Digital Watchdog V3363D922 User manual

5436 W Crenshaw St. Tampa, FL 33634

Tel: 866-446-3595 / 813-888-9555

Fax: 813-888-9262 www.Digital-Watchdog.com

[email protected]

Technical Support Hours: Monday-Friday

8:30am to 8:00pm Eastern Time

V3363D, V3363D922

V3363DH

V3367WD, V3367WTIR

Vandal Dome Camera

User Manual

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for future reference.

01312012

PRECAUTIONS

■

Do not open or modify.

■

Do not open the case except during maintenance and installation,

for it may be dangerous and can cause damages.

■

Do not put objects into the unit.

■

Keep metal objects and flammable substances from entering the camera. It can cause fire, short- circuits, or other damages.

■

Be careful when handling the unit.

■

To prevent damages, do not drop the camera or subject it to shock or vibration.

■

Do not install near electric or magnetic fields.

■

Protect from humidity and dust.

■

Protect from high temperature.

■

Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.

■

Cleaning

■

■

To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.

Mounting Surface

■

The material of the mounting surface must be strong enough to support the camera.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful interference .when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.

WARNING : Changes or modifications are not expressly approved by the manufacturer.

2

TROUBSHOOTING

Before sending your camera for repair, check the following or contact our technical specialist.

No VIDEO

Check the coaxial cable and make sure it is connected securely.

Check the lens’ iris adjustment at the menu setup of the camera.

Check the power supply and make sure the camera has the proper voltage and current.

Out-of-Focus VIDEO

Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.

Check the lens manual focal and zoom adjustment. Field test monitor is recommended.

3

4

F

EATURES*

- V3363D

■

1/3" High Resolution CCD

■

High Resolution 560 TV Lines

■

3.3 ~ 12mm Varifocal Auto Iris Lens

■

Electronic Day and Night

■

Star-Light (Super Low Light Technology)

■

DRC (Dynamic Range Compressor)

Dark spots in images particularly become more visible without overexposing the bright

spots to create one perfect image.

■

3D-DNR (3D Digital Noise Reduction)

Produces less noise and more color during low-light application.

■

HME (Highlight Mask Exposure)

Masks overly exposed light to produce a true video image of any environment.

■

BLC (Back Light Compensation)

■

Programmable Privacy Zone (8) & Motion Detection

■

Easy Icon Driven OSD Menu with Built-In Joystick

■

Auto Sensing 12VDC or 24VAC with Line Lock

■

No Fog or Condensation under Any Weather Condition

F

EATURES*

- V3363D922

■


■


■

9~22mm Varifocal Auto Iris Lens

■


■


■




■



■



■


■


■


■


■


5

6

F

EATURES*

- V3363DH

■


■


■

3.3~12mm Varifocal Auto Iris Lens

■


■


■




■



■



■


■


■


■


■

Built-in Heater , Withstand Temperatures as Low as -40°F

■


F

EATURES*

- V3367WD

■

1/3” Sony Super HAD II CCD

■


■


■


■


■




■



■



■

SLC (Side Light Compensation)

■

DIS (Digital Image Stabilizer)

■


■


■


■


7

8

F

EATURES*

- V3367WTIR

■

1/3” Sony Super HAD II CCD

■


■


■

100ft Range IR with Intelligent Camera Sync

■

True Day & Night / TDN5 (Electro Magnetic Mechanism)

■


■

Max-DR (Electronic Wide Dynamic Range)

Enables the camera to capture perfect images in both bright and dark environments

simultaneously.

■



■



■


■


■


■


■


■


D

IMENSIONS IN MILLIMETERS*

102.0

61.8

91.0

85.0

R2.5

47.8

32.8

85.0

91.0

ø140.1

1. ROTATE ZOOM LEVER TO DISPLAy DESIRED VIEW.

2. ROTATE FOCUS LEVER TO ADJUST THE FOCUS.

VIDEO(yellow)

BNC JACK

DC12V or AC24V

RED

5mm TWIST SOLD DERING

BLACK

L=300mm

9

I

NSTALLATION*

3 4 5

1

2

6

7

1. Mounting Template

2. User Manual

3. Security L-Key

4. Single Sided Hex Key

5. Double Sided Hex Key

6. Secondary BNC Cable for Field

Monitor

7. Four (4) Screws and Four (4) Dry

Wall Anchors

8. 3 Axis Gimbal Guide

8

Camera Installation

Use the mounting template to mount the camera.

Using the security L-key to loosen the four screws that secure the vandal proof dome cover,

Remove the vandal proof dome cover to access the screw holes to mount the camera.

