury or death.
1WARNING
Si no entiende ingles, se prefiere que
busque a alguien que interprete las
instrucciones para usted.
Owner:
Date Purchased:
Manual #: 9MPYTHONWW2460752
Operator’s Manual
Danuser Machine Company, LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246
E-mail: [email protected]
Website: www.danuser.com
Letter to Owner/Operator
Dear Owner/Operator,
Thank you for purchasing this Danuser Python Wire Winder. We appreciate your
business.
The Python Wire Winder is designed to meet the needs of farmers, ranchers, and fencing
professionals. The Python Wire Winder connects onto a hydraulic auger drive unit and
can wind up to 6 miles of smooth or 3/4 mile of barbed wire into convenient rolls.
Your safety as an operator of our product is very important to us. Therefore, before you
assemble, install, operate, maintain, remove, or move your Danuser Python Wire Winder,
read and understand this manual thoroughly. If there is anything you do not understand,
immediately contact your dealer, or contact our factory direct.
Tel:
E-mail:
(573) 642-2246
[email protected]
Your satisfaction in the performance and longevity of our product is also very important
to us and can be prolonged by proper assembly, installation, operation, and maintenance
as instructed in this manual.
Thank you again for your business and for your trust in our product. Please feel free to
contact us at any time for further assistance.
Sincerely,
Danuser Machine Company, LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246
E-mail: [email protected] Website: www.danuser.com
Danuser provides this manual “as is” without warranty of any kind, either expressed or implied. Danuser
assumes no responsibility for errors or omissions. Danuser assumes no liability for damages resulting
from the use of the information contained herein. Danuser reserves the right to revise and improve its
products as it sees fit. This manual describes the state of this product at the time of its publication and may
not reflect the product in the future.
Danuser is a registered trademark.
Foreword
Symbols
Table of
Contents
Please read this manual thoroughly!
Before you assemble, install, operate, maintain, remove, or move
your Danuser Python Wire Winder, read this manual thoroughly.
If there is anything you do not understand, immediately contact
your dealer, or call our factory direct at (573) 642-2246. Powered
equipment can be dangerous if not assembled, installed, operated,
maintained, removed, or moved properly.
This SAFETY ALERT symbol identifies important safety
messages. Carefully read each safety message that follows.
Failure to understand and obey a safety message, or recognize a
safety hazard, could result in injury or death to you or others around
you. The operator is ultimately responsible for the safety of himself,
as well as others, in the operating area of the wire winder.
1
Symbol
Meaning
1 DANGER
Indicates an imminently hazardous
situation which, if not avoided, will result
in death or serious injury.
1 WARNING
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury, including hazards that are
exposed when guards are removed.
1 CAUTION
Indicates a potentially hazardous situation
which, if not avoided, may result in minor
or moderate injury. It may also be used to
alert against unsafe practices.
3
This is important information for proper
use of this equipment. Failure to comply
may lead to premature equipment failure.
Page
Letter to Owner/Operator�����������������������������������������������������������������2
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Decals & Safety Signs ���������������������������������������������������������������������8
Specifications�����������������������������������������������������������������������������������9
Assembly & Installation�����������������������������������������������������������������10
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Removal & Storage�������������������������������������������������������������������������14
Troubleshooting �����������������������������������������������������������������������������15
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Torque Values Chart�����������������������������������������������������������������������17
Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Python Wire Unroller���������������������������������������������������������������������19
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 6006
3
Safety
1WARNING
Working with unfamiliar equipment can lead to careless injuries.
Read and understand this manual and the manual for your vehicle
before assembling, installing, operating, maintaining, removing, or
moving this wire winder. If there is anything in this manual you
do not understand, contact your dealer or Danuser. The safe use of
this equipment is strictly up to you, the operator. If this wire winder
is used, loaned, or rented by any other person, it is the owner’s
responsibility to make certain that the operator prior to operating:
•
•
Reads and understands the Operator’s Manuals
Is instructed in safe and proper use
There is an entanglement risk if you replace the retaining bolt and/or
spool retention pin with one longer than specified by Danuser. This
improper replacement occurs most often on equipment that is loaned
or rented to someone who has not read the Operator’s Manual and is
not familiar with the wire winder.
