advertisement
▼
Scroll to page 2
of 94
T18.... T24.... T30.... 9000649275 5 INSTALLATION INSTRUCTIONS ............................................................................... 4 INSTRUCTIONS D’INSTALLATION ............................................................................ 34 INSTRUCCIONES DE INSTALACIÓN ......................................................................... 64 3 Table of Contents IMPORTANT SAFETY INSTRUCTIONS .............. 5 Installation options .............................................. 6 Individual appliance .................................................. 6 Side-by-Side ................................................................ 6 Individual appliances with partition ........................ 6 Individual appliance at the end of the kitchen ..... 6 Installation ............................................................ 7 Installation room.......................................................... 1. Attaching the anti-tip-brackets .......... 13 2. Attaching an alternative anti-tip-device ....................................... 14 3. Attaching an edge protection ........... 14 4. Attaching the fastening sheets (lateral) ................................................... 14 5. Pushing the appliance into the installation enclosure ................... 15 7 1. Aligning the appliance in the installation enclosure ................... 16 Stable installation ...................................................... 7 2. Installation enclosure ................................................ 7 Attaching the appliance to the installation enclosure ................... 16 Furniture ...................................................................... 7 1. Attaching the toe kick panel ............. 18 Floor ............................................................................. 7 2. Aligning the base panel ..................... 18 Aligning the appliance .............................................. 7 3. Switching the appliance ON ............. 19 Connecting the power ......................................... 8 4. Preparing the door panels ................ 19 5. Loading the appliance door .............. 19 Grounding instruction ............................................... 8 6. Additional grounding procedure ............................. 8 Removing the installation support part .......................................... 19 Connecting the water .......................................... 8 7. Attaching the adjusting rail to the door panel ................................ 20 Installation dimensions ....................................... 9 8. Attaching the fixation strips to the door panel ................................ 20 9. Attaching the door panel ................... 21 Required accessories and tools ......................... 10 Supplied accessories ............................................... 10 Optional accessories ................................................ 10 10. Attaching the lower bracket .............. 22 11. Attaching the strips ............................. 23 Other required accessories ..................................... 10 Other ............................................................................ 10 12. Adjusting the door spring .................. 23 Special installation .............................................. 24 Tools ............................................................................ 10 Changing over the door hinges ............... 24 Installation instructions ...................................... 11 Removing/changing over the sealing mat ............................................ 27 1. Checking the installation enclosure .............................................. 11 Side-by-Side installation ............................. 27 2. Removing the packaging .................. 11 Preparing to connect the water ................ 30 3. Transport of the appliance ................ 12 Connecting the water to the appliance ..... 31 4. Installation preparation ...................... 12 Aligning the ice-water dispenser .............. 31 5. Special installation .............................. 12 Attaching the cover strips ......................... 32 Adjusting the door opening angle ........... 33 4 IMPORTANT SAFETY INSTRUCTIONS , WARNING These appliances are top-heavy and must be secured to prevent the possibility of tipping forward. Anti-tip protection is required. Keep doors closed until the appliance is completely installed and secured per installation instructions. Due to the weight and size of this appliance, and to reduce the risk of personal injury or damage to the product – TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION. General These installation instructions are intended for use by qualified installers. All connections for water, electrical power and grounding must comply with local codes and ordinances and be made by licensed personnel when required. In the absence of a local code: In the U.S.A., in accordance with the National Electric Code, ANSI/NFPA70 – latest edition/State and Municipal codes and/or local codes. In Canada, in accordance with the Canadian Electric Code C22.1 – latest edition/Provincial and Municipal codes and/or local codes. This appliance must be properly grounded. See the section on “Connecting the power”. Use this appliance only for its intended purpose. Definitions Immediately repair or replace electric service cords that become frayed or damaged. , This indicates that death or serious injuries may occur as a result of not observing this warning. Unplug the appliance or switch off the fuse before cleaning or making repairs. Repairs should be made by a qualified service technician. WARNING: , CAUTION: This indicates that minor or moderate injuries or damage may occur as a result of not observing this warning. NOTE Installation of this appliance requires basic mechanical, carpentry and plumbing skills. Note: Proper installation is the responsibility of the installer. This is used to draw the user's attention to something in particular. Product failure due to improper installation is not covered under the Appliance Warranty. See the Owner's Manual for warranty information. IMPORTANT Save these instructions for local inspector's use. Observe all governing codes and ordinances. