Legrand Contain-IT FLEX Installation Instructions

125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Contain-IT™ FLEX Install Guide
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
1 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Table of Contents:
Introduction
Necessary Tools
Items not Included
Torques
General Rule
Getting Started
Typical Sequences of Operations
Beam Position
Flap and Bulb Seal
Panels
Panels and Panel Clips
How to Form a Corner Panel
Beam Splice
Alternate Method of Splicing Beams
(Beam) Hanger
Cabinet Bracket
Horizontal Containment Against a Building Wall
Corners
Vertical Blanking Panels
Vertical Obstructions
Horizontal Obstructions
Standard sized 2' x 4' ceiling tiles
Table: Horizontal Aisle Kit Component Quantities
Table: 4' Vertical Aisle Kit Component Quantities
Table: 8' Vertical Aisle Kit Component Quantities
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
2 of 34
DWN BY:
RA
DATE:
02/10/2017
3
3
3
4
4
4
5
6‐8
9‐10
11‐12
13
14
15
16
17‐20
21‐22
23
24‐25
26‐27
28‐29
30
31
32
33
34
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Please review this entire guide before beginning the installation. Due to the nature of the
content, details relevant to particular operations may be included in other sub-sections of
the document.
See Applications Guide:
The Contain-IT™ FLEX Applications Guide contains the following information not included
in this document:
•
How to determine aisle type
•
How to measure aisles
•
How to determine what to order
•
A detailed pictorial list of components
•
Product weight and auxiliary load carrying capacity
•
Flammability and smoke ratings
See End of Row Door Installation Instructions:
Please see document number OR-71601934 for end of row door installation instructions
Necessary Tools:
•
•
•
•
T10 Torx driver (a T10 Torx 1/4" hex shank driver bit is supplied with each kit of screws)
#3 Phillips driver (a #3 Phillips 1/4" hex shank driver bit is supplied with each kit of screws)
Tape measure
Chop saw (for cutting Beams to length)
•
Hand saw with miter box
•
A hand saw with miter box is available from Legrand P/N OR-CFTKIT
•
Powered miter saw with finish blade
Finish saw (for cutting Panels)
•
Fine tooth hand saw capable of cutting 3/8" thick, 48" wide, hollow, plastic Panels
•
Jig saw with plastic or plexi blade
•
Circular saw with finish or paneling blade
Two 3/4" open end wrenches
•
Adjustable wrenches that open to 3/4" are acceptable
Shop shears or heavy duty scissors
Level
Framing square
Drywall square, 48" straight edge or chalk line
Step Ladder
Personal Protective Equipment appropriate for tools used, including safety glasses
•
•
•
•
•
•
•
•
Items not included in kits:
•
Threaded rod (with washers and nuts)
•
The recommended (and largest size) threaded rod is 1/2"-13
Cage nuts and screws for securing Cabinet Brackets to cabinet tops
•
The part numbers for #12-24 cage nuts and screws quantity 50 of each are:
•
Cage nuts: OR-PS-1224CN, Screws OR-60400533
Screws/bolts, washers and nuts needed to lock containment to Cablofil wire mesh cable
tray
•
•
Torques for fasteners:
•
•
•
•
#4 fasteners in plastic connectors: 3 inch•pounds
#12 fasteners in plastic Beams: 5 inch•pounds
#12 fasteners in aluminum Beams: 25 inch•pounds
1/2"-13 nut on threaded rod on Hanger: 25 inch•pounds
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
3 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
General Rules:
•
•
•
•
•
•
•
Every Beam that runs along the aisle that is greater than 36 inches in length requires
two means of support
Every Beam that runs along the aisle that is greater than 18 inches in length requires at
least one means of support
•
There are two different means of support: Hangers and Cabinet Brackets
•
For Beams with a single means of support, the support must be located at the
center of gravity
The nominal distance between supports is 45 inches
•
The 45 inch spacing corresponds to half the length of the beams, which are 90
inches long
The maximum spacing between means of support is 72 inches
The flutes of the Panels must go across the aisle for Horizontal Containment and must
be oriented vertically for Vertical Containment
End of Row Doors may be installed before or after Containment
•
Consider accessibility to Containment and potential of damage to Doors when
deciding whether to install Doors before or after Containment
•
End of Row Doors may impede ladder and/or lift placement or pathways
Ensure all Beams are level and all corners are square
Getting Started:
•
•
Verify receipt of all parts
•
Verify that all part numbers that were purchased were received
•
Verify that all components of items purchased were received
•
See the "Aisle Kit Component Quanities" tables at the end of this
document for quantities of components in each kit
Determine the position of the lower Beam; in the case of Horizontal Containment,
the lower Beam is the only Beam
•
The lower Beam is typically (but not necessarily) set a nominal distance above
the tallest cabinet
•
If the majority of the cabinets are not as tall as the tallest cabinet, it may
be more efficient to treat the tallest cabinet as a horizontal obstruction
Tallest cabinet treated as a
horizontal obstruction
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
4 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Typical Sequence of Operations, Horizontal:
1.