4
•
This wire winder is designed to be used in conjunction with a
hydraulic auger drive unit mounted to the front of the vehicle.
The wire winder must be positioned such that all winding
operations, including the wire path, can be easily seen.
•
Do not use the wire winder on a power take-off (PTO) driven
post hole digger.
•
It is the responsibility of the operator to see that no one is within
twenty-five feet (25’) of the wire winder or wire path before and
during wire winder rotation. Do not operate the wire winder
with another person near or in contact with any part of the drive
unit or wire winder. Serious personal injury or death may result
if any attempt is made to assist winding operation by hand.
•
All operators of this attachment must read and understand this
entire manual, paying particular attention to safety messages and
operation instructions, prior to assembling, installing, operating,
maintaining, removing, or moving the wire winder.
•
Please remember it is also important that you read, understand,
and follow the safety signs on the attachment. Clean or replace
all safety signs if they cannot be clearly read and understood.
They are there for your safety as well as the safety of others.
Danuser will furnish new wire winder safety signs upon request
at no charge.
•
All things with moving parts are potentially hazardous. There
is no substitute for a cautious, safe-minded operator who
recognizes potential hazards and follows reasonable safety
practices.
Safety
•
Personal protection equipment including safety glasses, hearing
protection, safety shoes, and gloves are recommended during
assembly, installation, operation, maintenance, removal, or
movement of the wire winder.
•
When the use of hand tools is required to perform any part of
assembly, installation, maintenance, removal, or movement
of the wire winder, be sure the tools used are designed and
recommended by the tool manufacturer for that specific task.
•
Always use two people to handle heavy, unwieldy components
during assembly, installation, maintenance, removal, or
movement of the wire winder.
•
Never place any part of your body where it would be in danger
if movement should occur during assembly, installation,
operation, maintenance, removal, or movement of the wire
winder.
•
Check clearances between vehicle and wire winder, as well as
operator and wire winder, across the full range of loader arms’
operating heights.
•
Only properly trained people should operate this equipment.
Do not allow anyone who has not read this entire manual
and understood the safety rules, safety signs, and operation
instructions to use this wire winder.
•
Never allow children to operate or be around this wire winder.
•
Do not allow riders on the equipment at any time. There is no
safe place for any riders.
•
Never use alcoholic beverages or drugs which can hinder
alertness or coordination while operating this equipment.
Consult your doctor about operating this equipment while taking
prescription or over-the-counter medications.
•
Safe operation of equipment requires the operator’s full
attention. Avoid distractions such as radio headphones, cell
phones, etc. while operating.
•
Before beginning operation, clear the work area of objects
which might be picked up and thrown by or entangled in the
wire and/or wire winder.
•
Before you operate the attachment, check over all pins, bolts,
and connections to be sure all are securely in place. Replace
any damaged or worn parts immediately.
(continued)
5
Safety
•
Never replace the retaining bolt and/or the spool retention pin
with anything other than one that meets the original equipment
manufacturer’s standards and requirements. A longer, or
protruding, fastener is more likely to grab clothing or gloves,
which can result in serious injury or death.
•
Keep all helpers and bystanders twenty-five feet (25’) away
from the operating attachment and the wire path.
•
Keep hands, feet, hair, jewelry, and clothing away from all
moving and/or rotating parts.
•
Never place yourself between the vehicle and the attachment
•
Never position the wire winder by hand or with any tool when
the vehicle is running.
•
Never manually guide wire by hand or with tool.
•
A heavy load can cause instability of the vehicle. Use extreme
care during travel. Slow down on turns and watch out for
bumps. Use all safety devices, including a seat belt, as
recommended in the vehicle operator’s manual.