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions with your Owner's Manual for future reference. 5 Installation options There are many different installation options. Individual appliances with partition These are limited only by the design of the kitchen. See also “Kitchen Design Quick Reference”. Individual appliance Side-by-Side When dimensioning the partition for model 4, note the thickness of the door panels to prevent damage if the doors are opened at the same time. Use the Heater Kit for Side-by-Side Installation if the gap between the appliances is less than 6" (160 mm). See the section on “Required accessories and tools/Optional accessories”. Minimum thickness of the partition 5/8" (16 mm). Individual appliance at the end of the kitchen If one side of the appliance is visible, a side panel must be used. The side panel must be connected firmly to the wall, the floor and overhead cabinet/fixtures before the appliance is placed in the installation enclosure. The dimensions of the side panel are taken from the opposite installation enclosure wall. During installation ensure that the installation enclosure is square and the proper size. 6 Installation , WARNING: Do not install the appliance: outdoors, in an environment with dripping water, in rooms which are less than 32 °F (0 °C). Appliance is very heavy: Refrigerator 24" approx. 310 Ibs/140 kg Refrigerator 30" approx. 350 Ibs/158 kg Freezer 18" approx. 255 Ibs/115 kg* Freezer 24" approx. 300 Ibs/135 kg* Freezer 30" approx. 335 Ibs/150 kg* Wine unit 18 "approx. 300 Ibs/135 kg Wine unit 24 "approx. 360 Ibs/160 kg (* without Water Dispenser) Installation room The appliance should be installed in a dry, ventilated room. The ambient temperature should not drop below 55 °F (13 °C) or rise above 110 °F (43 °C), otherwise malfunctions may occur. The installation location should not be exposed to direct sunlight and not placed near a heat source, such as an oven, radiator, etc. If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following minimum distances from the heat source: 11/4" (30 mm) from an electric range, 12" (300 mm) from a gas range. It is important to observe the specified dimensions of the installation enclosure for a trouble-free installation of the appliance. In particular ensure that the installation enclosure is square. Squareness can be checked by suitable means, e.g. level, diagonal measurements, etc. Furniture The new appliance must be screwed securely to adjacent and overhead furniture. For this reason it is essential that all attachable furniture are connected securely to the floor or the wall by suitable means. Floor , WARNING: A fully-loaded appliance is very heavy – for the loadbearing capacity minimum see the following: Refrigerator 24" approx. 890 Ibs/400 kg Refrigerator 30" approx. 1110 Ibs/500 kg Freezer 18" approx. 560 Ibs/250 kg* Freezer 24" approx. 780 Ibs/350 kg* Freezer 30" approx. 950 Ibs/425 kg* Wine unit 18" approx. 550 Ibs/245 kg Wine unit 24" approx. 694 Ibs/310 kg (* without Water Dispenser) To ensure that the appliance is installed securely and functions properly, the floor must be flat and level. Stable installation The floor must be made of a hard, rigid material. The appliance is very heavy and has a tendency to tilt forwards when the appliance door is opened. Do not open the door until there is no possibility of the appliance tilting over. The floor in the installation area must be at the same level as the rest of the room (no step up or down). The safest method of installing the appliance in a stable position is to use the supplied anti-tip devices. If the installation enclosure is adequately stable and the appliance can be attached securely to the upper and side walls of the installation enclosure, this may provide additional stability. A prerequisite for this is always a firm connection between the installation enclosure and back wall! On account of the heavy weight of a fully loaded appliance, a load-bearing floor is required. If in doubt, contact an architect or a building expert. Aligning the appliance To ensure that the appliance functions correctly, it must be levelled properly. If the appliance is not level, water may flow out of the ice maker, ice cubes may be irregular or the doors may not close properly. If in doubt, contact an architect or a building expert. Installation enclosure Note: It is strongly recommended the top panel of the niche be of solid material at least 5/8" (16 mm) thickness. If, for some reasons, a seperate niche cabinet is created, make sure that the furniture return area is at least 4" deep. 7 Additional grounding procedure Connecting the power , Some local regulations may require a seperate ground. In such cases, the required ground wire, clamp and screw are available as a separate accessory and must be purchased seperately. WARNING: Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Never ground the appliance to plastic plumbing lines, gas lines or water pipes. