Datalogic BC-80X0 Cradle Quick Reference Manual

Datalogic BC-80X0 Cradle builds a Cordless Reading System for collecting, decoding, and transmitting barcoded data. Connect the cradle to a Host PC via RS-232, USB, Wedge, or Pen cable for single-cradle point-to-point layouts. Alternatively, integrate it into a fixed scanner app via a C-BOX. The multi-cradle layouts are available through an RS-485 Network for BC-8060 models.

PDF

Documento

BC-80X0 Cradle

Quick Reference Guide

Datalogic Scanning, Inc.

959 Terry Street

Eugene, Oregon 97402

USA

Telephone: (541) 683-5700

Fax: (541) 345-7140

An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation.

Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A and the E.U. All other brand and product names referred to herein may be trademarks of their respective owners.

Patents

This product is covered by US Pat. 7,948,214 B2. Additional patents pending.

BC -80X0

USING THE BC-80X0 RADIO CRADLE

The BC-80X0 cradle, paired with one or more Powerscan™ M8300 readers, builds a Cordless Reading System for the collection, decoding and transmission of barcoded data.

It can be connected to a Host PC through an RS-232, USB, Wedge or Pen cable and is suited for single-cradle point-to-point layouts. It can also be connected to a C-BOX and therefore integrated into a fixed scanner application.

The BC-8060 models also allow multi-cradle layouts through an RS-485

Network. For this network connection refer to the Powerscan™ D8330/M8300

Reference Manual.

The label on the cradle contains LED indicators and a scan finder button.

When the button is pressed, the cradle transmits a “broadcast” message. All properly configured scanners (Radio RX Timeout set to keep the radio “awake”) that are linked to that base (through a bind or a join sequence) and within radio range coverage will emit a beep sequence once every 2 seconds for 30 seconds. This functionality is useful to:

- verify which scanners are linked to a certain base station

- detect a scanner forgotten somewhere

The LEDs signal the BC-80X0 status, as described in the following table:

LED STATUS

Aux

Host

Yellow On = BC-80X0 is powered through an external power supply.

Yellow Blinking = BC-80X0 transmission occurs over the Host port.

Yellow On = BC-80X0 is powered by the Host.

Yellow Blinking = BC-80X0 transmission occurs over the Host port.

Reader Green On = the reader battery is completely charged.

Red On = the reader battery is charging.

Orange Blinking = reader battery fault – replace battery.

Red / Green Alternatively Blinking = charging error - see Ref. Manual

Spare* Green On = the spare battery is completely charged.

Red On = the spare battery is charging.

Orange Blinking = spare battery fault – replace battery.

Red / Green Alternatively Blinking = charging error - see Ref. Manual

* This LED refers to the accessory SBS-8000 Spare Battery Slot when mounted to the BC-8060. Not available for BC-8010 models.

Figure 1 – Cradle Overview

Figure 2 – LEDs

DATALOGIC

To set up your BC-80X0 cradle you must:

1. Physically install the cradle.

2. Make all system connections.

3. Configure the BC-80X0 cradle.

INSTALLATION

MOUNTING THE BC-80X0 CRADLE

The cradle package contains the following items:

BC-80X0

BC-80X0 Quick Reference Guide

1 horizontal base

2 wall-mounting lock hinges

BC-8000 Antenna

2 adhesive strips

4 rubber feet

1 inclined base

The cradle can be mounted for portable or fixed desktop usage, or it can be fixed to a wall. The horizontal base allows portable and fixed desktop usage, while the inclined base provides desktop and wall mounting guaranteeing a comfortable handling of the Powerscan™ M8300 reader.

BC-80X0 Cradle mounted on the Horizontal Base

BC-80X0 Cradle mounted on the Inclined Base

Mounting

Tabs (4)

BC -80X0

Desktop mounting

For desktop usage, you can mount the cradle either on the horizontal base, for reduced overall dimensions, or on the inclined base for a more ergonomic taking out and insertion of the reader onto the cradle.

Horizontal base

Rubber Foot

Seat (4)

Mounting

Holes (2)

Adhesive

Strip Seat (2)

Mounting

Tabs (4)

Cable

Channels

Top View

Inclined base

Bottom View

Adhesive

Strip Seat (2)

Rubber

Foot Seat (4)

Mounting

Holes (4)

Top View Bottom View

Cable

Channels

DATALOGIC

PORTABLE DESKTOP USE

1. Correctly position the BC-80X0 onto the base by sliding it along the mounting tabs until aligned.

2. Carefully clean the rubber foot seats of the base to remove any impurities that could reduce adhesion.

3. Remove the protective plastic from the rubber feet and stick them onto the bottom surface of the base.

4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.