•
Do not operate the wire winder on steep hillsides. When
winding wire on uneven or hilly terrain, position the vehicle
with the hydraulic auger drive unit uphill. With the hydraulic
auger drive unit downhill, the vehicle could tip when winding
wire. Consult your vehicle operator’s manual for maximum
incline allowable.
•
Always shut off the vehicle engine, remove the key, lower
vehicle arms, and relieve all hydraulic pressure before
dismounting the vehicle. Never leave equipment unattended
with the vehicle running.
•
Never attempt adjustments, service, or repairs while the
attachment is in operation.
•
Never work under equipment supported by hydraulics. Even
with the vehicle shut off, the attachment can suddenly drop if
controls are actuated or if hydraulic lines burst.
•
Store the wire winder on a flat, level surface in an area where
children do not play. Securely block and support the wire
winder.
•
Do not modify the wire winder. Modifications may weaken the
integrity of the wire winder and may impair the safety, function,
life, and performance of the wire winder.
•
When maintaining the wire winder, use only parts that meet
original equipment manufacturer’s standards and requirements.
(continued)
6
Safety
•
Always use care when operating the wire winder. Most
accidents occur because of neglect or carelessness.
(continued)
Safety is a primary concern in the design, manufacture, sale, and
use of the wire winder. Danuser confirms to you, our customer, our
concern for safety.
1 DANGER
Improper operation of this wire winder can cause
serious personal injury or death. Operation
of this wire winder should only be done by a
competent adult acting in compliance with the
Operator’s Manual. Since winding operations are
beyond our control, we disclaim all liability for
any damages, injuries, or death which may result.
2 WARNING
This product can expose you to chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov/product.
7
Decals &
Safety Signs
1 WARNING
Clean or replace all
safety signs if they cannot
be clearly read and
understood.
The Python Wire Winder comes equipped with all safety
signs in place. Their locations are shown in this section.
Read and follow their instructions and ensure their care:
•
Keep safety signs clean and legible at all times.
•
Replace safety signs that are missing, illegible, or
damaged.
To install new safety signs, follow these steps:
1.
Clean the area where the safety sign is to be placed.
2.
Spray a little soapy water on the surface where the
safety sign is to be placed.
3.
Peel the backing from the safety sign and apply it in
the position shown.
4.
Firmly press the safety sign and squeeze out the air
bubbles with a straight edge (e.g., a credit card).
PART NO. CA65
Location: center column
PART NO. 180601
Location: center column
PART NO. DANUSER111
Location: center column
®
®
PART NO. DIG50
Location: upper spool
assembly, top
8
PART NO. DIG51
Location: upper spool
assembly, top
Specifications
Operator's Manual
Direction Terminology
Front
Right
Left
Rear
B
C
A
Python Wire Winder
Overall Width (A)
22"
Overall Height (B)
40.26"
Collar Size (C)
2” Hex
Weight
98 lb.
Wire Capacity
Up to 3/4 mile barbed
Up to 6 miles smooth
9
Assembly &
Installation
1 WARNING
Personal protection
equipment including
safety glasses, hearing
protection, safety
shoes, and gloves are
recommended during
assembly, installation,
operation, maintenance,
removal, or movement of
the wire winder.
1 CAUTION
Always use two people to
handle heavy, unwieldy
components during
assembly, installation,
maintenance, removal,
or movement of the wire
winder.
Prepare the Vehicle
Read and understand the manual for your vehicle before
installing or using the Python Wire Winder. This wire winder
is designed to be used in conjunction with a hydraulic auger
drive unit mounted to the front of the vehicle. The wire
winder must be positioned such that all winding operations,
including the wire path, can be easily seen.
1WARNING
Do not use the wire winder on a power
take-off (PTO) driven post hole digger.
Recommended Tools
•
1-1/8” wrench (2)
STEP 2: Attach wire winder onto a hydraulic auger
drive unit output spindle using bolt PN 10038
(3/4”–10 x 4”, Gr. 8) and nut PN 10041 included
with your drive unit. NEVER use a bolt longer
than 4”.