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Follow all state and local codes or NEC. The appliance comes with a UL listed 3 wire power supply cord. The appliance requires a 3-wire receptacle. The receptacle must be installed by a licensed electrician only. The receptacle must be a 15 A breaker or fuse. Connecting the water , CAUTION: Only connect the appliance to drinking water! A cold water connection is required for operation of the automatic ice maker. The water pressure must be between 25 and 120 psi. (1.72–8.25 bar). The installation must comply with local plumbing regulations. A separate shut-off valve must be installed for the appliance water connection. Do not use a self-piercing valve! Appliance Maximal load at one time Refrigerator 24" 2.0 Ampere Refrigerator 30" 2.0 Ampere Freezer 18" (incl. IceMaker) 3.5 Ampere Freezer 24" (incl. IceMaker) 4.0 Ampere Freezer 30" (incl. IceMaker) 4.5 Ampere The supply pipe can be located at the side on the right (a), at the side on the left (b) or underneath (c). Wine unit 18" 2.0 Ampere Wine unit 24" 2.0 Ampere Maximum outer diameter of the water pipe (without fittings): 3/8" (9.5 mm). For the installation position of the receptacle see “Installation dimensions”. Grounding instruction This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electric current. , WARNING: Improper connection of the equipment grounding conductor may result in electric shock. Have the appliance checked by a qualified electrician or service technician if you are in doubt as to whether the appliance has been properly grounded. 8 The shut-off valve for the water connection must not be behind the appliance. It is recommended to place the shut-off valve directly next to the appliance or in another easily accessible location. When installing the water connection, observe the permitted installation areas for the pipe. For the permitted installation areas and dimensions see “Installation dimensions”. Installation dimensions X Y 18“ 9“ (457 mm) (229 mm) 24“ 12“ (610 mm) (305 mm) 30“ 15“ (762 mm) (381 mm) IMPORTANT ! It is strongly recommended the top panel of the enclosure be of solid material at least 5/8" (16 mm) thickness. IMPORTANT ! The side walls of the enclosure must be perfectly straight. The furniture return area has to be at least 4" (100 mm) deep. Legend: A Area for installation of the water connection It is recommended the water-box be placed adjacent to the installation enclosure, so that it can be accessed for service without uninstalling the appliance. If this is not possible, place the recessed water box within the shaded area. B Area for installation of the power connection C Opening depth of enclosure, depending on kitchen design C = 24" (610 mm) minimum 9 Required accessories and tools Supplied accessories Installation instructions Operating instructions Installation kit Optional accessories Sealing Kit for Side-by-Side Installation BSEALKIT10 Tools Cordless screwdriver Torx bit T20 + magnetic holder For permanent connection of two individual appliances, e.g. Freezer next to Refrigerator. Freedom Heater Kit for Side-by-Side Installation XHEATKIT10 If the gap between the appliances is less than 6" (160 mm). Torx screwdriver T20 5/ 16" (8 mm) hex nut driver Panel unification part (Metal strip) FPCONNTS10 For connection of two door panels. Can be used for standard height door panels without further preliminary work. Other required accessories Ice maker installation kit 1/4" OD copper line For connecting appliances which require water, e.g. for an ice maker. Maximum outer diameter of the water pipe (without fittings): 13/32" (10 mm). Other Stepladder Dolly, hand truck Hammer drill for drilling holes in wall or floor Bits according suitable for material and in different sizes Wooden beam (cross section min. 3" x 4") as an alternative tip protection, length according to the width of the installation enclosure Wooden screws in different sizes Thin plywood sheet, particle board or cardboard to protect the floor from damage Suitable material for covering and protecting furniture (e.g. protective sheets) Adhesive tape Note: Before using, check whether the removed adhesive tape leaves adhesive residue on the work surfaces! Otherwise do not use on high-quality work surfaces. 10 Wood drills in different sizes Open end wrench 1/2" (SW 13 mm) Multigrip pliers Adjustable wrench Cutter with adjustable blade Metal tape measure, folding rule Square Level, length 2' (60 cm) and 4' (1,2 m) Installation instructions The following installation instructions describe the installation steps for various appliance types: 2. Removing the packaging , WARNING: Refrigerator units Freezer units Be careful, otherwise people who are helping may be injured or the appliance may be damaged! Freezer units with ice maker The appliance may tip over while it is being Freezer units with ice-water dispenser unpacked or if the doors are opened. The appliance is very heavy. Wine storage units Therefore the diagrams may be a general representation of your appliance. Particular reference is made to special installation steps for individual appliance types. 1. Checking the installation enclosure , CAUTION: Use the following check list for a safe and trouble free installation. 