FIXED DESKTOP USE

For fixed desktop installation, use the adhesive strips or fixing screws (not provided) according to your needs.

For mounting with adhesive strips:

1. Position the cradle onto the base by sliding it along the mounting tabs until aligned.

2. Carefully clean the adhesive strip seats of the base to remove any impurities that could reduce adhesion.

3. Remove the protective plastic from one side of the adhesive strips and stick them onto the base surface.

4. Position the cables to be connected to the BC-80X0 cradle along the dedicated channels, as shown in the figures below:

Horizontal Base Inclined Base

BC -80X0

5. Remove the plastic from the other side of the strips and affix the base to the table.

6. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.

For mounting with screws:

1. Position the cables to be connected to the BC-80X0 cradle along the dedicated channels, as shown in the figures below:

2. Position the base on the table and affix it by means of the screws (not provided).

3. Position the cradle on the base by sliding it along the mounting tabs until aligned.

4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.

Wall Mounting

1. Remove the yellow caps and insert the two wall mounting lock hinges provided with your cradle.

DATALOGIC

2. Position the cables to be connected to the BC-80X0 cradle along the

dedicated channels (see figures at page 4).

If using the adhesive strips:

3. Carefully clean the adhesive strip seats of the base to remove any impurities that could reduce adhesion.

4. Remove the protective plastic from one side of the adhesive strips and stick them onto the base surface.

5. Remove the plastic from the other side of the strips and affix the base to the wall as indicated in the figure below.

If using the mounting screws:

3. Using the mounting holes on the base as a pattern, mark the wall where you desire to mount the

BC-80X0.

4. Drill the appropriate size holes and insert the threaded dowels

(not provided) into the holes.

5. Position the base on the wall as indicated in the figure below and affix it by means of the screws

(not provided).

Inclined Base Wall-mounting

6. Attach the cradle on the base by sliding it along the mounting tabs until aligned.

7. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.

BC -80X0

APPLYING RAPID POINT-TO-POINT CONFIGURATION

LABEL (OPTIONAL)

A pre-printed barcode label is included in the package for rapid configuration of point-topoint applications. If you wish to use this method, apply this label to the seat provided on the BC-80X0 cradle as shown in the figure. See the Powerscan™ M8300 Quick

Reference Manual for the configuration procedure.

SYSTEM CONNECTIONS

Connections should always be made with power off!

CAUTION

The BC-80X0 cradle provides two interface connectors and a power supply connector as shown in the figure on the next page:

Power Supply

RS-485

(BC-8060 only)

MULTI-INTERFACE

RS-232, USB, Wedge,

PEN Emulation

The RS-485 Network connection is available only on BC-8060 models. For details about this type of connection, refer to the Powerscan™ D8330/M8300

Reference Manual.

To connect the BC-80X0 cradle to the Host through the multi-interface connector, use the cable corresponding to the desired interface type.

DATALOGIC

CONNECTING AND DISCONNECTING THE BC-80X0

INTERFACE CABLE

The BC-80X0 can be connected to a Host by means of an RS-232, USB, Wedge or Pen cable, which must be simply plugged into the Host connector, visible on the front panel of the cradle.

To disconnect the cable, insert a paper clip or other similar object into the hole corresponding to the Host connector on the body of the cradle. Push down on the clip while unplugging the cable. Refer to the following figure:

Multi-standard interface

RS-232, USB, WEDGE, or

PEN Emulation to Host

Power

Connecting/Disconnecting the Cable

RS-232

USB

WEDGE

BC -80X0

PEN

Powerscan™ M

JOIN

BIND

BC-80X0

C-BOX

C-BOX

Scanner

System cables to Host

DATALOGIC

BC-80X0 CONFIGURATION

The BC-80X0 configuration can be performed in three ways: by using the

Datalogic Aladdin™ software configuration program, by sending configuration strings from the Host PC via the RS-232 or USB-COM interface or by reading configuration barcodes with the Powerscan™ M reader.

DATALOGIC ALADDIN™

Datalogic Aladdin™ is a multi-platform utility program providing a quick and user-friendly configuration method via the RS-232/USB-COM interface.

It also allows upgrading the software of the connected device (see the Datalogic

Aladdin™ Help On-Line for more details).