NOTE: Keep the lens and the vandal proof cover free from dust or fingerprint.

10

I

NSTALLATION*

A. Use the supplied L Wrench to remove the four fixing screws from the dome cover.

B. Align the camera unit with the surface of the ceiling.

Draw marks on the ceiling in the places where the screw holes will be drilled. Drill the four holes.

C. Cut a small hole in the ceiling for the cables.

D. Pass the power cable and video cable from the camera unit through the cable hole in the ceiling.

E. Align the four screw holes in the camera unit with the screw holes on the ceiling, and then secure the camera in place by tightening the four screws through the

washers.

F. Carry out the settings and adjustments for the camera.

G. Secure the dome cover by tightening the screws.

B

D

E

A

F

C

G

11

C

ONNECTION*

12VDC/24VAC VIDEO OUT

300.0

CAUTION : CHECk FOR POLARITy WHEN USING A DC12V POWER SUPPLy.

12

C

MAERA SETTINGS*

■

LENS ADJUSTMENT a. Focus lever b. Zoom Lever

1. Set the zoom level as desired positiong by moving Zoom lever.

2. Set the Focus level as the image is focussed by moving Focus lever.

13

C

AMERA SETTING FOR SIDE OSD CONTROL BOARD*

2nd Video

Joystick key

The functions of joystick are camera zoom in/out and OSD control.

2nd Video

Video Test output connector.

JoyStick Key

CAUTION : CHECk FOR POLARITy WHEN USING A DC12V POWER SUPPLy.

14

M

ODULE OSD MENU*

-V3363D, V3363D922, V3363DH

COLOR EXPOSURE

BRIGHTNESS

AE PREFERENCE

BLC / HME

AGC

STARLIGHT

NIGHT-UP

WB MODE

R-y GAIN

B-y GAIN

DAy&NIGHT

D&N MODE

C_SUP

A_SUP

MOTION

MOTION

PRIVACy

PRIVACy

FUNCTION

MIRROR

SHARPNESS

FREEZE

D-ZOOM

3D DNR

DRC

SyNC

SyNC

SETUP

TITLE EDIT

PC CONTROL

(RS485 Control)

LANGUAGE

MONITOR

OSD COLOR

OMNI LENS

DEFECT

EXIT

EXIT

SAVE & EXIT

FACTORy SET

15

O

SD MENU*

-V3363D, V3363D922, V3363DH

EXPOSURE

BRIGHTNESS

SHUTTER

BLC/HME

AGC

STARLIGHT

NIGHT-UP

EXIT JUMP

COLOR

WB MODE

R-y GAIN

B-y GAIN

EXIT

DAy & NIGHT

Day & Night Mode

C-SUP

A-SUP

EXIT

0 ~ 100

1/60 / FLK / 1/250 ~ 10000 / STARLIGHT x2 ~ x256

OFF / BLC / HME

HIGH / MIDDLE / LOW / OFF

AGC(Auto Gain Control)

AUTO(x2 ~ x256) / OFF

NORMAL / HIGH

EXIT / SAVE&EXIT / FACTORy SET

AWC / AWT / PUSH LOCK / MANUAL / INDOOR / OUTDOOR

0 ~ 100

0 ~ 100

JUMP

AUTO : READ TIME(0~63) / S-LEVEL / E-LEVEL

COLOR---->BW : B&W : Switching from COLOR to BW; If the number is higher, the camera will only switch during a super low light condition

BW ---->COLOR : Switching from BW to COLOR; This number should be always lower than

COLOR to BW

Read Time : time interval to switch from COLOR to BW

COLOR

B&W Mode : BURST (OFF / ON) There is less noise when the BURST is OFF.

SMART IR (OFF / ON)

Color Suppression : Color will be reduced at low illumination, if the C-SUP Level is set higher. 0 ~ 63

Aperture Suppression : The sharpness of the edges will be reduced at low illumination, if

A-SUP level is set higher. 0 ~ 15

JUMP

16

FUNCTION

MIRROR

SHARPNESS

FREEZE

NEG.IMAGE

D-ZOOM

3D-DNR

DRC

OFF/MIRROR/V-FLIP/ROTATE

0 ~ 31

OFF / ON

OFF / ON

OFF / ON (x1.0 ~ x32 PTZ)

ON (0~100) / OFF

3D Digital Noise Reduction

OFF / INDOOR / OUTDOOR

Dynamic Range Compressor

EXIT JUMP

MOTION (OMNI-Plus Camera Only)