1. Note: Check appliance for damage in transit. Do not install the appliance if it is visibly damaged. If in doubt, contact your dealer. To avoid floor damage: 1. Remove the packaging carton and be careful not to damage the surface of appliance. 2. Place packaging cardboard or plywood under the appliance. 3. Remove accessories from the outside of the appliance. Check the floor. Save adhesive tape which was used to attach the supplied accessories to the appliance. It can be used subsequently for attaching an edge protection to the installation enclosure walls (see section on “A / 3. Attaching an edge protection”). See section on “Installation/Floor”. 2. Check the dimensions of the installation enclosure, see “Installation dimensions”. 3. Check that the installation enclosure is square. 4. Check location of the socket. 4. Remove transportation protection devices (a) and lift appliance off the pallet – appliance is very heavy! 5. Carefully open the appliance – risk of tipping over – and remove accessories and installation materials from inside the appliance. Close the door again. See section on “Connecting the power” and in the section on “Installation dimensions”. 5. Check location of the water connection (only for appliances with ice maker). See section on “Connecting the water” and in the section on “Installation dimensions”. 6. Check attachment of the adjacent cabinet/fixtures. All cabinet parts in the vicinity of the appliance must be connected securely to the wall. 7. Check that adjacent cabinet/fixtures have adequate clearance (door opening angle). Note: Do not remove transportation safety devices which protect the shelves and storage compartments inside the appliance until the installation is complete, otherwise the parts may be damaged. 11 3. Transport of the appliance 4. Installation preparation , WARNING: Unpack installation materials and accessories. Be careful, otherwise people who are helping may be injured or the appliance may be damaged. To simplify installation, the packages are identified with labels A, B and C corresponding with the manual sections. The appliance is very heavy. The appliance is 83 1/8" (2126 mm) tall. If the appliance cannot be transported in an upright position, the appliance can be transported horizontally. Note: Do not raise up the appliance via the side panels. Risk of damage to the appliance! When raising up the appliance, observe the required minimum height at the installation location according to the following table: Raise up via appliance rear Do not raise up from appliance side 5. Special installation This symbol indicates that additional steps need to be taken before proceeding to the next chapter. Minimum height 86"/2185 mm Do not raise up the appliance via the side panels! Special installation steps are described after section C. Change over door hinge, see “Changing over the door hinges”. Sealing mat, see “Removing/ Note: Always use the appliance dolly from the rear side of the appliance. Never push it in from the front under the appliance. Risk of damage to the appliance! changing over the sealing mat” Side-by-Side installation, see “Side- by-Side installation”. Connecting the water, see “Preparing to connect the water” an “Connecting the water to the appliance”. Ice-water dispenser, see “Aligning the ice-water dispenser“. Cover strips for a wine unit, see “Attaching the cover strips” Door limitation pin, see “Adjusting the door opening angle”. 1. Transport the appliance to a suitable installation location with suitable means of transportation (trolley, lifting truck or hand). 2. Secure the appliance during transportation to prevent it from tipping. 12 1. Attaching the anti-tip-brackets , WARNING: Risk of injury and damage! Assure that there are no electrical wires or plumbing in the area which the screws could penetrate. , CAUTION: Risk of injury! Always wear safety glasses and other necessary protective devices or apparel when installing or working with dowels. Note: 2 anti-tip-brackets are required for each appliance. The supplied set contains fastening screws for various applications. Select the fastening screws according to the local conditions. The anti-tip-brackets (a) must overlap a minimum of 21/8” (54 mm) over the appliance to secure the appliance. If this minimum length cannot be observed for structural conditions it is possible to do this by fastening a spacer (b) behind the anti-tip angle, e.g. a sufficiently dimensioned wood board. Important notes for fastening with dowels and screws: The length of the plank should correspond to the width of the installation enclosure! Not recommended for use in light-weight masonry material such as cinder block. 1. Specify the attachment points of the anti-tip-brackets according to the section on “Installation dimensions”. Not recommended for use in new concrete which has not had time to cure. 2. Attach the anti-tip-brackets completely. Be sure screws hold tight. 13 2. Attaching an alternative anti-tip device Important note: If the anti-tip brackets cannot be attached securely, an alternative anti-tip-device can be attached. However, ensure that there is no play between the appliance and the anti-tip-device. If possible, always screw the wooden beam to existing studs on the rear panel of the installation enclosure. 1. Saw the wooden beam (cross section min. 3" x 4") to the required length. Length is equal to the width of the installation enclosure! 