SERIAL CONFIGURATION

By connecting the BC-80X0 to a PC through an RS-232 or USB-COM interface cable it is possible to send configuration strings from the PC to BC-80X0.

CONFIGURATION BARCODES

Once you have performed system connection and Powerscan™ M reader configuration, you can configure the BC-80X0 cradle by reading configuration barcodes. Apply power to the BC-80X0.

For Powerscan™ M configuration, refer to the “Powerscan™ M8300 Quick

Reference”.

To configure the BC-80X0 using the Powerscan™ M reader (the one paired to the cradle with the Bind command), follow the procedure according to the interface selected.

RESTORE DEFAULT

RESTORE BC-80X0 DEFAULT

Ì$+RX0$-qÎ

To change the defaults refer to the "Powerscan™ D8330/M8300 Reference

Manual", or to the Datalogic Aladdin™ Configuration program, both downloadable from the website.

BC -80X0

INTERFACE SELECTION

Select one of the interface codes according to your application.

USB INTERFACE SELECTION

USB-KBD

Ì$+UA03$-:Î

USB-COM*

Ì$+UA02$-4Î

Ì$+UA00$-(Î

USB-KBD – ALT-mode

Ì$+UA04$-@Î

USB-IBM-Hand Held

Ì$+UA01$-.Î

USB-IBM Table top

USB KBD-APPLE

* When configuring USB-COM, the relevant files and drivers must be installed from the USB Device Installation Software, which can be downloaded from the web site http://www.scanning.datalogic.com.

PEN EMULATION INTERFACE SELECTION

PEN

Ì$+CP6$-BÎ

DATALOGIC

INTERFACE SELECTION

Select one of the interface codes according to your application.

RS-232 INTERFACE SELECTION

RS-232 Standard

Ì$+CP0$-$Î

Fujitsu

Ì$+CM1$-ÈÎ

Nixdorf Mode A

Ì$+CM2EC0$->Î

ICL Mode

Ì$+CM0$-ÃÎ

WEDGE INTERFACE SELECTION

Wedge IBM AT or PS/2 PCs

Ì$+CP500$-aÎ

PC Notebook

PC Notebook - ALT mode

Ì$+CP508$-2Î

Ì$+CP505$-ÈÎ

IBM AT - ALT mode

Ì$+CP507$-+Î

Interfaces for IBM XT and IBM Terminals 3151, 347X and 348X can be selected from the PowerScan D8330/M8300 Reference Manual available online at http://www.scanning.datalogic.com

BC -80X0

KEYBOARD NATIONALITY

USB-KBD and Wedge users should select one of the following wedge keyboard nationality codes according to your keyboard.

Belge

Ì$+FJ7$-8Î

Deutsch

Ì$+FJ3$-$Î

English

Ì$+FJ4$-)Î

Español

Ì$+FJ6$-3Î

Français

Ì$+FJ2$-ÊÎ

Italiano

Ì$+FJ1$-ÅÎ

Svenskt

Ì$+FJ5$-.Î

USA (Default)

Ì$+FJ0$-|Î

DATALOGIC

The following Keyboard Nationality selections are only valid for IBM AT compatible PCs:

Japanese

Ì$+FJ8$-=Î

Russian (Latin)

Ì$+FJ9$-BÎ

Russian (Cyrillic)

Ì$+FJA$-jÎ

Hungarian

Ì$+FJB$-oÎ

Slovenian, Croatian, Serbian (Latin)

Ì$+FJC$-tÎ

Romanian

Ì$+FJD$-yÎ

Czech Republic

Ì$+FJE$-~Î

BC -80X0

DATA FORMAT TERMINATORS

For your convenience, some common Terminators are given below. For other

Header/Terminators selections, Data Format and Advanced Data Format parameters see the Powerscan™ D8330/M8300 Reference Manual.

CR-LF

Ì$+EA120D0A$-ÃÎ

Enter

Ì$+EA1183$-0Î

Tab

Ì$+EA1184$-8Î

None

Ì$+EA10$-dÎ

DATALOGIC

BC-80X0 DEFAULT CONFIGURATION

USB-KBD DEFAULT SETTINGS

USA keyboard, FIFO enabled, inter-character and inter-code delays disabled,

USB keyboard speed normal.

DATA FORMAT

: code identifier disabled, code length not transmitted, character replacement disabled, reader and cradle address stamping disabled, reader and cradle address delimiter disabled, time stamping disabled, time stamping delimiter disabled, no header, terminator = ENTER.