OFF

MOTION

EXIT

PRIVACy

ON

AREA SELECT (AREA 1~4)

AREA SET (POSITION / SIZE)

SENSITIVITy (0~40)

MOTION TRACE (OFF / ON)

MOTION VIEW (OFF / ON)

RETURN

JUMP

PRIVACy

EXIT

OFF

ON

AREA SELECT (1~8)

AREA SET (POSITION / SIZE)

COLOR (0~15)

RETURN

JUMP

17

18

SyNC

SyNC

EXIT

SETUP

TITLE EDIT

PC CONTROL

(RS485 Control)

LANGUAGE

MONITOR

OSD COLOR

OMNI LENS

DEFECT

EXIT

EXIT

EXIT

SAVE&EXIT

FACTORy SET

INTERNAL / AUTO

JUMP

OFF / ON

CAM ID / ID DISPLAy (OFF/ON) / BAUDRATE (2400/4800/9600/19200/38400/57600)

The protocol is fixed pelco-D.

ENG / KOR / JPN / CHN1 / CHN2 / RUS / FRAN / SPAN / ITAL

CRT / LCD / USER

Select LCD only if the camera is directly connected to the LCD monitor.

0 ~ 15

OFF (OMNI-Plus Camera Only)

ON

ALARM / READ TIME / ALARM ZOOM / STAND By / RETURN

WHITE DEFECT CANCEL MODE

JUMP

M

ODULE OSD MENU*

-V3367WD, V3367WTIR

COLOR EXPOSURE

BRIGHTNESS

E.SHUTTER

BLC

MAX_DR

AGC

STARGLIGHT

WB MODE

R-y GAIN

B-y GAIN

DAy&NIGHT

D&N MODE

C_SUP

A_SUP

FUNCTION

MIRROR

SHARPNESS

GAMMA

FREEZE

NEGA.

3D DNR

D-ZOOM

SLC

HME

DIS

SyNC

SyNC MODE

MOTION

MOTION

SETUP

CAMERA ID

TITLE

DPC

MONITOR

LANGUAGE

BAUDRATE

OMNI LENS

PRIVACy

MASK 1

MASK 2

MASK 3

MASK 4

MASK 5

MASK 6

EXIT

EXIT

SAVE & EXIT

FACTORy RESET

19

O

SD MENU*

-V3367WD, V3367WTIR

EXPOSURE

BRIGHTNESS

E.SHUTTER

BLC

AGC

MAX_DR

STARLIGHT

EXIT JUMP

COLOR

WB MODE

R-y GAIN

B-y GAIN

EXIT JUMP

DAy & NIGHT

D & N Mode

C-SUP

A-SUP

EXIT JUMP

0 ~ 99

1/60, 1/100FLC, 1/120~1/100000

OFF / ON



AGC(Auto Gain Control)

OFF / ON (0~20) (Electronic Wide Dynamic Range)

AUTO (x2 ~ x256) / OFF (x32 is recommended for low light application.)

EXIT / SAVE & EXIT / FACTORy SET

AWC / ATW / MANUAL / PUSHLOCK

0 ~ 255

0 ~ 255


AUTO / COLOR / BW

COLOR---->BW : Switching from COLOR to BW; If the number is higher, the camera will only switch during a super low light condition.

BW ---->COLOR : Switching from BW to COLOR; This number should be always lower than

COLOR to BW

Read Time : time interval to switch from COLOR to BW

COLOR

B&W Mode : (BURST : OFF/ON) When the burst is OFF, the picture will have less noise.

Color Suppression : Color will be reduced at low illumination, if the C_SUP Level is higher.

0 ~ 100 (not available when 3D-DNR is on)

Aperture Suppression : Edge sharpness will be reduced at low illumination, if A_SUP Level is higher. 0 ~ 100 (not available when 3D-DNR is on)


20

FUNCTION

MIRROR

SHARPNESS

GAMMA

FREEZE

NEGA.