3. Attaching an edge protection To protect the edges of the installation enclosure, it is recommended to attach edge protection made of a suitable material. Note: If the installation enclosure is deeper than the appliance, select a beam which has a larger cross section or attach 2 beams. The beam must cover the appliance by at least 2" (50.8 mm). 4. Attaching the fastening sheets (lateral) Attach the fastening sheets (lateral) to the appliance. 2. 3. 4. 5. 6. 14 Mark the installation height (lower edge of the beam) on the rear panel of the installation enclosure. Select screws according to the thickness of the wooden beam: length = min. 2.5 x beam thickness, diameter #12 or #14. Note: Choose the number of screws according to the installation enclosure width, thereby ensuring that the beam can be attached securely. Depending to the subsurface: Locate wall studs in the rear of the installation enclosure and accordingly transfer their location to the wooden beam or fasten suitable dowel into the rear wall. Predrill the wooden beam. Attach the wooden beam to the rear panel of the installation enclosure. These are special installation steps. Instructions are provided after section C. Change over door hinge, see “Changing over the door hinges”. Sealing mat, see “Removing/ changing over the sealing mat” Side-by-Side installation, see “Side- by-Side installation”. Connecting the water, see “Preparing to connect the water”. 5. Pushing the appliance into the installation enclosure , CAUTION: 5. Caution when pushing the appliance into the installation enclosure. Do not damage the water line or power cord. To prevent the power cord from becoming caught, tie a piece of string to the middle of the power cord and feed forwards over the top of the appliance. When pushing in the appliance, pull the cable upwards. Take care not to pinch the power cord. Note: or When the floor or the appliance is not leveled in comparison to the installation enclosure adjust height adjustable wheels before you move the appliance into the installation enclosure. Using adhesive tape, tape the power cord to the floor centrally behind the appliance approx. 15" (380 mm) away from the rear panel of the installation enclosure. 1. Remove the base panel. 6. 2. Raise the height-adjustable wheels at the back by approx. 3/8" (10 mm). Carefully push the appliance into the installation enclosure. 7. Remove edge protection (if attached). 3. Put the electric plug into the socket. 4. Push the water line into the guard tube (a) at the rear of the appliance. , WARNING: Be careful, otherwise people who are helping may be injured or the appliance may be damaged. The appliance may tip over while the water line is pushing into the guard tube. 15 1. Aligning the appliance in the installation enclosure The height adjustment gauge (b) is used to set this height correctly. The upper edge of the gauge must be in alignment with the mark on the appliance. Note: To ensure that the appliance functions correctly, it must be set perfectly levelled. Do not twist or jam the appliance inside the installation enclosure! When adjusting the heightadjustable feet, proceed gradually: Always alternate between left and right, etc. For easier adjustment of the rear feet take the weight off by slightly tilting the appliance forward. Do not bend the appliance against the anti-tipbrackets. 2. Unscrew the feet at the front of the appliance until the mark (a) on the appliance is in alignment with the upper edge of the height adjustment gauge (b). 3. Align the appliance vertically using the feet at the back. Use a level! The positioning aid on the door have been designed for the following total thickness of door panels: 3 11/2" (38 mm) /4" (19 mm) Always take account of the possible differing thickness of the panel fronts which are to be fitted subsequently. 1. Align the appliance with the cabinet fronts using the positioning aid. Place level over the positioning aid on the door. 2. The height-adjustable feet at the front and rear can all be adjusted from the front. Front: with open-ended wrench 1/2" (Width across flats 13 mm) Rear: with 5/16" (8 mm) hex nut driver via flexible shaft. The mark (a) attached at the appliance base is used as a standard gage for height adjustment. When adjusting the height, align this mark at a height of 11/2" (32 mm) above the floor. It is very important to comply with this dimension for the subsequent alignment of the furniture fronts. 16 Attaching the appliance to the installation enclosure It is essential to attach the appliance to the top of the installation enclosure. 1. Screw the attachment plate lugs (top) to the overhead furniture. 2. If there is a fairly large gap above the appliance, fit a wooden beam above the appliance, ensuring that the wooden beam fits the gap exactly. 3. 4. If there enough room on the top of the appliance fix the attachment plate side lugs (top) to the side of the enclosure. 5. Shorten the fitting strip (a) to the required height to fill the gap. 6. Press fitting strip (a) into the cover strip. 7. Attach the cover strip (b) to the attachment plate (top). Screw on the bars of the fastening sheets (lateral) with the cabinet parts located next to them. Note: In the case of a Side-by-Side installation this installation step is not possible. These parts have been removed. Note: In the case of a side-by-side installation connect both cover rails to the bolt included in the installation accessories for side-by-side installation. These are special installation steps. Instructions are provided after section C. Connecting the water, see “Connecting the water to the appliance”. 