RS-232 DEFAULT SETTINGS

9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, ack/nack protocol disabled, FIFO enabled, delay disabled, 5 sec. rx timeout

DATA FORMAT

WEDGE DEFAULT SETTINGS

USA keyboard, Caps Lock off, Caps Lock Auto-Recognition enabled, num lock unchanged, inter-character and intercode delay disabled, control character emulation = ctrl+shift+key.

DATA FORMAT

PEN DEFAULT SETTINGS

Interpret operating mode, conversion to code 39, output level normal, idle level normal, minimum output pulse 600 s, overflow medium, inter-block delay disabled.

NETWORK PARAMETERS

RS-485 network disabled (for BC-8000 only).

BC -80X0

OPERATING TEST

Read the TEST codes below.

EAN-8

12 34 5 670

EAN-13

1 2 3 4 5 6 7 0 0 0 9 9 2

Code 39 (Normal)

1 7 1 6 2

Code 128 t e s t

Interleaved 2 of 5

0 1 2 3 4 5 6 7 8 4

YOUR SYSTEM IS NOW READY TO READ CODES AND TO SEND THE

DATA TO THE HOST.

DATALOGIC

TECHNICAL FEATURES

BC-80X0

Electrical Features

Supply Voltage

External Power

Host Power

Power Consumption

External Power

Host Power

Indicators

Time of Recharge

External Power

Host Power

Radio Features

Radio frequency

Bit Rate

Range (in open air)

Environmental Features

Working Temperature

Radio

Battery Charging

Storage Temperature

Humidity

Protection Class

Mechanical Features

Weight without mounting base

Dimensions (without antenna)

Material

10..30 VDC

5 VDC ±10% max. 10 W (charging) * max. 500 mA (charging)

Ext. Power/Data yellow LED

Host Power/Data yellow LED

Reader batt. state green/red LED

Spare batt. state green/red LED (BC-8060 only)

beeper

max. 4 hours with 2150 mAh Li-Ion battery max. 10 hours with 2150 mAh Li-Ion battery

European Models

433.92 MHz

19200 baud

50 m

USA Models

910 MHz

36800 baud

30 m

-20° to +50 °C / -4° to +122 °F

0° to +40 °C / +32° to +104 °F

-20° to +70 °C / -4° to +158 °F

90 % non condensing

IP40 about 380 g / 13.4 oz

240 x 108 x 95 mm / 9.44 x 4.25 x 3.74 in

ABS

* Having a switching regulator inside, the BC-80X0 draws the same power, regardless of the supply voltage. i.e. as the input voltage increases the current drawn decreases.

System Configuration

Max number of devices per base station

Max number of devices in the same reading area

BC-80X0

2000

STARGATE™

255

Max number of base stations in network

BC-8060 STARGATE™

16 (including cradle Master)

BC -80X0

WARRANTY

DATALOGIC SCANNING LIMITED FACTORY WARRANTY

Warranty Coverage

Datalogic warranties this product against defects in workmanship and materials, for a period of 3 years from the date of shipment, provided that the product is operated under normal and proper conditions.

Datalogic Scanning (“Datalogic”) hardware products are warranted against defects in material and workmanship under normal and proper use. The liability of Datalogic under this warranty is limited to furnishing the labor and parts necessary to remedy any defect covered by this warranty and restore the product to its normal operating condition. Repair or replacement of product during the warranty does not extend the original warranty term. Products are sold on the basis of specifications applicable at the time of manufacture and

Datalogic has no obligation to modify or update products once sold.

If Datalogic determines that a product has defects in material or workmanship,

Datalogic shall, at its sole option repair or replace the product without additional charge for parts and labor, or credit or refund the defective products duly returned to Datalogic. To perform repairs, Datalogic may use new or reconditioned parts, components, subassemblies or products that have been tested as meeting applicable specifications for equivalent new material and products. Customer will allow Datalogic to scrap all parts removed from the repaired product. The warranty period shall extend from the date of shipment from Datalogic for the duration published by Datalogic for the product at the time of purchase (Warranty period). Datalogic warrants repaired hardware devices against defects in workmanship and materials on the repaired assembly for a 90 day period starting from the date of shipment of the repaired product from Datalogic or until the expiration of the original warranty period, whichever is longer. Datalogic does not guarantee, and it is not responsible for, the maintenance of, damage to, or loss of configurations, data, and applications on the repaired units and at its sole discretion can return the units in the “factory default” configuration or with any software or firmware update available at the time of the repair (other than the firmware or software installed during the manufacture of the product). Customer accepts responsibility to maintain a back up copy of its software and data.