2.
3.
4.
5.
6.
Install means of support, either Cabinet Brackets (OR-CFBC) or Hangers (OR-CFBHB8)
on threaded rod (or Cablofil wire mesh cable tray)
Install Beams (OR-CFB90A or OR-CFB90P) that go along aisle (above cabinets, if
cabinets are present at the time of installation), including Beam Splices (OR-CFSB4)
and #4 Screws (OR-CFHWTRX) that secure them
1.
Installation of Beams that go along aisle may require cutting one or more Beams
to length
Cut Panels (OR-CFPMW48108), Panel Splices (OR-CFSP3108) and cross Beams (ORCFB90A or OR-CFB90P) to length
Install Panels, Panel Splices, and cross Beams concurrently, working from the middle of
the aisle toward the ends
1.
Installation of cross Beams inside the aisle uses Inside Corners (OR-CFCI4)
2.
The two end cross Beams use Inside Corners and Outside Corners (OR-CFCO4)
Install Corner Support Brackets (OR-CFCSB4) on all cross Beams
Install Panel Clips (OR-CFRC12), Flap Seals (OR-CFSC96), and Badges (OR-CFCAP4), in
no particular order
Details for each individual step listed above are contained in other sub-sections of this
document.
Typical Sequence of Operations, Vertical:
1.
2.
3.
4.
5.
6.
7.
Install means of support, either Cabinet Brackets (OR-CFBC) or Hangers (OR-CFBHB8)
on threaded rod (or Cablofil wire mesh cable tray)
Install Beams (OR-CFB90A or OR-CFB90P) that go along aisle (above cabinets, if
cabinets are present at the time of installation), including Beam Splices (OR-CFSB4)
and #4 Screws (OR-CFHWTRX) that secure them
1.
Installation of Beams that go along aisle may require cutting one or more Beams
to length
2.
It may be advantageous, but is not necessary, to install the upper Beams before
the lower Beams, due to accessibility issues that the lower Beams may create
1.
The accessibility issues that the lower Beams may create would be relative
to ladder/lift placement/pathways
2.
It is not possible to install upper Beams first in cabinet supported
configurations
3.
It may be advantageous, but is not necessary, to install the Bulb Seals (ORCFBS296) into the upper Beams before installing the upper Beams
Cut cross Beams to length and install them
1.
Installation of cross Beams inside the aisle uses Inside Corners (OR-CFCI4)
2.
The two end cross Beams use Inside Corners and Outside Corners (OR-CFCO4)
Cut Panels (OR-CFPMW4848) and Panel Splices (OR-CFSP348) to height, if Panel
Splices are going to be used
1.