3D-DNR

D-ZOOM

SLC

HME

DIS

EXIT JUMP

MOTION

MOTION

EXIT JUMP

OFF/MIRROR/V-FLIP/ROTATE

0 ~ 49

0.45 ~ 1.00 / USER

OFF / ON

OFF/ ON

OFF / LOW / MIDDLE / HIGH

3D DNR (3D Digital Noise Reduction)

OFF / ON(x1.0 ~ x3.0 Digital PTZ)

OFF / ON


OFF / ON

HME (Highlight Masking Exposure)

OFF /ON



OFF / ON

SET WINDOW

ALL SET (Set the Entire Screen)

ALL CLEAR (Clear the Entire Screen)

SENSITI.(1~120)

SHOW INDI.(OFF / ICON / TRACE)

DELAy OUT (1 ~ 15)

Motion Alarm Zoom-In Delay


21

PRIVACy

MASK 1

MASK 2

MASK 3

MASK 4

MASK 5

MASK 6

EXIT JUMP

SyNC

SyNC MODE

V-PHASE

EXIT JUMP

SETUP

CAMERA ID

TITLE

DPC

MONITOR

LANGUAGE

BAUDRATE

OMNI LENS

EXIT JUMP

EXIT

EXIT

SAVE&EXIT

FACTORy SET

OFF / ON

OFF / ON

OFF / ON

OFF / ON

OFF / ON

OFF / ON


INTER / AUTO

0 ~ 199


0 ~ 254 (RS485 ID)

OFF / ON

OFF / AUTO

DPC (Dead Pixels Cancellation)

CRT / LCD (Select LCD only if the camera is directly connected to LCD monitor.)

English / Chinese

2400 / 4800 / 9600 / 14400 / 19200 / 38400

The protocol is Pelco-D. Fixed and cannot be changed.(Hardcoded onto the DSP.)

OFF / 0


Exit the menu

Exit the menu and save the setting

Reset the menu setting to factory default

22

W

ARRANTy INFORMATION*

Digital Watchdog (referred to as “the Warrantor”) warrants the Camera Series against defects in materials or workmanship as follows.

LABOR : For the initial two (2) years from the date of original purchase, if the camera is determined to be defective, the Warrantor will repair or replace the unit, with new or refurbished product at its option, at no charge.

PARTS : In addition, the Warrantor will supply replacement parts for the initial two (2) years.

To obtain warranty or out of warranty service, please contact a Technical Support Representative at

1-866-446-3595 Monday through Friday from 8:30AM to 8:00PM Eastern.

A purchase receipt or other proof of the original purchase date is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use.

This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.

23

L

IMITS AND EXCLUSIONS*

There are no express warranties except as listed above.

The Warrantor will not be liable for incidental or consequential damages (including, without limitation, damage to recording media) resulting from the use of these products, or arising out of any breach

of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

If the problem is not handled to your satisfaction, then write to the Address listed on the next page.

Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in its sole discretion, are not covered. Costs of such service calls are the responsibility of the purchaser.

24

S

PECIFICATIONS*

-V3363D

Camera TYPE

Image

Scanning

Min. Scene Illumination

Functions

Lens

Resolution

Video Output

S/N Ratio

OSD

Environmental Conditions

Power

Physical Specification

Color/BW

Mount

Size

Pixels-Total

Pixels-Effective

System

Horizontal Frequency Internal Mode

Vertical Frequency Internal Mode

F1.2

x256 Star-Light

BLC

AGC

DRC

Mirror

STAR-LIGHT

3D-DNR

HME

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD

Operating Temperature

Humidity

Power Requirement

Power Consumption

Dimensions

Weight

Nema Type

Certifications

V3363D

Surface

1/3"

811(H) X 508(V)

768(H) X 494(V)

525 line, 2:1 Interlace

15,734Hz

59.94Hz

0.14 Lux

0.0005 Lux in Color

ON / OFF



OFF / MIRROR / V-FLIP / ROTATE

AUTO (x2~x256) / OFF

OFF / ON (0~100)

OFF / ON

8 Programmable Zone / Size


560 TV Lines [Color]; 580 TV Lines [BW]

VBS 1.0Vp-p(75 Load)

52dB yES

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90%

12VDC / 24VAC

1.96 [W] / 2.2 [W]

109.6 X 140.1mm

1.9lbs

IP66

FCC, RoHS, CE

25

S

PECIFICATIONS*

-V3363D922

Camera TYPE

Image

Scanning


Functions

Lens

Resolution

Video Output

S/N Ratio

OSD


Power

Physical Specification

Color/BW

Mount

Size

Pixels-Total

Pixels-Effective

System



F1.2

x256 Star-Light

BLC

AGC

DRC

Mirror

STAR-LIGHT

3D-DNR

HME

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD


Humidity

Power Requirement

Power Consumption

Dimensions

Weight

Nema Type

Certifications

V3363D922

Surface

1/3"

811(H) X 508(V)

768(H) X 494(V)


15,734Hz

59.94Hz

0.14 Lux

0.0005 Lux in Color

ON / OFF





OFF / ON (0~100)