1WARNING
1 DANGER
10
Box/band cutter
STEP 1: Remove pallet, banding, zip-ties, and any other
packaging materials.
Operation
It is the responsibility of
the operator to see that
no one is within twentyfive feet (25’) of the wire
winder or wire path
before and during wire
winder rotation. Do not
operate the wire winder
with another person
near or in contact with
any part of the drive unit
or wire winder. Serious
personal injury or death
may result if any attempt
is made to assist winding
operation by hand.
•
Before you operate the attachment, check
over all pins, bolts, and connections to be
sure all are securely in place. Replace any
damaged or worn parts immediately.
STEP 1: Prepare wire(s) for winding. Remove wire(s)
from fenceposts, and clear wire path of any
debris, obstructions, or bystanders.
3
The wire winder is not designed to pull wire(s)
directly from fenceposts. Wire(s) must be
removed from posts before winding.
Operation
(continued)
1 WARNING
Personal protection
equipment including
safety glasses, hearing
protection, safety
shoes, and gloves are
recommended during
assembly, installation,
operation, maintenance,
removal, or movement of
the wire winder.
STEP 2: To ensure tight wrapping of the spool, attach
a piece of log chain to the trailing end of the
wire(s). This will provide resistance, keeping
tension on the wire(s). If desired, multiple wires
may be wound simultaneously.
STEP 3: Tie-wires may be used to secure spooled wire.
Feed tie-wire ends through perimeter holes
located in the upper and lower spool assemblies.
Position the tie-wires into the upper spool
assembly grooves. Secure tie-wire ends.
1 WARNING
Safe operation of
equipment requires the
operator’s full attention.
Avoid distractions such
as radio headphones,
cell phones, etc. while
operating.
1 DANGER
Do not allow riders on
the equipment at any
time. There is no safe
place for any riders.
STEP 4: Attach wire(s) to wire winder using the 10 slots
located at the top of the upper spool assembly.
3
Because smooth wire may slip out of the slot,
it may be necessary to use two or more slots to
secure wire(s).
STEP 5: Raise loader arms and position the hydraulic
auger drive unit so the wire winder hangs freely.
Apply down pressure to insert spike into the
ground until the spike plate contacts the ground.
1 DANGER
Never position the wire winder by hand or
with any tool when the vehicle is running.
11
Operation
1 DANGER
(continued)
Before beginning operation, clear the
work area of objects which might be
picked up and thrown by or entangled in
the wire and/or wire winder.
1 WARNING
STEP 6: Activate the vehicle auxiliary hydraulics to
start the wire winder rotating in the clockwise
direction. Increase the speed as required as
wire(s) are wound onto the wire winder.
Keep hands, feet, hair,
jewelry, and clothing
away from all moving
and/or rotating parts.
1 DANGER
Keep all helpers and bystanders twentyfive feet (25’) away from the wire winder
or wire path before and during wire
winder rotation. The wire winder must
be positioned such that all winding
operations, including the wire path, can
be easily seen.
3
Tilting the wire winder toward and away from
the direction of the wire path will allow for even
spooling.
1 DANGER
Never manually guide wire by hand or
with tool.
12
Operation
STEP 7: Once wire is wound, remove log chain. If
tie-wires are used, secure the wound wire.
(continued)
STEP 8: Apply down pressure to insert wire winder spike
fully into the ground, compressing the wire
winder upper and lower spool assemblies and
relieving pressure on retention pin.
STEP 9: Remove spool retention pin, allowing the upper
spool assembly to be lifted free and the wound
wire removed.
1 DANGER
Never place yourself between the vehicle
and the attachment.
3
Store the retention pin in one of the two holes in
the wire winder upper spool assembly.
13
Operation
(continued)
STEP 10: With the wound wire removed, the upper spool
assembly can be reassembled with the lower
spool assembly by lining up the tie-wire holes
on top and bottom, then sliding the lower section
into the upper until the retention pin hole is
visible. Replace the retention pin and rotate to
secure it in place
1 DANGER
Never replace the spool retention pin
with anything other than one that meets
the original equipment manufacturer’s
standards and requirements. A longer, or
protruding, fastener is more likely to grab
clothing or gloves, which can result in
serious injury or death.