The alternative to Panel Splices is overlapping Panels
Form four corner Panels using Panels that were previously cut to height
Install Panels
Install Panel Clips (OR-CFRC12), Flap Seals (OR-CFSC96), and Badges (OR-CFCAP4), in
no particular order
Details for each individual step listed above are contained in other sub-sections of this
document.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
5 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Beam Horizontal Position:
3.0"
Minimum
Beam
Flap Seal
PRESSURE
AISLE
Cabinet
Cabinet
Recommended Beam Horizontal Position: Positive or Negative Pressure
.5"
Minimum
Beam
Flap Seal
PRESSURE
PRESSURE
AISLE
Cabinet
Cabinet
Narrow Beam Horizontal Position: Negative Pressure Only
Beam Orientation:
Plastic
Beam
TOP
TOP
BOTTOM
BOTTOM
Aluminum
Beam
Beams shall be oriented as shown above, except when specifically stated otherwise.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
6 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Beam Vertical Position:
CEILING
1.75" MAX
.5" MIN
Bulb Seal
Beam
Vertical position of upper Beam in vertical containment.
Cabinet
Bracket
Beam
Badge
.5"
CABINET TOP
Outside
Corner
4.0"
CABINET TOP
The height range for the bottom Beam, using Flap Seal is shown above (Flap Seal is
not shown). This height range also applies to ceiling supported containment
(Hangers not shown).
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
7 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Beam Position:
•
The lower Beam may be positioned over or inside of the End of Row Door, as shown
below.
•
The same dimensions that apply to the Flap Seal relative to a cabinet apply
here.
•
The same dimensions that apply to the Bulb Seal relative to a ceiling apply
here.
Beam
The Bulb Seal
must make
contact with
the inside of the
End of Row
Door
The Flap Seal must
drop vertically on
top of End of Row
Door
Flap Seal
"Y" > 0
"Z" > 0
"X" > 0
End of Row
Door
End of Row
Door
Beam
Bulb Seal
AISLE
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
8 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Flap Seal and Bulb Seal:
•
•
•
By default, the Flap Seal and Bulb Seal should be cut 6 inches longer than the beam
into which it is being installed.
•
The additional 6 inches of length of the Flap Seal is to allow it to overlap, to avoid
leaks that are created by butt joints.
•
The additional length of Bulb Seal is to allow it to be slit and inserted into the
adjacent Bulb Seal, again to avoid leaks that are created by butt joints.
•
On long runs, the number of pieces of Flap Seal and/or Bulb Seal that are needed
are the same as the number of lower/upper Beams. The Flap Seal and Bulb Seal
are 96 inches long; the Beams are 90 inches long.
To install the Flap Seal, slide Beam Splices (OR-CFSB4) onto the Flap Seal from the ends,
with the Beam Splices located 12 inches in from each end and roughly evenly spaced
in between.
Once the Beam Splices are positioned on the Flap Seal, snap the Beam Splices into the
Beam where needed.
Beam
Panel Splice
Flap Seal
Panel Splice
Flap Seal
INSTRUCTION SHEET #:
OR-71601931
REV:
00
Beam
ECN #:
SHEET:
9 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Bulb Seal:
The Bulb Seal is installed by compressing the ribs, and pushing the smaller bulb into the
beam.
Squeeze & Push
Bulb Seal
Beam
The Bulb Seal may be installed in any of the four positions in the Beam, as shown above.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
10 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
TITLE:
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
Panels:
Vertical Panels:
•
Contain-IT™ FLEX Install Guide
The height of vertical Panels is 1.5 inches greater than the distance between the
Beams.
Beam
Panel
Beam to Beam
Beam
Horizontal Panels:
•
The width of the horizontal Panels is 1.3 inches greater than the distance between the
Beams.
Beam
to
Beam
Panel
Beam
Beam
Overlapped Panels:
•
•
The nominal overlap between Panels should be 6 inches.