17 1. Attaching the toe kick panel Note: Risk of damage to the appliance. Do not cover ventilation slots in the base panel. Wooden panel 1. If required, shorten wooden panel to the required length. 2. Screw wooden panel to the base panel from behind. There are already screw holes in the base panel. Nominal dimensions to be observed: 2. Aligning the base panel 1. Put on the base panel (do not screw on) and measure the difference in depth A between the base panel and toe kick panel of the adjacent cabinet. 2. Remove the base panel. 3. Adjust the brackets (a) to the dimensions A and tighten. 4. Attach the base panel. Stainless steel panel (accessory) 1. Attach the base panel to the appliance (do not screw on). 2. Remove the protective film from the adhesive pads. 3. Fit the toe kick panel to the base panel and press firmly into place. 18 3. Switching the appliance ON To guarantee the accuracy of the following working steps and thus the appearance of the overall kitchen front later on, the appliance should now be operated. 1. Open the appliance door. 2. Press the POWER button. 3. Press the POWER button again to shut off. Only for appliances with a water connection: In order to avoid the risk of damage caused by leaking water from damage possibly caused to the water pipe feeding the appliance, keep the shut-off valve closed. 4. 5. Loading the appliance door When attaching the door panels, it is recommended to load the door storage compartments in the appliance with weights in order to ensure that the gap width is as precise as possible. Recommendations: 18" Appliance: 22 lbs/10 kg 24" Appliance: 33 lbs/15 kg 30" Appliance: 44 lbs/20 kg Preparing the door panels Important note: When performing any work on the door panels, always observe the following: Always screw into the best load-bearing material of the door panel. Never screw into fillers, decorative strips or similar. Select a screw length which is always shorter than the thickness of the door panel. To prevent damage, protect surfaces of the door panels during installation. 6. The total weight of the door panel must not exceed the following values: 18" Appliance 44 Ibs/20 kg (19 lbs/8.5 kg *) 24" Appliance 55 Ibs/25 kg (32 lbs/14.5 kg *) 30" Appliance 64 Ibs/29 kg Removing the installation support part Unscrew the positioning aid from the appliance door. Note: Store the positioning aids, there will be used in an installation step later. (* Wine unit) In the case of 30" and 36" wide appliances 2 adjacent door panels can be attached instead of one large door. These door panels must be connected to a metal strip on the rear. This metal strip can be purchased from customer service as an optional accessory, see the section on “Required accessories and tools/Optional accessories”. Note: The instructions for carrying out this work step can be found in the separate installation instructions for this accessory. 19 7. 1. Attaching the adjusting rail to the door panel Measure the distance A between the adjusting rail and the overhead cabinet/fixtures. Notes: Attach the adjusting rail to the door panel with at least 10 screws. One screw should be inserted under each double threaded bolt. The adjusting rail features a variety of holes for the many different design options of door panels. Always screw into the best load-bearing material of the door panel. 8. Attaching the fixation strips to the door panel Note: The fixation strips are pre-assembled for stainless steel doors. In this case continue with the next installation step (“C / 9. Attaching the door panel”). 2. Loosen the 2 nuts (a) and remove the adjusting rail (b). 3. Mark this amount A on the rear of the door panel. 4. Determine and mark the centerline of the door panel. 5. Put on the adjusting rail and align along the marks. Mark the drill holes. 6. Drill the holes. 7. Screw on the adjusting rail tightly. 20 1. Hang the door panel on the double threaded bolt (a). 2. Align the door panel with the double threaded bolts (Torx screwdriver). Re-examine the dimensions of the gap continuously. Use the height adjustment gauge (b). 3. Transfer the middle drill holes along the outer edge of the appliance door to the door panel and mark. 4. Remove the door panel. 5. Using the positioning aid, mark the vertical sides of the door panel parallel. 9. Attaching the door panel Note: Now attach the furniture handles which are screwed from behind! 6. Using a square, extend the drill hole marks which you have just made to the vertical marks. 7. Apply the fixation strip and mark out the holes. 8. Pre-drill the holes. 9. Screw on the fixation strips. 1. Remove the fixing brackets (a) from the appliance door. To do this, loosen the bracket screws (b) only. 2. Insert removed fixing brackets (a) into the adjusting rails (b) on the door panel. 3. Open the appliance door. 21 4. Hang the door panel with adjusting rail over the double threaded bolts (1.). 5. Lower door panel and push the fixing brackets down over the fastening screws (2.). 10. Screw nuts onto the double threaded bolts and tighten. This will fix the side alignment of the door. 10. Attaching the lower bracket The lower bracket fixes the side position of the door. The number of lower brackets depends on the width and the design of the door panel. Screw on the lower brackets (Installation kit). Predrill holes in the door panel! 6. Adjust the door panel using the double threaded bolts (Torx screwdriver). Re-examine the dimensions of the gap continuously. 