Removal &
Storage
1 DANGER
Never allow anyone
under the attachment at
any time.
1 WARNING
Personal protection
equipment including
safety glasses, hearing
protection, safety
shoes, and gloves are
recommended during
assembly, installation,
operation, maintenance,
removal, or movement of
the wire winder.
14
Before storage, the Python Wire Winder should be
thoroughly cleaned, washing off all dirt and grime. Always
store the wire winder in a dry, covered location.
STEP 1: If storing the attachment, lower the hydraulic
auger drive unit and Python onto a flat, level
surface in an area where children do not play.
Follow your vehicle operator’s manual for
removing an attachment. Securely block and
support the attachment.
3
Take care to gently set down the wire winder.
The hydraulic auger drive unit’s weight can
cause the wire winder spool assemblies to bend
if set down improperly.
STEP 2: If storing the Python disconnected from the
hydraulic auger drive unit, remove the retaining
bolt and nut. Separate the wire winder from the
drive unit, and lower it onto a flat, level surface
in an area where children do not play.
STEP 3: Replace any damaged or missing safety signs.
Troubleshooting
Problem
Possible Cause
Wire(s) not winding
evenly
Python not properly tilted while
winding
Refer to Operation.
End of wire(s)
moving erratically
Log chain not in use
Attach log chain to end of
wire(s).
Winding too fast
Reduce engine RPM.
Wire(s) breaking
Obstacles or tall grass snagging
wire(s) while winding
Ensure grass is cut and obstacles
are cleared from wire(s) path.
Retaining bolt and
nut vibrate loose
Improper torquing
Ensure retaining bolt and nut
are torqued properly. See Torque
Values Chart.
Retention pin hard to
remove
Retention pin requires down
pressure to remove
Refer to Operation.
Retention pin cannot
be reinserted
Upper and lower spool
assemblies not aligned
Ensure sections are aligned prior
to reassembly.
Spike not pressed fully into
ground
Apply greater down pressure.
Sandy or loose ground
conditions
If possible, find firmer ground
nearby.
Python comes out
of ground during
operation
Solution
For additional assistance, please call your dealer or contact Danuser direct:
Tel: (573) 642-2246
E-mail: [email protected]
15
Maintenance
1 DANGER
Never work under
equipment supported
by hydraulics. Even
with the vehicle shut
off, the attachment can
suddenly drop if controls
are actuated or hydraulic
lines burst.
1 WARNING
Personal protection
equipment including
safety glasses, hearing
protection, safety
shoes, and gloves are
recommended during
assembly, installation,
operation, maintenance,
removal, or movement of
the wire winder.
Proper maintenance is key to the long life of the wire winder.
Careful inspection and routine maintenance help avoid costly
downtime and repair. Do not use the Python Wire Winder
with any damaged parts.
1 DANGER
Never replace the retaining bolt and/
or spool retention pin with anything
other than one that meets the original
equipment manufacturer’s standards and
requirements. A longer, or protruding,
fastener is more likely to grab clothing or
gloves, which can result in serious injury
or death.
1WARNING
Do not modify the wire winder.
Modifications may weaken the integrity of
the wire winder and may impair the safety,
function, life, and performance of the wire
winder.
Maintenance
Inspect the attachment for any damage or worn
parts. Repair or replace as necessary.
Check for damaged or missing safety signs.
Replace as necessary.
Visually inspect all welds for cracks. Check all
bolts and fasteners for tightness.
Inspect upper and lower spool plates for damage.
Inspect lower assembly for bending.
16
Interval
Before each use
Before each use
Before each use
Before each use
Torque Values
Chart
Torque Values Chart
Bolt Head Identification
Bolt Size
(inches)
Grade 2
Bolt Head Identification
Grade 5
Grade 8
ASTM A574
Bolt Size
(Metric)
5.8
8.8
8.8
10.9
10.9
12.9
12.9
Class 5.8
Class 8.8
Class 10.9
Class 12.9
in tpi
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb. mm x pitch
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
Nm
1/4” 20
7.4
5.6
11
8
16
12
19
14
M5 x 0.8
4
3
6
5
9
7
11
ft.-lb.