The minimum overlap between Panels is 3 inches.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
11 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
TITLE:
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
Contain-IT™ FLEX Install Guide
Panels:
Overlap:
3.0" minimum
6.0" nominal
OR-CFSP3XX Panel Splice in
an unistalled state
Minimum
engagement
Full insertion
OR- CFSP3XX
installed
.38"
5/8"
Panel Splice (OR-CFSP3XX)
•
Panels may fully inserted or engaged as little at 3/8"
•
Panel Splice adds 5/8" to width of each panel
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
12 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Installation of Panels and Panel Clips:
Beam
Squeeze
Insert top of
Panel into
upper Beam
Panel Clip
Squeeze
Panel
Squeeze
Swing bottom
of Panel over
lower Beam
and drop in
Squeeze
Beam
Use four Panel Clips per 4 foot wide panel; two in top Beam and two in bottom Beam.
Or, two in left Beam and two in right Beam for horizontal containment.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
13 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
To Form Corner Panels:
•
To form a corner Panel:
•
Place a Panel on a straight edge of a table or workbench (or other similar
object, such as a crate)
•
Align the Panel with the desired leg width extending over the straight edge
•
Make sure that the straight edge does NOT cross flutes.
•
Hold the entire length of the Panel down on the table, and press down on the
entire length of leg
•
Panels longer than 24 inches will require two people
Hold down along entire
length of Panel
Press down along entire
length of Panel
Leg
Width
TABLE
Corner of straight
edge in middle of
flute: DO NOT
CROSS FLUTES
Leg
Width
12" TO 24"
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
14 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Beam Splice:
#4 Screw
Beam Splice
Beam
Beam Splices may be snapped in or slid in from end. Joints are secured with #4 screws.
Torque: 3 inch•pounds
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
15 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Alternate Splicing Method:
An alternate method of splicing is to use two Inside Corners on the end of a perpendicular
Beam that aligns with seam.
Beam Splice and Inside Corners are secured with #4 screws.
Torque: 3 inch•pounds
Beam Splice
Beam
Inside Corner
#4 Screw
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
16 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Hanger:
For Horizontal Containment, hangers and cabinet brackets must be installed outside the
aisle.
The hangers and cabinet brackets must be installed outside the aisle, because the
hangers and cabinet brackets will interfere with the Panels.
For Vertical Containment, Hangers and Cabinet Brackets may be installed inside or
outside the aisle.
Beam
Hanger
Push
here
Hook here
Hangers may either be snapped on OR slid on from the end of the Beam.
#12 Screw
Hangers are secured to Beams using #12 screws, which are provided.
Torque in plastic Beam 5 inch•pounds
Torque in aluminum Beam 25 inch•pounds
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
17 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Hanger:
Threaded rod
Hanger
2.4"
Beam
Hanger may be snapped on to Beam around the threaded rod, as shown above.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
18 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Hanger:
Hook one end
Push
opposite
end
Push
oppsite
end
Hook one end
Hanger
Cablofil
Both ends
engaged
Both ends
engaged
Hangers may be used to mount to Cablofil tray, as shown above and below.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
19 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Hanger:
Hanger
Cablofil
Threaded rod
To lock the Hanger to
the Cablofil: use a 1/4" x
1" screw/bolt, two flat
washers & nylon locking
nut, twice per Hanger
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
20 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Cabinet Bracket:
•
•
•
The Cabinet Bracket is secured to the cabinet frame with cage nuts and screws (not
