advertisement
CH-506TX & RX
HDBaseT™ HDMI over Single CAT5e/6/7 Extender
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
REVISION HISTORY
VS2
VR3
VR4
VR5
VERSION NO.
DATE DD/MM/YY SUMMARY OF CHANGE
VR0 12/12/11 Preliminary release
VS1 26/04/12 Updated format, diagrams and statements
VR6
26/07/12
28/09/12
10/04/14
13/03/14
28/04/15
IR cable updated
Add HDBaseT Lite version
HDMI I/O cable distance
IR cable quantity
Supported resolution
CONTENTS
1. Introduction ............................................ 1
2. Applications ........................................... 1
3. Package Contents ................................ 1
4. System Requirements ............................ 1
5. Features .................................................. 2
6. Operation Controls and Functions ....... 3
6.1 Transmitter Front and Rear Panels ..3
6.2 Receiver Front and Rear Panels .....4
6.3 D-Sub 9-Pin Definitions .....................5
6.4 IR Cable Pin Assignment..................5
7. Connection Diagram ............................ 6
8. Specifications ........................................ 7
9. Acronyms ............................................... 8
1. INTRODUCTION
This HDBaseT™ HDMI over Single CAT5e/6/7 Transmitter and Receiver
Set can send uncompressed audio/video over a single run of
CAT5e/6/7 cable up to 100m (1080p) and has the added benefit of control through the built-in RS-232 and 2-way IR.
2. APPLICATIONS
• Domestic HDMI installation
• University lecturing systems
• Retail showroom systems
• Conference presentation and control
3. PACKAGE CONTENTS
• 1×HDMI over Single CAT5e/6/7 Transmitter
• 1×HDMI over Single CAT5e/6/7 Receiver
• 1×IR Blaster
• 1×IR Extender
• 1×3.5 mm Mini-jack to RS-232 Female Cable
• 1×3.5 mm Mini-jack to RS-232 Male Cable
• 2×5 V/2.6 A DC Power Adaptor
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as a DVD or Blu-ray player and HDMI equipped display (TV or monitor). HDMI and CAT5e/5/7 connection cables.
1
5. FEATURES
• HDMI including 3D and 4K2K (Ultra HD) support, HDCP and DVI compliant
• Supports HDCP repeater and CEC functions
• Simultaneous transmission of uncompressed data over a single
CAT5e/6/7 cable up to 100 m/328 ft (1080p@60 Hz/8-bit), 40m (3D) or 20m (4K2K)
• Supports HD resolutions up to 1080p@60Hz/36-bit and Ultra HD (4K2K)
• Audio support up to LPCM 7.1CH, Dolby TrueHD and DTS-HD Master
Audio
• Supports HDBaseT Technology including 2-way IR and RS-232
• Installation friendly
Note: This system was tested with CAT6/23AWG cable. Results may vary with cables of different specifications.
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
Front
IR2 Extender
DC 5V
HDMI In
7
Power
Link
RS232 In IR1 Blaster
Rear
CAT 5e /6 Out
1 2 3 4 5 6 8
1
RS232 In: Connect to a PC/laptop or RS-232 enabled device
(with supplied 3.5 mm mini-jack to D-sub 9-pin adaptor) for the transmission of RS-232 commands.
2
IR2 Extender: Connect to the supplied IR extender cable for IR signal reception. Ensure that remote control being used is within the direct line-of-sight of the IR extender.
3
IR1 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line-of-sight of the equipment to be controlled.
4
HDMI In: Connect to the HDMI source equipment such as a DVD or
Blu-ray player.
5
DC 5V: Connect the 5 V DC power supply to the unit and plug the adaptor into an AC outlet.
6
Link LED: The yellow LED will illuminate when both the input and output CAT5e/6/7 signals are connected.
7
Power LED: This green LED will illuminate when the device is connected to a power supply.
8
CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7 cable for transmission of all data signals.
3
6.2 Receiver Front and Rear Panels
Front
IR1 Extender DC 5V
HDMI Out
7
Power
Link
RS232 Out IR2 Blaster
Rear
CAT 5e /6 In
1 2 3 4 5 6 8
1
RS232 Out: Connect to the device that is to be controlled (with the supplied 3.5mm mini-jack to D-sub 9-pin adaptor) by RS-232 commands.
2
IR1 Extender: Connect to the supplied IR extender cable for IR signal reception. Ensure that the remote being used is within the direct line-of-sight of the IR extender.
3
IR2 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line of sight of the equipment to be controlled.
4
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the HDMI input source signal.
5
DC 5V: Plug the 5 V DC power supply into the unit and connect the adaptor to an AC outlet.
6
Link LED: The yellow LED will illuminate when both the input and output CAT5e/6/7 signals are connected.
7
Power LED: This green LED will illuminate when the device is connected to a power supply.
8
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7 cable for transmission of all data signals.
4
6.3 D-Sub 9-Pin Definitions
6
7
4
5
PIN
1
2
3
8
9
DEFINE TX/RX
N/C
TxD/RxD
RxD/TxD
N/C
GND
N/C
N/C
N/C
N/C
6.4 IR Cable Pin Assignment
IR Blaster
2
3
1 Power
IR Signal
NC
IR Extender
1
2
3
IR Signal
Power
Grounding
5
7. CONNECTION DIAGRAM
RS-232 Equipped
PC or Notebook
3m 3m
60°
DVD/Blu-ray Player
1.5m
60°
IR Blaster 1
IR Extender 2
IR Extender 1
HDMI
Input
RS-232
IR2 Extender
RS232 In IR1 Blaster
HDMI In
DC 5V
Power
Link
CAT 5e /6 Out
TX
Power Supply
CAT5e/6/7
Cable (100m)
Power Supply
DC 5V
Power
Link
CAT 5e /6 In
IR1 Extender
RS232 Out IR2 Blaster
HDMI Out
RX
3m
60°
3m
1.5m
IR Blaster 2
60°
RS-232
HDMI
Output
RS-232 Device to be Controlled
Display
6
8. SPECIFICATIONS
Video Bandwidth
Transmitter
Input Ports
Output Ports
Receiver
Input Ports
Output Ports
CAT5e/6/7 Cable
Distance
HDMI Cable Input
Distance
HDMI Cable Output
Distance
ESD Protection
340 MHz/10.2 Gbps
1×HDMI, 1×IR Extender, 1×RS-232
1×CAT5e/6/7, 1×IR Blaster
1×CAT5e/6/7, 1×IR Extender
1×HDMI, 1×IR Blaster, 1×RS-232
Up to 100 m
10 m@8-bit, 6 m@12-bit
10 m@8-bit, 6 m@12-bit
Power Supply
Human-body Model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
5 V/2.6 A DC (US/EU standards, CE/FCC/UL certified)
IR Frequency
Dimensions
Weight
Chassis Material
30~50 kHz
71 mm (W)×79 mm (D)×23 mm (H)/Each
240 g/TX, 245 g/RX
Aluminum
Color
Black
Operating Temperature 0°C~40°C/32°F~104°F
Storage Temperature
Relative Humidity
Power Consumption
−20°C~60°C/−4°F~140°F
20~90 % RH (non-condensing)
3 W/TX, 6 W/RX
7
9. ACRONYMS
ACRONYM
CAT5e
CAT6
CAT7
CEC
DVI
HDCP
HDMI
IR
COMPLETE TERM
Category 5 Cable
Category 6 Cable
Category 7 Cable
Consumer Electronics Control
Digital Visual Interface
High-bandwidth Digital Content Protection
High Definition Multimedia Interface
Infrared
8
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
advertisement
Related manuals
advertisement