Electrolux T3900 Error codes

Operating manual
T3900/31200
487 25 97 31.00
EN
Tumble dryer
Safety instructions
This machine is only intended for drying water-washed garments.
Clothes that have been cleaned with chemicals/flammable liquids, must NOT
be dried in the machine.
Remove clothes from the tumble dryer as soon as they are dry. This prevents
them from becoming creased, and reduces the risk of spontaneous ignition.
The machine must not be used for drying foam rubber or foam-like materials.
The machine must not be used for drying floor mops*.
The machine must not be used by minors.
The machine must not be hosed down with water.
Adequate ventilation has to be provided to avoid the back flow of gases into
the room from appliances burning other fuels, including open fires.
Mechanical, electrical and gas installations must only be carried out by
authorised personnel.
If the machine has a fault, this must be reported as soon as possible to the
person in charge. This is important for your own safety and for the safety of
others.
Gas dryers only:
The machine is not to be installed in rooms containing cleaning
machines with perchloroethylene, TRICHLOROETHYLENE or
CHLOROFLUOROCONTAINING HYDROCARBONS as cleaning agents.
What to do if you smell gas:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Evacuate the room, building or area.
Contact the laundry manager.
Emergency stop (T3900/T31200)
If the machine for some reason
has to be stopped – press
emergency stop button.
When the necessary measures
have been taken, pull out the
emergency stop button. (The
emergency stop button is an option
outside EU and EEA).
* Applies only to floor mops containing polypropylene.
3
4
Instructions for use
Glossary
Auto Stop
The tumble dryer stops automatically when the clothes are dry.
RMC (Residual Moisture Control)
The tumble dryer has residual moisture control.
Tumble dryer
Contents
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dryer with standard loading door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Dryer with Sliding Door and tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Tilting operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To be carried out by qualified personnel:
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
If the tilting function fails in tilted position . . . . . . . . . . . . . . . . . . . . . . . 18
The manufacturer reserves the right to modify design and material
specifications without notice.
Textiles as silk and wool must not be overdried
to avoid the risk of creasing.
5
6
Instructions for use
Dryer with standard loading door
Heating unit
Emergency
stop
Operating panel
see the following page
Standard
loading door
Drum
Filter door / filter
Instructions for use
Dryer with Sliding Door and tilt
Heating unit
Emergency stop
Operating panel
see the following page
Loading door
Drum
Filter door / filter
Tilt
7
8
Instructions for use
Operating panel - buttons and symbols
P
P button
Reversing
Program selection button.
Not active on pay machines.
Reversing on/off.
OPL laundries only.
With RMC: Push button during
operation, display shows: the
residual moisture in the clothes.
Time button
Cool-down time
Setting of drying time.
Not active on pay machines.
Setting of cool-down time.
OPL laundries only.
Temperature button
Heat
Temperature selection.
When light-emitting diode is lit
the heat is on.
Push button during operation,
display shows: the outlet
temperature.
Selected temperature
Filter
Light-emitting diode is lit at
selected temperature.
When light-emitting diode is lit
filter door/ filter drawer is open.
Start/stop button
Gas reset button
Start: Push button.
Gas dryer only and with
standard loading door.
Stop: Push button or open
door.
Program status
“d xx” = Time controlled drying - xx indicates the time.
“c xx” = Time controlled cool-down - xx indicates the time.
“c - -” = Temperature controlled cool-down.
“ 00” = Standby. The dryer runs an anti-crease program for 120 minutes or until the
door is opened.
9
Instructions for use
Operating panel - buttons and symbols
Options- Sliding Door and tilt
Knob for adjusting the rotation
speed of the drum
Indicator lamp for finished
drying cycle
Tilt
ROTATION
Drum rotation while emptying
the dryer
TILT
Tiltning the dryer.
The tilting can be disconnected
by turning the knob back to
upright position.
ROTATION
Rotation of drum in both
directions during the emptying
process.
10
Instructions for use
Programs OPL
Programs P 01 - P 09 on dryers with RMC
Program
Process
Textiles
P 01
Extra dry
Denim
P 02
Ready to put away
100% cotton / poly cotton mixture / terry
P 03
Ironing dry (5% moisture)
Polyester / nylon
P 04
Ironing dry (10% moisture) Wool / silk
P 05
Ironing dry (15% moisture) Viscose / acetate
P 06
Ironing dry (20% moisture) Mixed textiles
P 07
10 min drying
All textiles
P 08
20 min drying
All textiles
P 09
30 min drying
All textiles
Programs P 01 - P 05 on dryers with Auto Stop
Program
Process
Textiles
P 01
Extra dry
Denim
P 02
Ready to put away
100% cotton / poly cotton mixture / terry
P 03
10 min drying
All textiles
P 04
20 min drying
All textiles
P 05
30 min drying
All textiles
Temperature
High
Non-iron/normal wash
Cotton and mixed fabrics
Medium
Non-iron/normal wash
Cotton and mixed fabrics
Low
Fine wash/mild wash
Delicate fabrics
No heat
Airing bedspreads, duvets and bedclothes
Load
Full loads are recommended in order to achieve the best result.
Full load is indicated in kilos of dry textile.
Dryer type T3900 = 45 kg
Dryer type T31200 = 60 kg
Instructions for use
11
Tumble dryer with manual operation - OPL
1
2
Clean filter
Close the door
Select programme
or
set the drying time
3
Select
temperature
4
Press start
5
6
Fill garments
into the drum
High
Medium
Low
No heat
P
P 01 Extra dry
P 02 Ready to put away
P 03 Ironing dry (5% moisture)
P 04 Ironing dry (10% moisture)
P 05 Ironing dry (15% moisture)
P 06 Ironing dry (20% moisture)
P 07 10 min. drying
P 08 20 min. drying
P 09 30 min. drying
Cool-down period:
Can be changed.
Reversing
on / off:
Press the clock
button and the button
for cooling down time
at the same time
The tumble dryer stops
Automatically when the clothes are
dry
or
when the selected time has expired.
Wait for the dryer to
stop or press stop.
Restart
To prevent
creasing:
If the tumble dryer is not emptied
immediately after the drying time has
ended, an anti-crease programme is
automatically engaged.
This means that the drum rotates at
short intervals, thereby almost
completely avoiding creasing.
Empty the tumble
dryer as soon as the
program has ended.
Close the door and press
start.
12
Instructions for use
Tilting operation
After ended drying
process
Open the door
Start tilting
Turn the knob all the
way to right position.
TILT
The dryer starts
tilting forward.
Rotation
Use both hands to push and turn the
rotation knobs.
ROTATION
ROTATION
Note: When the drum is rotating
during the emptying process only
one person must operate the dryer.
Remove the clothes.
After ended
emptying process
Turn the tilting knob
all the way back to
the left position.
The dryer is righted.
TILT
With the knob in
upright position it is
possible to rotate
the drum with or
without the Sliding
Door being open.
TILT
Instructions for use
13
Error codes
The dryer has automatic error indication.
Error indication is displayed as a flashing code.
Please refer to the Programming manual for Selecta Control for an explanation of error
codes.
The inspector of the laundry must be contacted should an error be displayed.
The user can, however, try to correct some error codes himself.
Error code E05 or E06
When error code E05 or E06 is displayed this can be due to the motor being too hot.
Stop the dryer and wait for 5 minutes. Start again and choose a program. If this does not
help and the error code reappears a service technician must be contacted.
Error code E11 / E12
When the error code is displayed this can be due to the user having overfilled the dryer.
Remove some of the clothes, close the door, and press the start button. If this does not
help and the error code reappears a service technician must be contacted.
Error code E14. OPL laundries only
When resetting gas error E14 the dryer must be in operation on a program with heat,
and the heating indicator must be on.
The dryer must only be reset 3 times.
If the dryer, however, has to be reset more than 3 times it must be put out of order and a
service technician must be called.
Error code E15
When the error code is displayed this can be due to the user having overfilled the dryer.
Remove some of the clothes, close the door, and press the start button. If this does not
help and the error code reappears a service technician must be contacted.
Error code E16
The error code is displayed if the user presses the start button while the vacuum switch is
already closed.
Resetting by opening / closing the door and pressing start button.
14
Instructions for use
Maintenance
1
The following should be carried out at regular
intervals, depending on the operating frequency.
Daily
• Check that the drum stops when the loading
door is opened.
• Check that the drum stops when the filter door
is opened.
If the dryer operates with the loading door or
filter door open, the machine must be placed
out of order until repairs are made.
NOTE! Contact qualified service personnel to
disconnect power from the affected dryer.
• Check that the dryer does not start until the
start/stop button is activated.
A
2
• Check whether the door packing has been
cleaned (use a moist cloth).
B
• Cleaning of filter compartment:
Remove the door by opening it and detaching
the wire fastened to the finger protector and
pulling the door upwards, fig. 1.
It is unnecessary to remove the lint filter for
cleaning. The air system of the dryer ensures
that lint and dust settle automatically at the
bottom of the filter compartment remove by
using a broom or a vacuum cleaner.
• Check that the lint filter is unbroken.
• Vacuum filter door switch A.
Sliding Door:
• Check that felt gasket B is intact and in good
condition, fig. 2.
• Check the distance between steel frame and
felt, maximum 2,0 mm, fig. 3.
3
B
• Check that the 2 doors are closing tightly and
that the rubber gaskets are intact.
If defective gaskets must be replaced or if the
doors need to be adjusted, a service technician
must be called.
Max. 2 mm
Instructions for use
Maintenance
Quarterly
Check that the following are not clogged by lint
and dust or otherwise blocked:
• Fresh-air intake on the back of the dryer
• The area surrounding the dryer
• Exhaust duct
• Nonreturn flap, if any
• Fresh-air intake to the room
Check that the exhaust system connections are
tight.
• Dryer with RMC
Wipe off/clean drum and lifters with citric acid
(Acidum citricum). If soap/softener residue remains,
it is recommended also to use a coarse sponge.
Lack of cleaning the lifters can reduce the automatic
residual moisture control in the clothes resulting in
the clothes being moister than requested when the
program has ended.
15
16
Instructions for use
Maintenance
Dryer with Sliding Door
Biannually
1. Open Sliding Door completely.
2. Fig. 1. Open both panels.
3. Vacuum thoroughly.
4. Close panels.
1
17
Instructions for use
To be carried out by
qualified personnel
Maintenance
Disconnect the power to the dryer.
Monthly, steam heated dryer:
Cleaning the filter in front of steam calorifier.
1. Open the front panel.
2. Remove the filter as shown.
3. Clean the filter with water or with
compressed air.
D
B
4. Replace the filter and close front panel.
All heating alternatives:
Quarterly
• Check and clean the blower wheel A.
Annually
• At least once a year, the inside wearing
parts should be checked and cleaned for
lint.
• Clean the dryer for lint.
It is important to clean around the drum.
The cleaning can be carried out through
the 4 service holes, B + C.
• Check the component unit D for dust and
carefully vacuum if necessary.
• Check and tighten the support rollers.
Service can be carried out through the 2
service holes C.
Lubrication
All bearings are maintenance free as they
are permanently lubricated.
C
A
18
Instructions for use
To be carried out by
qualified personnel
Min. 1 T
Dryer with tilting function
If the tilting function fails in tilted position
Min. 1 T
If the actuator fails while the dryer is in tilted
position and the dryer is still to be used until the
repairs have been carried out, it is necessary to
get the dryer back in upright position.
Examples of lifting tackle
Min. 1 T
To carry out the following steps it is necessary
to have one of the illustrated pieces of lifting
tackle at one’s disposal. Common to all lifting
tackle is that the lifting capacity must be min. 1
ton.
Righting the dryer
It is impossible to manually tilt the dryer back in
upright position. Carry out the following steps:
The stabilizing of the dryer must be carried
out from the back.
1
1. Fig. 1. Dismount back plate, back skirt and
mounting back piece A.
A
2. Fig. 1. Temporarily dismount the connecting
piece B at the outlet pipe.
A
Note Do not remove the front guiding console,
see fig. 2.
B
A
2
19
Instructions for use
Righting the dryer
3
CL
3. Fig. 3. Position the lifting tackle. It is
important to position the lifting tackle below
the back bearer C so the centre of the lifting
tackle supports the bearer.
C
Before starting to lift the dryer ensure that the
support under the lifting tackle is stable.
4. Fig. 4. Start lifting the dryer a little bit so the
bolt D is released in the slot.
5. Remove bolts in both actuators.
6. Turn the actuators loose of the fittings.
7. Carefully lower the dryer in upright possition.
8. Remove the lifting tackle.
9. Mount the connecting piece at the outlet
pipe.
4
10. Mount the back plates which were
dismounted back in step 1.
11. Connect the outlet pipe to the system.
D
Skrotning av maskin
När maskinen inte längre skall användas måste den lämnas till en återvinningsstation för destruktion. Många detaljer i maskinen går
att återanvända, men den innehåller även annat material som måste tas om hand på ett korrekt sätt. Lämna därför aldrig maskinen
eller delar av maskinen i hushållsavfallet, eftersom det kan leda till hälsorisker eller skador på miljön.
Scrapping of machine
When the machine is no longer to be used, it must be submitted to a recycling facility for destruction. The majority of the components
in the machine can be reused, but it also contains other material that must be taken care of in the correct way. Therefore, never mix
the machine or its parts with domestic waste as this may lead to health hazards or damage to the environment.
Entsorgung des Geräts
Wenn das Gerät nicht länger im Gebrauch ist, muss dieses einer Recyclingstation zur Entsorgung zugeführt werden. Viele
Komponenten des Geräts sind recyclingfähig, enthalten aber auch Materialien, die vorschriftsmäßig entsorgt werden müssen.
Entsorgen Sie daher das Gerät oder Geräteteile niemals im Hausmüll, da dies Gefahren für die Gesundheit oder Umweltschäden nach
sich ziehen kann.
Mise au rebut de machine
Lorsque la machine n’est plus utilisée, elle doit être déposée à une installation de recyclage pour y être détruite. La majorité des
composants de la machine peuvent être réutilisés mais celle-ci contient également d’autres matériaux qui doivent être traités
correctement. C’est pourquoi vous ne devez jamais mélanger la machine ou ses pièces avec les ordures ménagères, risque de
polution pour l’environnement ou la santé.
Desguace de la máquina
Cuando la máquina no tenga que utilizarse más, ha de entregarse a una instalación de destrucción para su reciclado. La mayor
parte de sus componentes pueden volver a utilizarse, pero consta también de otros materiales que han de ser tratados de la manera
correcta. Por esa razón nunca mezclar la máquina ni sus partes con la basura doméstica pues esto podría constituir un peligro para la
salud o dañar el medio ambiente.
Bortskaffelse af maskinen
Når maskinen ikke længere er i brug, skal den afleveres til destruktion på en genbrugsstation. Mange dele i maskinen kan
genanvendes, men den indeholder også andre materialer, der skal håndteres korrekt. Smid derfor ikke maskinen eller dele af den ud
sammen med husholdningens almindelige affald, da det kan være forbundet med sundhedsrisiko eller give miljøskader.
Koneen hävittäminen
Kun konetta ei enää käytetä, se pitää luovuttaa kierrätyskeskukseen tuhottavaksi. Suurinta osaa koneen osista voidaan käyttää
uudelleen, mutta se sisältää myös materiaaleja, jotka pitää käsitellä asianmukaisesti. Älä sen vuoksi koskaan laita konetta tai sen osia
kotitalousjätteen sekaan, sillä se saattaa aiheuttaa terveysriskejä tai vahinkoa ympäristölle.
Skroting av maskin
Når maskinen ikke lenger skal brukes, må den leveres til en gjenvinningsstasjon for destruksjon. Det går an å gjenbruke mange deler
av maskinen, men den inneholder også annet materiale som man må ta hånd om på riktig måte. Legg derfor aldri maskinen eller deler
av maskinen i husholdningsavfallet, siden det kan føre til helse- eller miljøskader.
Afdanken van de machine
Als de machine niet langer gebruikt gaat worden, moet deze ter vernietiging worden aangeboden bij een recyclinginrichting. De
meeste componenten van de machine kunnen worden hergebruikt, maar hij bevat ook ander materiaal dat op een juiste wijze moet
worden behandeld. Daarom de machine of zijn onderdelen nooit bij het huisvuil zetten, want dat kan leiden tot gezondheidsrisico’s of
schade aan het milieu.
Rottamazione della macchina
Quando la macchina non può più essere utilizzata, deve essere affidata a un centro di riciclaggio che ne effettui la rottamazione.
La maggior parte dei componenti della macchina sono riciclabili, ma ce ne sono anche alcuni che devono essere smaltiti in modo
appropriato. Perciò, non mischiare mai la macchina o parti di essa con i normali rifiuti domestici, poiché ciò potrebbe comportare rischi
per la salute o per l’ambiente.