provided in the aisle kit),as shown above and below
The Beam is secured to the Cabinet Bracket with #12 screws (OR-CFHWPHPS, which are
provided in the aisle kit)
•
Torque for plastic Beam is 5 inch•pounds, aluminum Beam is 25 inch•pounds
The Cabinet Bracket may be installed with the foot facing away from the Beam, as
shown on this sheet or with the foot under the Beam, as shown on the next sheet
Cabinet Bracket
Beam
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
21 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Cabinet Bracket:
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
22 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Horizontal Containment Against a Building Wall:
To install Horizontal Containment against a building wall, it is is necessary to rotate the
Beam that will be installed against the wall 90°, as shown below
Cabinet
Bracket: up
Building Wall
Cabinet
Bracket: down
Cut away end view
Cut away
view
Building Wall
Cabinet Bracket
mounts to the
building wall: it may
be mounted up or
down
Beam rotated 90°
Beam mounts to
the top of the
Cabinet Bracket
and secured with
#12 screws
Bulb Seal forms a seal
against the the wall
Enlarged cut away end view
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
23 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Corners:
•
•
•
Beams are cut to align vertices at corner as shown. The Outside Corner (ORCFCO4) connector sets this relationship
Plastic corner connectors (OR-CFCI4 and OR-CFCO4) are secured with #4 screws
(OR-CFHWTRX)
•
Torque: 3 inch•pounds
The Badge(OR-CFCAP4) is installed by pushing the barbs into the outside corner
Outside
Corner
Beam
Badge
#4 Screw
Inside
Corner
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
24 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Corners:
•
•
•
For Horizontal Containment, the position of the Panels make screws on Inside Corner (ORCFCI4) connectors inaccessible
When screws on Inside Corner connectors are inaccessible, Corner Support Brackets (ORCFCSB4) are used
•
They are fastened to Beams by installing #12 screws (OR-CFHWPHS) into grooves, as
shown
The intersections between cross Beams and Beams that run along aisles are treated as
inside corners
Panel
Beam
Corner
Support
Bracket
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
25 of 34
#12 Screw
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Vertical Blanking Panels:
Use (OR-CFCI4) Inside Corners
to hold assembled Blanking
Panel in place while
attaching it to Containment
Cut vertical Beams the
same dimension as the
Containment Beam
measures from the floor
Cut the vertical Bulb Seals
7/8" longer than the
vertical Beams; this fills
channels in Containment
above filler panel
Install 8 Panel
Clips (ORCFRC12) per
pane (not
shown)
Install the lower horizontal
Beam 1.5" up from the extent
of the vertical Beam; this
allows space for Bulb Seal
Panel width is
8.5" less than
opening width
Cut horizontal Beams 10"
less than the opening size
Cut the bottom Bulb Seal 1.75"
longer than horizontal Beam:
this fills the channels
in both vertical Beams
Maximum opening width using
a 48" wide Panel = 56"
Use four (OR-CFBSF4) Flat Bracket Kits to assemble
panel panes (two near side, two far side);
secure brackets with #12 Screws (OR-CFHWPHPS)
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
26 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Vertical Blanking Panels:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Cut both Panels to width
Assemble the lower pane of the Blanking Panel, and assemble the lower Flat
Brackets on the upper pane
Measure and cut upper pane to height
Install the Bulb Seals
Install the upper Panel into the upper Pane
Insert Inside Corners into upper pane
Snap Inside Corner up into the Containment Beam above it
Secure the Blanking Panel to the Containment Beam using Flat Brackets (OR-CFBSF4)
and #12 Screws (OR-CFHWPHPS)
Secure Blanking Panel to the floor as shown below
Existing Containment
Beam
Step seven
Step two
Use Anchor Bracket Kit (OR-CFAB2) and #12 Screws (OR-CFHWPHPS) to secure
panel to floor, as shown above.