8
1/4” 28
8.5
6
13
10
18
14
22
16
M6 x 1
7
5
11
8
15
11
18
13
5/16” 18
15
11
24
17
33
25
39
29
M8 x 1.25
17
12
26
19
36
27
42
31
5/16” 24
17
13
26
19
37
27
43
32
M8 x 1
18
13
28
21
39
29
46
34
62
3/8” 16
27
20
42
31
59
44
69
51
M10 x 1.5
33
24
52
39
72
53
84
3/8” 24
31
22
47
35
67
49
79
58
M10 x 0.75
39
29
61
45
85
62
98
72
7/16” 14
43
32
67
49
95
70
110
81
M12 x 1.75
58
42
91
67
125
93
148
109
7/16” 20
49
36
75
55
105
78
123
91
M12 x 1.5
60
44
95
70
130
97
153
113
1/2” 13
66
49
105
76
145
105
168
124
M12 x 1
90
66
105
77
145
105
167
123
1/2” 20
75
55
115
85
165
120
190
140
M14 x 2
92
68
145
105
200
150
235
173
9/16” 12
95
70
150
110
210
155
235
173
M14 x 1.5
99
73
155
115
215
160
254
187
9/16” 18
105
79
165
120
235
170
262
193
M16 x 2
145
105
225
165
315
230
365
269
5/8” 11
130
97
205
150
285
210
323
238
M16 x 1.5
155
115
240
180
335
245
388
286
5/8” 18
150
110
230
170
325
240
366
270
M18 x 2.5
195
145
310
230
405
300
504
372
3/4” 10
235
170
360
265
510
375
574
423
M18 x 1.5
220
165
350
260
485
355
561
414
3/4” 16
260
190
405
295
570
420
640
472
M20 x 2.5
280
205
440
325
610
450
712
525
7/8” 9
225
165
585
430
820
605
925
682
M20 x 1.5
310
230
650
480
900
665
1052
776
7/8” 14
250
185
640
475
905
670
1020
752
M24 x 3
480
355
760
560
1050
780
1231
908
1” 8
340
250
875
645
1230
910
1386
1022
M24 x 2
525
390
830
610
1150
845
1337
986
1” 12
370
275
955
705
1350
995
1555
1147
M30 x 3.5
960
705
1510
1120
2100
1550
2447
1805
1-1/8” 7
480
355
1080
795
1750
1290
1971
1454
M30 x 2
1060
785
1680
1240
2320
1710
2706
1996
1-1/8” 12
540
395
1210
890
1960
1440
2202
1624
M36 x 3.5
1730
1270
2650
1950
3660
2700
4272
3151
1-1/4” 7
680
500
1520
1120
2460
1820
2771
2044
M36 x 2
1880
1380
2960
2190
4100
3220
5095
3758
1-1/4” 12
750
555
1680
1240
2730
2010
3068
2263
1-3/8” 6
890
655
1990
1470
3230
2380
3638
2683
1-3/8” 12
1010
745
2270
1670
3680
2710
4143
3056
1-1/2” 6
1180
870
2640
1950
4290
3160
4823
3557
1-1/2” 12
1330
980
2970
2190
4820
3560
5426
4002
KEY:
in tpi = nominal thread diameter in inches threads per inch
Nm = Newton-meter
ft.-lb. = foot pounds
mm x pitch = nominal thread diameter in millimeters by thread pitch
Torque tolerance +0%, -15% of torque values. Unless otherwise specified, use torque values listed above.
17
Parts
2 WARNING
This product can expose you to chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov/product.
1
3
2
REF. NO.
PART NO.
1
170611
Upper Spool Assembly
1
2
170612
Lower Spool Assembly
1
3
170626
Spool Retention Pin
1
18
DESCRIPTION
QTY.