Złomowanie maszyny
Wycofaną z użytkowania maszynę należy przekazać do zakładu utylizacji w celu złomowania. Większość podzespołów maszyny
nadaje się do powtórnego wykorzystania, lecz zawiera ona także inne materiały, z którymi należy postępować w odpowiedni sposób.
Z tego powodu niedozwolone jest łączenie maszyny lub jej części z odpadami domowymi, gdyż może to prowadzić do zagrożenia
zdrowia lub szkody dla środowiska.
Vyřazení přístroje
Přístroj, který již nebude používán, by měl být odevzdán k likvidaci do ekodvora. Většina součástek přístroje může být opětovně
použita, některé ale vyžadují likvidaci přesně daným způsobem. A proto nikdy nemíchejte dohromady přístoje nebo jejich části s
domácím odpadem, mohlo by to vést ke zdravotním rizikům nebo k poškození životního prostředí.
Art. No. 438 9041-90 / 05.35
487 01 05 30.09
TUMBLE DRYERS
HYDRO-EXTRACTORS
Types:
H1... , H1...R , N1...E. , N1...EC. , N1...G1.
N2...E. , N2...G1. , N2...S. , N3....E. , N3....G1. , N3....G3. , N3....LE.
N4...E. , N4...G2. , N4...HW. , N4...S.
N4....E. , N4....G2. , N4....S.
Product standard: EN 60335
Försäkran om överensstämmelse
Vi,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Sverige
EG-Conformiteitsverklaring
Wij,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Zweden
försäkrar under eget ansvar att denna produkt, med typbeteckning och enl. ovan,
är tillverkad i överensstämmelse med följande direktiv:
verklaren hierbij op eigen verantwoordelijkheid dat het produkt van het type en met
het serienummer zoals hieronder vermeld, is vervaardigd conform de volgende
normen:
•
LVD direktive (73/23/EC)
•
EMC direktive (89/336/EC)
•
MD direktive (98/37/EC)
•
Gas direktive (90/396/EC)
•
RoHSdirektive (2002/95/EC)
•
•
•
•
•
LVD - direktivet
EMC - direktivet
MD - direktivet
Gas - direktivet
RoHS- direktivet
(73/23/EC)
(89/336/EC)
(98/37/EC)
(90/396/EC)
(2002/95/EC)
CE Declaration of confirmity
We,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljundby, Sweden
Dichiarazione CE di conformità
Noi,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Svezia
declare under our sole responsibility that the product of the type stated above is
manufactured in conformity with the following [EU] directives:
•
LVD directive (73/23/EC)
•
EMC directive (89/336/EC)
•
MD directive (98/37/EC)
•
Gas directive (90/396/EC)
•
RoHSdirective (2002/95/EC)
dichiariamo sotto la nostra esclusiva responsabilità che il prodotto del tipo specificato
sopra è sopra prodotti in conformità alle seguenti direttive [UE]:
•
LVD direttiva (73/23/CE)
•
EMC direttiva (89/336/CE)
•
MD direttiva (98/37/CE)
•
Gas direttiva (90/396/CE)
•
RoHS direttiva (2002/95/CE)
EG-Konformitätserklärung
Wir, die
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Schweden
Declaração CE de conformidade
Nós,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Suécia
erklären hiermit in alleiniger Verantwortung, daß das Produkt mit der oben
genannten Typen-bezeichnung mit folgenden EU-Richtlinien übereinstimmt:
•
LVD Direktive (73/23/EC)
•
EMC Direktive (89/336/EC)
•
MD Direktive (98/37/EC)
•
Gas Direktive (90/396/EC)
•
RoHSDirektive (2002/95/EC)
declaramos sob nossa inteira responsabilidade que o produto com os números de
série e de tipo abaixo indicados é fabricado em conformidade com as seguintes
directivas [UE]:
•
LVD directiva (73/23/CE)
•
EMC directiva (89/336/CE)
•
MD directiva (98/37/CE)
•
Gás directiva (90/396/CE)
•
RoHS directiva (2002/95/EC)