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
27 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
TITLE:
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
Contain-IT™ FLEX Install Guide
Vertical Obstruction:
12.38" Minimum
8.0"
12.38"
Minimum Minimum
Length of Beam:
Beam should extend past
obstruction by 1.5"
5.0"
Minimum
obstruction
width
Length of Beam:
obstruction plus 3"
6.5"
Minimum
obstruction
depth
Stop/cut Beams
3.5" shy of
obstruction,
both sides
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
28 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Vertical Obstruction:
On a vertical obstruction, a
seal can be made above or
on the sides
To go around a vertical obstruction, the
following materials are needed:
Bulb Seal
Two Inside Corner Kits (OR-CFCI4)
Two Outside Corner Kits (OR-CFCO4)
One Hanger Kit (OR-CFBHB8)
Two Cap/Badge Kits (OR-CFCAP4),
optional
Adequate length of Beams (ORCFB90x)
Adequate length of Flap Seal (ORCFSC96)
Adequate number of Beam Splice Kits
(OR-CFSB4) to install flap seal
Adequate length of Bulb Seal (ORCFBS296)
Adequate number of Panels (ORCFPMW4848)
One #12 Screw Kit (OR-CFHWPHPS)
One #4 Screw Kit (OR-CFHWTRX)
Outside Corner
Inside Corner
On a vertical obstruction, a
seal can be made below or
on the sides
Flap Seal
Panels not shown for clarity
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
29 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
Horizontal Obstruction:
Inside Corner
Length of Beam:
Obstruction plus 5.5"
Flap Seal and Beam Splices
Inside Corner
Inside Corner
Inside Corner
Bulb Seal
Flat Bracket (OR-CFBSF4), 4
places, installed w/ #12
screws
To go around a horizontal obstruction, the
following materials are needed:
Two Inside Corner Kits (OR-CFCI4)
One Flat Bracket Kit (OR-CFBSF4)
Adequate length of Beams (OR-CFB90x)
Adequate length of Flap Seal (OR-CFSC96)
Adequate number of Beam Splice Kits (ORCFSB4) to install flap seal
Adequate length of Bulb Seal (OR-CFBS296)
Adequate number of Panels (ORCFPMW4848)
One #12 Screw Kit (OR-CFHWPHPS)
One #4 Screw Kit (OR-CFHWTRX)
Beam height:
distance to top of
obstruction
plus 0.5" minimum
Flap Seal will
seal down to
4.5" below
Beam
Minimum height of Beam: 4"
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
30 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
2' x 4' standard or Drop Out ceiling
tiles may be installed in this system,
using the dimensions below.
47.0"
Beam
to
Beam
22.6"
Beam to Beam
46.6"
Beam to Beam
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
31 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
TITLE:
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
Contain-IT™ FLEX Install Guide
Aisle Kit Part number
OR‐CFPMW48108 ‐ MULTIWALL PANEL 48" X 108"
OR‐CFCI4 ‐ INSIDE CORNER, KIT OF 4
OR‐CFCO4 ‐ OUTSIDE CORNER KIT OF 4
OR‐CFRC12 ‐ PANEL CLIP, KIT OF 12
OR‐CFCAP4 ‐ CAP LOGO, KIT OF 4
OR‐CFBHB8 ‐ HANGER, KIT OF 8
OR‐CFBC ‐ CABINET BRACKET, EACH
OR‐CFSB4 ‐ BEAM SPLICE, KIT OF 4
OR‐CFHWPHS ‐ KIT SCREW #12‐1/2 PHILLIPS QTY 50 W/ BIT
OR‐CFHWTRX ‐ KIT SCREW #4‐1/2 TORX ZINC QTY 100 WITH BIT
OR‐CFSP3108 ‐ H PROFILE PANEL SPLICE, 108"
OR‐CFB90P ‐ BEAM, CONTAINMENT, PLASTIC 90"
OR‐CFB90A ‐ BEAM, CONTAINMENT, ALUMINUM 90"
OR‐CFSC96 ‐ FLAP SEAL, 96"
OR‐CFCSB4 ‐ CORNER SUPPORT BRACKET, KIT OF 4
Horizontal Aisle Kit Component Quantities:
OR‐CFHZA415CSA
OR‐CFHZA415CSP
OR‐CFHZA415RSA
OR‐CFHZA415RSP
OR‐CFHZA420CSA
OR‐CFHZA420CSP
OR‐CFHZA420RSA
OR‐CFHZA420RSP
OR‐CFHZA430CSA
OR‐CFHZA430CSP
OR‐CFHZA430RSA
OR‐CFHZA430RSP
OR‐CFHZA440CSA
OR‐CFHZA440CSP
OR‐CFHZA440RSA
OR‐CFHZA440RSP
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
2
2
2
2
3
3
3
3
4
4
4
4
6
6
6
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
2
2
0
0
3
3
8
8
0
0
12
12
0
0
16
16
0
0
24
24
0
0
8
8
8
8
10
10
10
10
14
14
14
14
20
20
20
20
2
2
2
2
2
2
2
2
3
3
3
3
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
0
7
0
7
0
10
0
10
0
13
0
13
0
19
0
19
7
0
7
0
10
0
10
0
13
0
13
0
19
0
19
0
6
6
6
6
8
8
8
8
10
10
10
10
14
14
14
14
2
2
2
2
3
3
3
3
4
4
4
4
6
6
6
6
Horizontal Aisle Kit Part Numbers:
OR-CFHZA _
__
_S
_
Beam material: A = aluminum, P= plastic
Support style: R = roof, C= cabinet
Aisle length (feet)
Aisle width(feet)
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
32 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
OR‐CFCI4 ‐ INSIDE CORNER, KIT OF 4
OR‐CFCO4 ‐ OUTSIDE CORNER KIT OF 4
OR‐CFRC12 ‐ PANEL CLIP, KIT OF 12
OR‐CFCAP4 ‐ CAP LOGO, KIT OF 4
OR‐CFBHB8 ‐ HANGER, KIT OF 8
OR‐CFBC ‐ CABINET BRACKET, EACH
OR‐CFSB4 ‐ BEAM SPLICE, KIT OF 4
OR‐CFHWPHS ‐ KIT SCREW #12‐1/2 PHILLIPS QTY 50 W/ BIT
OR‐CFHWTRX ‐ KIT SCREW #4‐1/2 TORX ZINC QTY 100 WITH BIT
OR‐CFSP348 ‐ H PROFILE PANEL SPLICE, 48"
OR‐CFB90P ‐ BEAM, CONTAINMENT, PLASTIC 90"
OR‐CFB90A ‐ BEAM, CONTAINMENT, ALUMINUM 90"
OR‐CFSC96 ‐ FLAP SEAL, 96"
OR‐CFBS296 ‐ BULB SEAL, 96"
OR‐CFVTA415CSA
OR‐CFVTA415CSP
OR‐CFVTA415RSA
OR‐CFVTA415RSP
OR‐CFVTA420CSA
OR‐CFVTA420CSP
OR‐CFVTA420RSA
OR‐CFVTA420RSP
OR‐CFVTA430CSA
OR‐CFVTA430CSP
OR‐CFVTA430RSA
OR‐CFVTA430RSP
OR‐CFVTA440CSA
OR‐CFVTA440CSP
OR‐CFVTA440RSA
OR‐CFVTA440RSP
OR‐CFPMW4848 ‐MULTIWALL PANEL 48" X 48"
Aisle Kit Part number
4' Vertical Aisle Kit Component Quantities:
12
12
12
12
14
14
14
14
20
20
20
20
26
26
26
26
8
8
4
4
10
10
6
6
16
16
8
8
22
22
12
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
5
5
5
5