7. Close the door and check that the depth of the door panel is aligned with the adjacent fronts. If required, correct. 8. Tighten the bracket screws to fix the depth alignment. 9. Close the door and check the side alignment. Correct by gently tapping the edge of the open door panel with your hand. 22 1. Loosen the screw. 2. Push the bracket over the screw. 3. Check the side position of the door. 4. Screw in the screw. 5. Tighten the screw. 6. Put the cover on the brackets. 11. Attaching the strips 12. Adjusting the door spring 1. Rotate the adjusting screw with a cross-head screwdriver. Attach the cover strip (a) on the door. I = maximum spring tension 0 = no spring tension 2. Attach the light switch cover. The cover can be screwed to the door. These are special installation steps. Instructions are provided after section C. Ice-water dispenser, see “Aligning the ice-water dispenser“. Cover strips for a wine unit, see “Attaching the cover strips” Side-by-Side installation only: Door limitation pin, see “Adjusting the door opening angle”. Installation of the appliance is now complete. Insert the cover strip into the space between the appliances. The cover rail is included in the installation accessories for side-by-side installation. 23 Special installation Changing over the door hinges , 3. Unscrew (1.) and remove (2.) the door. 4. Remove the hinges. 5. Remove the ventilation grille. WARNING: Risk of injury! Before working on the hinge, release the spring. Note: The door hinges cannot be exchanged in the case of freezers with ice and water dispensers. Switching the door hinge is made easier if the appliance is stored here on the back (put the pallet underneath). 1. 2. 24 Release the spring on the hinge. Loosen the screw from I to 0. Remove the hinge box covers. 6. Mount new the ventilation grill. 7. Change over the hinge angle. 8. Attach the ventilation grille. 9. Change over the screw for the lower bracket. A replacement part for the ventilation grille to adapt to the modified door hinge is included in the installation materials and accessories. 25 10. Change over the fixation parts on the door. 13. Span the spring on the hinge. Tighten the screw from 0 to I. 14. Fix the hinge box cover. 11. Fix the hinges on the appliance. Change the hinges crosswise! 12. Fix the door. 26 Removing/changing over the sealing mat Freezers are factory equipped with a sealing mat for the Side-by-side installation. Side-by-Side installation If a Side-by-Side installation is intended, now connect the two appliances together. 1. Unpack the Side-by-Side kit and check that no parts are missing. 2. Place the appliances next to each other in the intended configuration. If the installation is planned as a individual unit, the sealing mat is not needed and can be removed. For the Side-by-Side installation the sealing mat is absolutely necessary. If the door hinge of the freezer to the other side has been placed before, the sealing mat must also be implemented to the opposite side. 27 3. Unscrew the base panels. Note: Freezers are factory equipped with a sealing mat for the Side-by-side installation. Continues the work to step 6. Attach the mat always left standing appliance! 4. Stick sealing mat from the Side-by-Side kit around the edge. Secure the sealing mat with the pins. 28 5. Place the water-absorbing stripes from the Side-bySide kit on the side wall and secure with self adhesive tape. 6. Screw side plates from the Side-by-Side kit to both appliances. Note the position of both appliances! 7. Screw the hinge halves in the Side-by-Side kit to both appliances. 10. Push the appliances together at the front as far as possible. 11. Loosen the screws on the top of the appliance and screw the installation aids to the upper side of both appliances. 8. Push the appliances together until the hinge halves interlock. 9. Insert pins into the hinges. 12. Pull the appliances together at the top with Water pump pliers (A). 13. When the appliances have been completely pulled together, insert the bar into the upper plates. 29 14. Pull the appliances together at the bottom with Water pump pliers. Preparing to connect the water 15. When the appliances have been completely pulled together, insert the bar into the lower plates. Use a tool to push the bar in all the way. (only for appliances which require a water connection) Note: Turn off the main water tap to prevent damage caused by leaking water. 1. Attach the water line to the shut-off valve according to the instructions supplied by the manufacturer of the ice maker installation kit. 2. Install the water line. Always observe the indicated dimensions to prevent damage to the water line when pushing in the appliance. 16. Remove the installation aids. To attach the cover strip to the attachment plate (top): 17. Connect both cover rails to the bolt included in the Side-by-Side kit. 30 Connecting the water to the appliance Aligning the ice-water dispenser Note: (for freezer unit with ice-water dispenser only) When bending the water line, do not kink it, otherwise there is a risk of leaks and water damage. Note: 1. Remove the cap from the appliance connection (1.). 2. Bend the water line according to the location of the connection on the appliance (2.). 3. Push the union nut and seal onto the water line. 4. Push the end of the water line into the appliance connection and screw on the union nut (3.). Tighten hand-tight. 5. 