Warranty Claims Process

In order to obtain service under the Factory Warranty, Customer must notify

Datalogic of the claimed defect before the expiration of the applicable Warranty period and obtain from Datalogic a return authorization number (RMA) for return of the product to a designated Datalogic service center. If Datalogic determines

Customer’s claim is valid, Datalogic will repair or replace product without additional charge for parts and labor. Customer shall be responsible for packaging and shipping the product to the designated Datalogic service center, with shipping charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is to a location within the country in which the

Datalogic service center is located. Customer shall be responsible for paying all

DATALOGIC shipping charges, duties, taxes, and any other charges for products returned to any other locations. Failure to follow the applicable RMA policy, may result in a processing fee. Customer shall be responsible for return shipment expenses for products which Datalogic, at its sole discretion, determines are not defective or eligible for warranty repair.

Warranty Exclusions

The Datalogic Factory Warranty shall not apply to:

(i)

any product which has been damaged, modified, altered, repaired or upgraded by other than Datalogic service personnel or its authorized representatives;

(ii)

any claimed defect, failure or damage which Datalogic determines was caused by faulty operations, improper use, abuse, misuse, wear and tear, negligence, improper storage or use of parts or accessories not approved or supplied by Datalogic;

(iii)

any claimed defect or damage caused by the use of product with any other instrument, equipment or apparatus;

(iv)

any claimed defect or damage caused by the failure to provide proper maintenance, including but not limited to cleaning the upper window in accordance with product manual;

(v)

any defect or damage caused by natural or man-made disaster such as but not limited to fire, water damage, floods, other natural disasters, vandalism or abusive events that would cause internal and external component damage or destruction of the whole unit, consumable items;

(vi)

any damage or malfunctioning caused by non-restoring action as for example firmware or software upgrades, software or hardware reconfigurations etc.;

(vii)

the replacement of upper window/cartridge due to scratching, stains or other degradation and/or

(viii)

any consumable or equivalent (e.g., cables, power supply, batteries, keypads, touch screen, triggers etc.).

No Assignment

Customer may not assign or otherwise transfer its rights or obligations under this warranty except to a purchaser or transferee of product. No attempted assignment or transfer in violation of this provision shall be valid or binding upon

Datalogic.

DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, ORAL OR WRITTEN, STATUTORY

OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE

FOR ANY DAMAGES SUSTAINED BY CUSTOMER ARISING FROM

DELAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UNDER THE

ABOVE. THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT IS

THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY

CLAIMS. UNDER NO CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO

BC -80X0

CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY

INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT

DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE

NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

Risk of Loss

Customer shall bear risk of loss or damage for product in transit to Datalogic.

Datalogic shall assume risk of loss or damage for product in Datalogic’s possession. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment.

SERVICE AND SUPPORT

Datalogic provides several services as well as technical support through its website. Log on to www.scanning.datalogic.com and click on the links indicated for further information including:

PRODUCTS

Search through the links to arrive at your product page where you can download specific Manuals and Software & Utilities including:

- Datalogic Aladdin™, a multi-platform utility program that allows device configuration using a PC. It provides RS-232 interface configuration as well as configuration barcode printing.

SERVICE & SUPPORT

- Technical Support - Product documentation and programming guides and Technical Support Department in the world

- Service Programs - Warranty Extensions and Maintenance

Agreements

- Repair Services - Flat Rate Repairs and Return Material Authorization

(RMA) Repairs.

- Downloads – Manuals & Documentation, Data Sheets, Product

Catalogues, etc.

CONTACT US

Information Request Form and Sales & Service Network

DATALOGIC

COMPLIANCE

This device must be opened by qualified personnel only.

POWER SUPPLY

This device is intended to be supplied by a UL Listed/CSA Certified Power Unit marked "Class 2" or LPS power source rated 10-30 V DC, minimum 1 A, which supplies power directly to the cradle.

FCC COMPLIANCE

Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.

This device contains FCC ID U4F0015.

RADIO COMPLIANCE

Contact the competent authority responsible for the management of radio frequency devices of your country to verify any possible restrictions or licenses required.

Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm

for further information.