Accessories
Auger Adapter
Python Wire
Unroller
Python Wire Unroller
PN 10923 - Allows Python to connect onto 2-9/16” round
output spindles with 7/8” bolt hole. Not for use with power
take-off (PTO) driven post hole diggers.
PN 180606 - The Python Wire Unroller connects onto a 2”
receiver hitch and accepts pre-wound wire or bundles wound
using the Python Wire Winder.
19
Warranty
DANUSER
LIMITED WARRANTY
Danuser Machine Company, LLC (“Danuser”) warrants its products, under normal use and maintenance, to be
free from defects in material and workmanship for period(s) specified below from the purchase date from an
authorized Danuser Dealer. Start of the warranty period is determined by purchase date. Proof of purchase may
be required. This Limited Warranty is extended only to the original purchaser of Danuser products.
Python Wire Winder - 1 Year
1.
During the applicable warranty period, Danuser, at its option, will repair or replace any part determined
by Danuser to be defective. Such repair or replacement shall take place at Danuser’s factory, or a location
designated by Danuser. Under no circumstances shall Danuser be obligated for the cost of any repair or
replacement by anyone other than Danuser without its express written consent.
2.
Parts may not be returned without written authorization from Danuser.
3.
Some purchased components, including but not limited to hydraulic components, are subject to the
inspection and warranty of the respective manufacturer. Thus, delays in a warranty determination can be
expected while Danuser awaits their decision.
4.
This warranty is void if any attempt is made to make field repairs to hydraulic components. To qualify for
warranty inspection, the “failed” part(s) must be returned in its original “failed” condition.
5.
To make a claim under this warranty, first contact your authorized Danuser Dealer. The Danuser Dealer
shall complete the Warranty Claim Form and obtain written authorization from Danuser to return parts.
All warranty claims must include detailed information regarding make and model of vehicle on which the
Danuser product was mounted, hours of use, description of events that led up to the failure, and any other
information helpful in reviewing the warranty claim. All warranty returns must be prepaid. Shipments
arriving at our factory on a freight collect basis will be refused by our receiving department. The freight
charge will be credited if the parts are determined by Danuser to be defective, and the associated freight costs
in returning those parts will be prepaid by Danuser. NOTE: Hydraulic components must arrive with all ports
sealed from dirt and moisture. If a hydraulic component arrives with open ports, the warranty is void and no
inspection will be made.
6.
Products or parts thereof which, as determined by Danuser’s examination, show wear from normal use,
have been improperly operated, damaged by accident or negligence, field repaired, altered or modified are
not considered defective in material and workmanship and are not covered by this warranty. This warranty
does not apply to parts subject to normal wear (“Wear Items”) or to damage caused by the failure to perform
recommended maintenance or to replace worn parts. This warranty shall not obligate Danuser to bear any
cost of labor for field repair, replacement, testing, or adjustment nor for damage caused by accident, abuse,
misuse, or environmental elements.
7.
Any parts or labor required to repair or replace parts not covered under this warranty will be charged to the
customer. Parts repaired or replaced by Danuser are then covered by this warranty only for the remainder of
the original warranty as if such parts were original parts.
8.
Danuser reserves the right to change its specifications and designs at any time.
This warranty is exclusive and in lieu of all other express warranties, if any, including the implied warranties
of merchantability and fitness for a particular purpose. It shall not extend beyond the duration of the expressed
warranty provided herein and the remedy for violations of any implied warranty shall be limited to repair or
replacement of the defective part pursuant to the terms contained herein. No employee, dealer, salesman, or
representative is authorized to change this warranty in any way or grant any other warranty. Danuser shall not be
liable for any consequential, incidental, or punitive damages, losses, or expenses, including those resulting from
or caused by any defects.
Danuser Machine Company, LLC
500 E. 3rd St
P.O. Box 368
Fulton, MO 65251
Tel:
E-mail:
Website:
(573) 642-2246
[email protected]
www.danuser.com
PD 6006
">