OFF / ON


9 ~ 22mm Varifocal Auto Iris Lens



52dB yES

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90%

12VDC / 24VAC

1.96 [W] / 2.2 [W]

109.6 X 140.1mm

1.9lbs

IP66

FCC, RoHS, CE

26

S

PECIFICATIONS*

-V3363DH

Camera TYPE

Image

Scanning


Functions

Lens

Resolution

Video Output

S/N Ratio

OSD


Power

Color/BW

Mount

Size

Pixels-Total

Pixels-Effective

System



F1.2

x256 Star-Light

BLC

AGC

DRC

Mirror

STAR-LIGHT

3D-DNR

HME

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD


Humidity

Power Requirement

Power Consumption

Physical Specification Dimensions

Weight

Nema Type

Certifications

V3363DH

Surface

1/3"

811(H) X 508(V)

768(H) X 494(V)


15,734Hz

59.94Hz

0.14 Lux

0.0005 Lux in Color

ON / OFF





OFF / ON (0~100)

OFF / ON





52dB yES

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90%

12VDC / 24VAC

1.8 [W] / 2.4 [W] (Heater Off)

13.6 [W] / 14.7 [W] (Heater Off)

109.6 X 140.1mm

1.6lbs

IP66

FCC, RoHS, CE

27

S

PECIFICATIONS*

-V3367WD

Camera TYPE

Image

Scanning


Functions

Lens

Resolution

Video Output

S/N Ratio

OSD


Power

Color/BW

Mount

Device

Size

Pixels-Total

Pixels-Effective

System



F1.2

x256 Star-Light

BLC

AGC

MAX-DR

Mirror

STAR-LIGHT

3D-DNR

SLC

HME

DIS

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD


Humidity

Power Requirement

Power Consumption

28

V3367WD

Surface

Super HADⅡCCD

1/3"

811(H) X 508(V)

768(H) X 494(V)


15,734Hz

59.94Hz

0.14 Lux

0.0005 Lux in Color

ON / OFF


OFF / ON



OFF / ON

OFF / ON

OFF / ON

OFF / ON





50dB yES

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90%

12VDC / 24VAC

1.8 [W] / 2.4 [W]

S

PECIFICATIONS*

-V3367WTIR

Camera TYPE

Image

Scanning


Functions

Lens

Resolution

Video Output

S/N Ratio

OSD


Power

Color/BW

Mount

Device

Size

Pixels-Total

Pixels-Effective

System



IR LED ON

IR Distance

BLC

AGC

MAX-DR

Mirror

STAR-LIGHT

3D-DNR

SLC

HME

DIS

Privacy Zone

Focal Length

Horizontal

VBS 1.0Vp-p

S/N Ratio

OSD


Humidity

Power Requirement

Power Consumption

V3367WTIR

Surface

Super HADⅡCCD

1/3"

811(H) X 508(V)

768(H) X 494(V)


15,734Hz

59.94Hz

0.0 Lux

100ft Range

ON / OFF


OFF / ON



OFF / ON

OFF / ON

OFF / ON

OFF / ON





50dB yES

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90%

12VDC / 24VAC

1.8 [W] / 2.4 [W] LED Off, 4.6 [W] / 4.9 [W] LED On

29

MEMO MEMO

Digital Watchdog V3363D922 User manual

User Manual

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for future reference.

PRECAUTIONS

FCC COMPLIANCE

TROUBSHOOTING

EATURES*

EATURES*

EATURES*

EATURES*

EATURES*

IMENSIONS IN MILLIMETERS*

NSTALLATION*

NSTALLATION*

ONNECTION*

MAERA SETTINGS*

AMERA SETTING FOR SIDE OSD CONTROL BOARD*

2nd Video

JoyStick Key

ODULE OSD MENU*

SD MENU*

ODULE OSD MENU*

SD MENU*

ARRANTy INFORMATION*

IMITS AND EXCLUSIONS*

PECIFICATIONS*

PECIFICATIONS*

PECIFICATIONS*

PECIFICATIONS*

PECIFICATIONS*

Related manuals

Digital Watchdog

DWC-V3363D922

Digital Watchdog

DWC-V1363TIR

Digital Watchdog

DWC-V1382TIR

Digital Watchdog

DWC-V3367WD

Digital Watchdog

Infinity C233W

Digital Watchdog

DWC-LPR650

Digital Watchdog

B1362TIR650

Digital Watchdog

Infinity V3367WTIR

Digital Watchdog

Starlight V3363DH

Digital Watchdog

DWC-B1363D

Digital Watchdog

Starlight V3363D