BC -80X0

WEEE COMPLIANCE

Waste Electrical and Electronic Equipment (WEEE)

Statement

English

For information about the disposal of Waste Electrical and Electronic Equipment

(WEEE), please refer to the website at www.scanning.datalogic.com

Italian

Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.scanning.datalogic.com

French

Pour toute information relative à l’élimination des déchets électroniques

(WEEE), veuillez consulter le site internet www.scanning.datalogic.com

German

Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE) erhalten Sie auf der Webseite www.scanning.datalogic.com

Spanish

Si desea información acerca de los procedimientos para el desecho de los residuos del equipo eléctrico y electrónico (WEEE), visite la página Web www.scanning.datalogic.com

Portuguese

Para informações sobre a disposição de Sucatagem de Equipamentos Elétricos e Eletrônicos (WEEE -Waste Electrical and Electronic Equipment), consultar o site web www.scanning.datalogic.com

Chinese

有关处理废弃电气电子设备 (WEEE)的信息，请参考Datalogic公司的网站： http://www.scanning.datalogic.com。

Japanese

廃電気電子機器(ＷＥＥＥ)の処理についての関連事項はDatalogicのサイト www.scanning.datalogic.com,

をご参照下さい。

DATALOGIC

NOTES

Datalogic Scanning, Inc.

959 Terry Street

Eugene, OR 97402

USA

dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el

BC-80X0, RF Base Charger

e tutti i suoi modelli and all its models et tous ses modèles und seine Modelle y todos sus modelos sono conformi alla Direttiva del Consiglio Europeo sottoelencata: are in conformity with the requirements of the European Council Directive listed below: sont conformes aux spécifications de la Directive de l'Union Européenne ci-dessous: der nachstehenden angeführten Direktive des Europäischen Rats entsprechen: cumple con los requisitos de la Directiva del Consejo Europeo, según la lista siguiente:

1999/5/EEC R&TTE

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:

This declaration is based upon compliance of the products to the following standards:

Cette déclaration repose sur la conformité des produits aux normes suivantes:

Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:

Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:

ETSI EN 301 489-3 v1.4.1, August 2002:

LECTRO

AGNETIC

OMPATIBILITY AND

ADIO

SPECTRUM

ATTERS

(ERM); E

LECTRO

AGNETIC

OMPATIBILITY

(EMC)

STANDARD FOR RADIO EQUIPMENT

AND SERVICES

; P

ART

3: S

PECIFIC CONDITIONS FOR

ETSI EN 300 220-3 v1.1.1, September 2000:

HORT

-R

ANGE

EVICES

(SRD)

OPERATING ON

FREQUENCIES BETWEEN

Z AND

40 GH

LECTROMAGNETIC COMPATIBILITY AND

ADIO

SPECTRUM

ATTERS

(ERM); S

HORT

ANGE

EVICES

(SRD); R

ADIO EQUIPMENT TO BE USED IN THE

25 MH

Z TO

1000 MH

Z FREQUENCY RANGE WITH POWER LEVELS

RANGING UP TO

500

W; P

ART

3: H

ARMONIZED

COVERING ESSENTIAL REQUIREMENTS UNDER ARTICLE

3.2

EN 60950-1, December 2001:

December 20, 2007

OF THE

R&TTE D

IRECTIVE

NFORMATION TECHNOLOGY EQUIPMENT

– S

AFETY

–

ART

1: G

ENERAL REQUIREMENTS

Australia

Datalogic Scanning Pty Ltd

Telephone: [61] (2) 9870 3200 [email protected]

France and Benelux

Datalogic Scanning SAS

Telephone: [33].01.64.86.71.00

[email protected]

Germany

Datalogic Scanning GmbH

Telephone: 49 (0) 61 51/93 58-0 [email protected]

India

Datalogic Scanning India

Telephone: 91- 22 - 64504739 [email protected]

Italy

Datalogic Scanning SpA

Telephone: [39] (0) 39/62903.1

[email protected]

Japan

Datalogic Scanning KK

Telephone: 81 (0)3 3491 6761 [email protected]

Latin America

Datalogic Scanning, Inc

Telephone: (305) 742-2206 [email protected]

Singapore

Datalogic Scanning Singapore PTE LTD

Telephone: (65) 6435-1311 [email protected]

Iberia

Datalogic Scanning SAS Sucursal en España

Telephone: 34 91 746 28 60 [email protected]

United Kingdom

Datalogic Scanning LTD

Telephone: 44 (0) 1582 464900 [email protected]

www.scanning.datalogic.com

Datalogic Scanning, Inc.

959 Terry Street

Eugene, OR 97402

USA

Telephone: (541) 683-5700

Fax: (541) 345-7140

820042814 (Rev. C) July-2011