6. Using the open-ended wrench, tighten the union nut. Do not overturn! In the case of appliances with a high-grade steel door, there is a special covering frame. The ice-water dispenser can be aligned inside the cutout of the door panel. This allows the dispenser to be aligned parallel to the door panel in order to obtain an optimum overall appearance. Note: We suggest to attach the frame before adjusting the dispenser unit! 1. Slide cover frame onto the ice-water dispenser and press in until the frame is flush with the door surface. 2. Loosen screws on the 4 clamps (1.). 3. Insert flat screwdriver into one of the 4 slots and push the blocks sideways until the ice-water dispenser has the same distance from the door panel (2.). 4. Retighten the screws on the clamps (3.). Push back the water line into the guard tube as far as possible (4.). 7. Open the shut-off valve and main water tap. 8. Check the connection on the shut-off valve and on the appliance for leaks. 9. Close the shut-off valve. 31 5. Insert covers. 6. Insert the water collecting tray. Attaching the cover strips (for wine storage cupboard only) 1. 32 If the frame width is narrow, the cover strip side piece may have to be shortened. To determine the required length of the side piece, test pieces are enclosed with the cover strip. 2. Push cover strips on the longitudinal side into the gap between the door panel (a) and glass pane (b). 3. Cut the cover strips on the short sides to the required length. 4. Slide cover strips in the gap between the door panel (a) and glass pane (b). Adjusting the door opening angle Depending on the installation situation, it may be necessary to adjust the door opening angle. A door opening angle of 115° has been set at the factory. To adjust the door opening angle to 90°: 1. Open door to 90°. 2. Insert the banking pin through the boreholes which are now vertically aligned and drive in with a hammer. 33 1. 2. Fixation d'un dispositif anti-renversement alternatif ............... 44 3. 4. 5. Installation ............................................................ 37 1. 2. 1. 2. Sol ................................................................................ 37 3. 4. 5. 6. 7. 8. Accessoires fournis ................................................... 40 9. Local d'installation ..................................................... 37 Installation stable ....................................................... 37 54 1. 2. 3. 4. 5. 34 – Definitions , , 35 Appareil individuel Côte à côte 36 Installation , AVERTISSEMENT: Remarque: en plein air, Ibs/140 Ibs/158 Ibs/115 Ibs/135 Ibs/150 Ibs/135 Ibs/160 kg kg kg* kg* kg* kg kg Sol , 37 , 38 AVERTISSEMENT: Dimensions d'installation X Y 18“ 9“ (457 mm) (229 mm) 24“ 12“ (610 mm) (305 mm) 30“ 15“ (762 mm) (381 mm) B C 39 Instructions d'installation Kit d'installation Tournevis Torx T20 Pince multiprises 40 1. , 1. 2. , ATTENTION: 1. 2. 3. 4. 2. 3. 4. 5. 6. 7. 41 5. 1. 2. 3. , AVERTISSEMENT: 4. 42 1. , , Remarque: 2. 2. Fixation d'un dispositif anti-renversement alternatif 43 1. 3. Remarque: 2" (50,8 mm). 4. 2. 3. 4. 6. 44 5. , ATTENTION: 5. Remarque: Ou bien 1. 2. 3. 4. , 6. 7. 45 1. 3. 2. 46 3. 5. 6. 7. Remarque: 4. 47 1. 2. 2. 1. 2. 3. 4. 2. 3. 48 3. 5. 1. 2. 3. Appareil de 18" : 22 lbs/10 kg Appareil de 24" : 33 lbs/15 kg Appareil de 30" : 44 lbs/20 kg 4. Appareil de 18" : 44 Ibs/20 kg (19 lbs/8,5 kg *) Appareil de 24" : 55 Ibs/25 kg (32 lbs/14,5 kg *) Appareil de 30" : 64 Ibs/29 kg 6. 49 7. 1. Remarque: 8. 2. 3. 4. 5. 6. 7. 50 1. 2. 3. 4. 5. 6. 7. 8. 9. 9. 2. 51 3. 4. 5. 6. 7. 8. 9. 52 1. Desserrez la vis. 2. 3. 4. 5. 6. 1. 2. 53 2. 3. 4. Remarque: 1. 54 5. 6. 7. 8. 9. 55 56 2. 57 3. Remarque: 4. 58 5. 6. 7. 8. 9. 59 60 1. 2. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 7. 8. 9. 61 5. 6. 62 1. 2. 3. 4. 1. 2. 63 Índice INSTRUCCIONES IMPORTANTES DE SEGURIDAD ................................................... 65 1. 2. Montaje de un dispositivo antivuelco adicional ............................................... 73 3. 4. 5. 1. 2. 1. 2. 3. Base ............................................................................. 67 4. 5. 6. 7. 8. 9. 84 Cambiando las bisagras ........................... 84 1. 2. Desembalaje ........................................ 71 3. 4. 5. 64 , , NOTA ADVERTENCIA: 65 66 ADVERTENCIA: Nota: – Base , 67 , ADVERTENCIA: , Refrigerador 24" 2.0 Amper Refrigerador 30" 2.0 Amper 3.5 Amper 4.0 Amper 4.5 Amper 2.0 Amper 2.0 Amper 68 X Y 18“ 9“ (457 mm) (229 mm) 24“ 12“ (610 mm) (305 mm) 30“ 15“ (762 mm) (381 mm) Leyenda: A B C 69 – – Bit tipo Torx T20 y T30 + un soporte magnético Brocas para madera de diversas medidas Llave de boca 1/2" (13 mm) Pinza universal Llave ajustable Otros 70 Nota: 1. 2. 3. 4. 5. 1. , 1. 2. 3. 4. 5. 6. 7. 2. Desembalaje , ADVERTENCIA: pesado. 71 3. 4. , ADVERTENCIA: 5. 2. 72 1. , , Nota: 2. 2. 73 1. 3. 4. 2. 3. 4. 5. 6. 74 5. , ATENCIÓN: 5. 1. Quitar el panel base. 2. 6. 3. 7. 4. , 75 1. Nota: 3. 2. 3 11/2" (38 mm) /4" (19 mm) 1/ " 2 76 2. 3. 5. 6. 7. Nota: 4. 77 1. 2. 2. 1. 2. Quite el panel base. 3. 4. Monte el panel base. Panel de acero inoxidable (accesorio) 1. 2. 3. 78 3. 5. 1. 22 lbs/10 kg 2. 33 lbs/15 kg 3. 44 lbs/20 kg 4. 44 Ibs/20 kg (19 lbs/8,5 kg *) 55 Ibs/25 kg (32 lbs/14,5 kg *) 64 Ibs/29 kg 6. 79 7. 1. Nota: 8. 2. 3. 4. 5. 6. 7. 80 1. 2. 3. 4. 5. 6. 7. 8. 9. 9. 2. 3. 81 4. 5. 6. 7. 8. 9. 82 1. 2. 3. 4. 5. 6. 1. 2. 83 3. 4. Quite las bisagras. 5. Nota: 1. 2. 84 6. 7. 8. 9. 85 86 2. 87 3. Nota: 4. 88 5. 6. 7. 8. 9. 89 2. 90 1. 2. 3. 4. 5. 6. 7. 8. 9. 2. 3. 4. 5. 6. 91 3. 4. 2. 92 2. 93
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement