Anker SOLIX Power Dock Pro (Three-Phase)
[email protected]
(UK) +44 (0) 1604 936 200
2 Unboxing
For User Guide / App / Support
1 Overview
• When the Power Dock Pro is installed, Backup Port on the inverter should not be connected.
• When connected to Power Dock Pro, X1 Power Module supports a maximum of two units in parallel. For supported inverter models, refer to the online
Installer Guide.
• For a two-inverter parallel connection to the Power Dock Pro, the communication cable can be connected to either inverter.
Anker SOLIX Power Dock Pro
Decorative Cover
T-shaped Rear Bracket
M4
×1
Primary Scenario
*Dashed boxes indicate
optional components.
Main Panel
AC Cable
Grid
Circuit Breaker Locking Pin
Waterproof Connector
(AC Cable Gland) ×6
M8 70 mm
×4
Flange Nut
Waterproof Connector
(Signal Cable Gland) ×1
20-pin Pluggable
Terminal Block
M4 12 mm
×4
M5 12 mm
×1
M8 70 mm
×4
Expansion Bolt
Self-Tapping Screw
Screw
Network Cable for
X1 Power Module
Thumb Screw
Documents
Communication Cable
Fuse
Main Meter
Sub Panel
3 Installation
Dimensions
3.1 Select Installation Site
Smart
Port
INV-1
INV-2
Backup
155 mm
450 mm
• Only qualified professionals or trained personnel are allowed to
install and maintain the equipment.
• Install the equipment in a cool, sheltered location, away from direct
sunlight and rain.
• Plan cable routing to keep the network cable for X1 Power Module
within 30 m.
Grid
Spacing
≥200 mm
25 mm
≥60
0m
700 mm
≥200 mm
m
≥200 mm
NonBackup
150 mm
≥350 mm
Non-Backup Loads
Non-Backup Loads
Third-party
PV System
3.2 Remove Door and Inner Panel
Backup Loads
3.3 Mount the Bracket
M4
3
PV Panels
PV+
RJ45
RJ45
PV-
AC Grid
PV Panels
PV+
RJ45
RJ45
PV-
AC Grid
≥1000 mm
26 kg
8 mm
1N·m
75-80 mm
90
︒
1
2
Inverter 2
Inverter 1
M4
Other Scenario
1N·m
M5
4
1N·m
M4
1N·m
4 Electrical Connections
Main Panel
Grid
Fuse
M8
8.8 N · m
• Before wiring, ensure the main circuit breaker is off.
• Disconnect and remove wiring of existing Anker SOLIX energy storage systems from the distribution box for reconnection.
Main Meter
Sub Panel
4.1 Wiring Suggestions
Option 1: Bottom Cable Entry
Option 2: Rear Cable Entry
1
1
Grid
CT1
1
1
CT2
INV-1
INV-2
Backup
2
2
2
Backup Loads
2
3
3
7
2
8
7
8
1
1
Routing Hole 1
Non-Backup
Loads
Third-party
PV System
2
Routing Holes 2-7
3
3
6
5
3
PV+
RJ45
RJ45
PV+
PV-
AC Grid
Inverter 1
PV Panels
PV-
1
RJ45
RJ45
1
1
2
3
4
5
6
22
33
44
55
6
5
7 8
L1
L2
L3
2
3
4
5
6 75 8
66 77 8
AC Grid
Inverter 2
4
3
1
PV Panels
4
N
PE / PEN
Communication Cable
1
Communication cable
2
Smart port cable
3
Inverter cable
4
Inverter cable
5
Backup load cable
6
Non-backup load cable
7
Grid cable
8
PEN Cable
4.2 Connect the PEN Cable
4.3 Connect the PE Busbar
4.6.2 Connect RS485 Cable
Connect the PE busbar of the Power Dock Pro to the PE
busbar of the distribution panel.
• The following sections use bottom cable entry as an example. For rear
entry, refer to the online Installer Guide.
• Tighten the circuit breaker terminals to the specified torque: 3.5 N.m for 80 A
breakers and 2 N.m for 63 A and 32 A breakers.
The method to connect the DI / DO / RS485 cable is the same. This section takes connecting the RS485 cable as an example.
1
The PEN conductor must be connected to the building's Main Earthing Terminal (MET).
2
10 mm
PEN
Main Panel
COM 1
Meter_B
PE
12±1 mm
4
Φ 2-4mm
PEN
Meter_A
20
19
2
1
3
M5
0.2-1.5 mm2
3.5 N · m
4.4 Connect to Inverter / Backup Loads / Non-Backup Loads / Power Grid
Anker SOLIX Power Dock Pro
INV-1
≤16 mm2
A
L1
12±1 mm
B
Φ
A
L3
N
B
PE
/
>L+3 mm
M5
M5
2N·m
3.5 N · m
Cable Type
Outer diameter
Cross-sectional area of
core conductor
Inverter Cable
8-17 mm
6 mm2
Grid / Backup Load /
Non-Backup Load Cable
9-25 mm
16 mm2
L2
L
5 Complete Connections
5.1 Install Inner Panel and the Cover
5.2 Install Decorative Cover (Optional)
1
4.5 Connect to Smart Port Loads
2
1
3
≤16 mm2
Smart
Port
L1
12±1 mm
L2
A
Φ 9-25mm
B
L3
N
2
PE
M5
M5
2N·m
3.5 N · m
>L+3 mm
L
M4
1N·m
4.6 Connect Communication Cables
Different communication ports are not interchangeable. Verify the port labels before connecting to avoid system malfunction.
4.6.1 Connect the Network Cable for X1 Power Module
The network cable for X1 Power Module is included in the accessory kit. If you need to make your own cable, follow the steps below.
M4
2N·m
6 Device Setup
1. Switch on the circuit breakers in the following order:
QF5 → QF2 / QF3 → QF1 → QF4.
2. Close and lock the equipment door.
3. Download the Anker SOLIX
Professional app and follow the
in-app instructions and online
Installer Guide to complete the setup.
During normal operation, keep the circuit
breaker locking pin engaged to ensure the
bypass switch remains in the OFF position.
1
1 2 3 4 5 6 7 8
0.13-0.2 mm2
< 30m
M4
1N·m
8
6
4
2
7
5
3
1
Φ 4-7.5mm
M5
1
1N·m
8
or
1 2 3 4 5 6 7 8
2
M5
8
7
2
1
COM 2
Anker SOLIX Power Dock Pro
RJ45
Anker SOLIX X1 Power Module
Model: Power Dock Pro 63-T0-EU
51005006560 V1
">