Déclaration de conformité CE
Nous,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Suède
Δήλωση συμμόρφωσης CE
Εμείς, η εταιρεία
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljundby, Σουηδία
déclarons sous notre seule et unique responsabilité que le produit des type et
numéro de série indiqués ci-dessus est fabriqué conformément aux directives UE
suivantes:
•
LVD Directive (73/23/CE)
•
EMC Directive (89/336/CE)
•
MD Directive (98/37/CE)
•
Gaz Directive (90/396/CE)
•
RoHSDirective (2002/95/EC)
δηλώνουμε με αποκλειστική μας ευθύνη ότι ο τύπος του προϊόντος που αναφέρεται
παραπάνω κατασκευάζεται σύμφωνα με τις ακόλουθες οδηγίες της [ΕΕ]:
Οδηγία περί Χαμηλής Τάσης (73/23/EΕ)
Οδηγία περί Ηλεκτρομαγνητικής Συμβατότητας (89/336/EΕ)
Οδηγία περί Μηχανημάτων (98/37/EΕ)
Οδηγία περί Συσκευών Αερίου (90/396/EΕ)
Οδηγία περί Ηλεκτρικού και Ηλεκτρονικού Εξοπλισμού (2002/95/ΕΕ)
Declaración de conformidad CE
Electrolux Laundry Systems Sweden AB
con sede en SE-341 80 Ljungby, Suecia
CE megfelelıségi nyilatkozat
Mi, az
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Svédország
declara bajo su exclusiva responsabilidad que el producto con el modelo y número
de serie que más adelante se especifica ha sido fabricado conforme a las
siguientes directivas:
•
LVD directiva (73/23/CE)
•
EMC directiva (89/336/CE)
•
MD directiva (98/37/CE)
•
Gas directiva (90/396/CE)
•
RoHS directiva (2002/95/EC)
felelısségünk teljes tudatában kijelentjük, hogy az alább megadott típusú termék
gyártása a következı EU-irányelvekkel összhangban történik:
•
a 73/23/EGK irányelv
•
a 89/336/EGK irányelv
•
a 98/37/EGK irányelv
•
a 90/396/EGK irányelv
•
RoHS direktifi (2002/95/EC)
Erklæring om EU-overensstemmelse
Vi,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Sverige,
EF-samsvarserklæring
Vi,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Sverige
erklærer på eget ansvar, at produktet med typebetegnelse som angivet er
fremstillet i overensstemmelse med følgende EU-direktiver:
•
LVD direktivet (73/23/EC)
•
EMC direktivet (89/336/EC)
•
MD direktivet (98/37/EC)
•
Gas direktivet (90/396/EC)
•
RoHSdirektivet (2002/95/EC)
erklærer på eget ansvar at dette produktet, med typebetegnelse og
produksjonsnummer som angitt nedenfor, er produsert i samsvar med
bestemmelsene i følgende direktiver:
•
LVD direktivet (73/23/EC)
•
EMC direktivet (89/336/EC)
•
MD direktivet (98/37/EC)
•
Gas direktivet (90/396/EC)
•
RoHS direktivet (2002/95/EC)
EY-Vaatimustenmukaisuusvakuutus
Me,
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Ruotsi
CE megfelelıségi nyilatkozat
Mi, az
Electrolux Laundry Systems Sweden AB
SE-341 80 Ljungby, Svédország
vakuutamme yksinomaan omalla vastuullamme, että tuote, jonka tyyppitunnus
lukee yllä, on valmistettu seuraavien [EU]-direktiivien mukaisesti:
•
LVD direktiivi (73/23/EC)
•
EMC direktiivi (89/336/EC)
•
MD direktiivi (98/37/EC)
•
Kaasu direktiivi (90/396/EC
•
RoHSdirektiivi (2002/95/EY)
felelısségünk teljes tudatában kijelentjük, hogy a fent megadott típusú termék gyártása a következı EU-irányelvekkel összhangban történik:
•
LVD a 73/23/EC irányelv
•
EMC a 89/336/EC irányelv
•
MD a 98/37/EC irányelv
•
Gas a 90/396/EC irányelv
•
RoHS direktíva (2002/95/EC)
Ljungby 2006.05.23
Bert Nordholm
Production Director
Electrolux Laundry Systems
Lundtoftegaardsvej 93A, DK-2800 Lyngby, Denmark
Telephone: +45 4526 4800. Telefax: +45 4526 4801
Internet: www.electrolux.com/laundrysystems
E-mail: [email protected]
">