Mastercool 91000-A DELUXE CLUTCH HUB PULLER/INSTALLER KIT Instructions

Removers
/ AN
Installers
Removers
y a YN
90454 91195
В
|
91212 91260 90458
-
он
0281-054
1052-001 —
|
НШ
X
J
1
В
—
[1
92260
90902
Installer
|
Mastercool!…
Remover/Installer
One Aspen Drive, Randolph, NJ 07869
www.mastercool.com
wr Mastercool...
_— "World Class Quality”
PART# 91000-A
Deluxe A/C Clutch Hub Puller & Installer
REMOVING PROCEDURE:
1. Remove shaft nut or retaining ring.
2. Thread removing tool onto hub. Position center screw
against the end of compressor shaft.
3. Hold body of remover with wrench and turn center screw
into remover body to remove clutch hub assembly.
INSTALLING PROCEDURE:
1. Ensure frictional surface of clutch plate and rotor is clean.
2. Align shaft key with shaft keyway and place clutch plate
and hub assembly on compressor shaft.
(Do not drive or pound on clutch hub or shaft, as this
may cause internal damage to compressor.)
3. Attach installing tool onto compressor shaft.
(Body of installing tool should be backed off
sufficiently to allow center screw to be threaded
fully onto end of compressor shaft).
4. Hold center screw with wrench and tighten hex portion of
installer to press hub onto shaft.
5. Tighten body several turns until the air gap between the
friction surfaces is .020 - .030 inch.
6. Remove installer and check for proper positioning
of shaft key.
7. Install shaft nut or retaining ring.
(Refer to manufacturer specification for correct torque).
8. Spin pulley by hand to check for free operation.
/ WARNING!
e Puller parts can break under stress! e Be aware of hand positions.
* Wear safety goggles (user and bystanders)! * Read and follow instructions.
* Do not heat pullers! e Broken parts can cause injury!
* Do not over stress pullers! » Avoid contact with refrigerant!
Compressor Type Used
Vohicios from (és present) Make Remover Installer
Make Nippon Sanden York Harrison Zexel Seiko Diesel Harrison GM
Tecumseh Hitachi Seiki Kiki DA-6, HR-6 & V5 91212 Nut 8 Arbor 90458 Nut, Bearing &
Acura X i 91260 Arbor nn
American Motors A-6 & Earlier R4 90454 Nut & Arbor 90458 Nut, Bearing &
Audi X I Arbor .... tete te
BMW R4 90454 Nut & 90458 Nut, Bearing &
— 1 1 1 1 4% 1 tt bh. 91195 Arbor ..........| 91260 Arbor nn
Buick Nippondenso
Cadillac Ford / Chrysler
Chevrolet A590, C171 & FS-6 | 91122 Nut & 90458 Nut &
ChevroletTruck | | | Xx |} 1 NI fe À 91212 Arbor | 1052-001 Arbor & Washer
For FS-6 W / Special | 91122 Nut & Arbor 90458 Nut &
2ammx2.0 bee... |. 1052-001 Arbor 8 Washer |
New Style 90454 Nut 8 Arbor 90458 Nut &
eee... | 1052-001 Arbor & Washer |
Fiat Sanden 90902 Puller Plate
Ford ~~ 1 XxX x rr vt 1 TT Verre EEE PEE & Arbor 2200 0 ee 0 0 fe ee ee ee ee ee ee eee ee eee eee 11111200
Ford Truck York / Tecumseh 91122 Nut & 90458 Nut &
SMC Truck HR980 | 91212 Arbor | 1052-001 Arbor & Washer
Zexel / Mitsubishi 92260 Arbor &
Honda CH Series 90902 Puller Plate
Lexus
Lincoln
Mazda
Mercedes Benz
Nippondenso Variable Displacement
A590 C171 Compressor
Mitsubishi
Nissan
Oldsmobile Harrison Harrison Harrison Harrison
Axial (A-6) Radial (R-4) DA-6/HR-6/HE-6 V-5 Compressor
Truck
Pontiac
Porsche
Renault
Saab
Saturn
Subaru
Suzuki
Toyota
Volvo York & Tecumseh Hitachi