6
6
6
6
8
8
8
8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
4
4
4
4
6
6
6
6
8
8
0
0
12
12
0
0
16
16
0
0
24
24
0
0
8
8
8
8
12
12
12
12
16
16
16
16
24
24
24
24
2
2
2
2
3
3
2
2
4
4
3
3
6
6
4
4
1
1
1
1
2
2
1
1
2
2
2
2
3
3
2
2
8
8
8
8
10
10
10
10
16
16
16
16
20
20
20
20
0
18
0
14
0
24
0
20
0
34
0
26
0
46
0
38
18
0
14
0
24
0
20
0
34
0
26
0
46
0
38
0
6
6
6
6
8
8
8
8
10
10
10
10
14
14
14
14
6
6
6
6
8
8
8
8
10
10
10
10
14
14
14
14
Vertical Aisle Kit Part Numbers:
OR-CFVTA _
__
_S
_
Beam material: A = aluminum, P= plastic
Support style: R = roof, C= cabinet
Aisle length (feet)
Aisle height(feet)
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
33 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
125 EUGENE O'NEILL DRIVE
NEW LONDON, CT 06320
TEL: 860-445-3800
FAX: 860-405-2990
WWW.ORTRONICS.COM
TITLE:
Contain-IT™ FLEX Install Guide
OR‐CFCI4 ‐ INSIDE CORNER, KIT OF 4
OR‐CFCO4 ‐ OUTSIDE CORNER KIT OF 4
OR‐CFRC12 ‐ PANEL CLIP, KIT OF 12
OR‐CFCAP4 ‐ CAP LOGO, KIT OF 4
OR‐CFBHB8 ‐ HANGER, KIT OF 8
OR‐CFBC ‐ CABINET BRACKET, EACH
OR‐CFSB4 ‐ BEAM SPLICE, KIT OF 4
OR‐CFHWPHS ‐ KIT SCREW #12‐1/2 PHILLIPS QTY 50 W/ BIT
OR‐CFHWTRX ‐ KIT SCREW #4‐1/2 TORX ZINC QTY 100 WITH BIT
OR‐CFSP348 ‐ H PROFILE PANEL SPLICE, 48"
OR‐CFB90P ‐ BEAM, CONTAINMENT, PLASTIC 90"
OR‐CFB90A ‐ BEAM, CONTAINMENT, ALUMINUM 90"
OR‐CFSC96 ‐ FLAP SEAL, 96"
OR‐CFBS296 ‐ BULB SEAL, 96"
OR‐CFVTA815CSA
OR‐CFVTA815CSP
OR‐CFVTA815RSA
OR‐CFVTA815RSP
OR‐CFVTA820CSA
OR‐CFVTA820CSP
OR‐CFVTA820RSA
OR‐CFVTA820RSP
OR‐CFVTA830CSA
OR‐CFVTA830CSP
OR‐CFVTA830RSA
OR‐CFVTA830RSP
OR‐CFVTA840CSA
OR‐CFVTA840CSP
OR‐CFVTA840RSA
OR‐CFVTA840RSP
OR‐CFPMW4848 ‐MULTIWALL PANEL 48" X 48"
Aisle Kit Part number
8' Vertical Aisle Kit Component Quantities:
24
24
24
24
28
28
28
28
40
40
40
40
52
52
52
52
12
12
6
6
18
18
9
9
24
24
12
12
36
36
18
18
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
8
8
8
8
10
10
10
10
12
12
12
12
16
16
16
16
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
5
5
5
5
6
6
6
6
9
9
9
9
8
8
0
0
12
12
0
0
16
16
0
0
24
24
0
0
10
10
10
10
14
14
14
14
20
20
20
20
30
30
30
30
3
3
2
2
5
5
4
4
6
6
4
4
8
8
6
6
2
2
2
2
3
3
3
3
4
4
3
3
6
6
5
5
16
16
16
16
20
20
20
20
32
32
32
32
40
40
40
40
0
27
0
21
0
39
0
30
0
51
0
39
0
75
0
57
27
0
21
0
39
0
30
0
51
0
39
0
75
0
57
0
6
6
6
6
8
8
8
8
10
10
10
10
14
14
14
14
6
6
6
6
8
8
8
8
10
10
10
10
14
14
14
14
Vertical Aisle Kit Part Numbers:
OR-CFVTA _
__
_S
_
Beam material: A = aluminum, P= plastic
Support style: R = roof, C= cabinet
Aisle length (feet)
Aisle height(feet)
INSTRUCTION SHEET #:
OR-71601931
REV:
00
ECN #:
SHEET:
34 of 34
DWN BY:
RA
DATE:
02/10/2017
CHK BY:
MDQ
DATE:
03/01/2017
APP. BY:
CV
DATE:
3/22/2017
">