Craftsman 316.292711 User manual

Operator’s Manual
4-Cycle
with
• SAFETY
• ASSEMBLY
• OPERATION
• MAINTENANCE
• PARTS LIST
• ESPAÑOL, p. 23
CAUTION: Before using
this product, read this
manual and follow all
safety rules and operating
instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.
Visit our website: www.sears.com/craftsman
P/N 769-02846
(1/07)
INTRODUCTION
Maintenance and Repair Instructions . . . . . . . . . . .12
TABLE OF CONTENTS
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2
Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3
Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7
Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . .8
Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . .18
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Notes (Intentionally Blank) . . . . . . . . . . . . . . . . . . .21
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . E21-E23
Repair Protection Agreement . . . . Inside Back Cover
Service Numbers . . . . . . . . . . . . . . . . . . .Back Cover
Starting/Stopping Instructions . . . . . . . . . . . . . . . .10
Operating Instructions . . . . . . . . . . . . . . . . . . . . . .11
WARRANTY
Full Two-Year Warranty on Craftsman Cultivator / Edger
For two (2) years from the date of purchase, if this Craftsman Equipment is maintained, lubricated, and tuned up
according to the instructions in the operator’s manual, Sears will repair or replace free of charge any parts found to be
defective in material or workmanship. Warranty service is available free of charge by returning Craftsman equipment to
your nearest Sears Service Center. In-home warranty service is available but a trip charge will apply. This Warranty
applies only while this product is in the United States.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as spark plugs, air cleaners, belts, and oil filters.
• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.
• Repairs necessary because of operator abuse, including but not limited to, damage caused by objects, such as stones
or metal debris, oversized stock, impacting objects that bend the frame or crankshaft, or over-speeding the engine.
• Repairs necessary because of operator negligence, including but not limited to, electrical and mechanical damage
caused by improper storage, failure to use the proper grade and amount of engine oil, or failure to maintain the
equipment according to the instructions contained in the operator’s manual.
• Engine (fuel system) cleaning or repairs caused by fuel determined to be contaminated or oxidized (stale). In general,
fuel should be used within 30 days of its purchase date.
• Equipment used for commercial or rental purposes.
TO LOCATE THE NEAREST SEARS SERVICE CENTER OR TO SCHEDULE SERVICE, SIMPLY CONTACT SEARS AT
1–800-4-MY-HOME®.
This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
CALIFORNIA PROPOSITION 65 WARNING
WARNING
THE ENGINE EXHAUST FROM THIS
PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
2
SPARK ARRESTOR NOTE
NOTE: For users on U.S. Forest Land and in the
states of California, Maine, Oregon and Washington.
All U.S. Forest Land and the state of California (Public
Resources Codes 4442 and 4443), Oregon and
Washington require, by law that certain internal
combustion engines operated on forest brush and/or
grass-covered areas be equipped with a spark arrestor,
maintained in effective working order, or the engine be
constructed, equipped and maintained for the prevention
of fire. Check with your state or local authorities for
regulations pertaining to these requirements. Failure to
follow these requirements could subject you to liability or
a fine. This unit is factory equipped with a spark
arrestor. If it requires replacement, ask your LOCAL
SERVICE DEALER to install the Accessory Part
#180890 Spark Arrestor Kit.
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
SYMBOL
MEANING
Indicates
danger,
warning or caution. Attention is required in
order to avoid serious personal injury. May
be used in conjunction with other symbols
or pictographs.
SAFETY ALERT:
NOTE: Advises you of information or instructions vital to
the operation or maintenance of the equipment.
Read the Operator’s Manual(s) and follow all
warnings and safety instructions.
Failure to do so can result in serious injury to the
operator and/or bystanders.
SYMBOL
MEANING
Failure to obey a
safety warning will
result in serious injury to yourself or to
others. Always follow the safety precautions
to reduce the risk of fire, electric shock and
personal injury.
DANGER:
Failure to obey a
safety warning can
result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock and
personal injury.
WARNING:
to obey a
CAUTION: Failure
safety warning may
result in property damage or personal injury
to yourself or to others. Always follow the
safety precautions to reduce the risk of fire,
electric shock and personal injury.
• IMPORTANT SAFETY INSTRUCTIONS •
READ ALL INSTRUCTIONS BEFORE
OPERATING
• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
• Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
• Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
• All guards and safety attachments must be installed
properly before operating the unit.
• Inspect the unit before use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in
place and secure. Replace parts that are cracked,
chipped, or damaged in any way. Do not operate the
unit with loose or damaged parts.
• Carefully inspect the area before starting the unit.
Remove all debris and hard or sharp objects such as
glass, wire, etc.
• Be aware of the risk of injury to the head, hands and
feet.
• Clear the area of children, bystanders, and pets. At a
minimum, keep all children, bystanders, and pets
outside a 50 feet (15 m) radius; there still may be a risk to
bystanders from thrown objects. Bystanders should be
encouraged to wear eye protection. If you are
approached, stop the unit immediately.
• Squeeze the throttle control and check that it returns
auto-matically to the idle position. Make all
adjustments or repairs before using unit.
SAFETY WARNINGS FOR GAS UNITS
• Store fuel only in containers specifically designed and
approved for the storage of such materials.
Gasoline is highly
flammable, and its
vapors can explode if ignited. Take the
following precautions:
WARNING:
• Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
• Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the cap of the fuel
tank, or add fuel, when the engine is hot. Never
operate the unit without the fuel cap securely in place.
Loosen the fuel tank cap slowly to relieve any pressure
in the tank.
• Add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. Slowly remove the fuel
cap only after stopping engine. Do not smoke while
fueling or mixing fuel. Wipe up any spilled fuel from the
unit immediately. Always wipe unit dry before using.
• Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke or allow sparks and open flames near the area
while adding fuel or operating the unit.
3
RULES FOR SAFE OPERATION
WHILE OPERATING
• Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can kill. Operate
this unit only in a well ventilated outdoor area.
• Wear safety glasses or goggles that meet ANSI Z87.1
standards and are marked as such. Wear ear/hearing
protection when operating this unit. Wear a face or dust
mask if the operation is dusty.
• Wear heavy, long pants, boots, gloves and a longsleeved shirt. Do not wear loose clothing, jewelry, short
pants, sandals or go barefoot. Secure hair above
shoulder level.
• This unit has a clutch. The tines remain stationary
when the engine is idling. If they do not, have the unit
adjusted by an authorized service technician.
• Be sure the tines are not in contact with anything
before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and unit
must be in a stable position while starting. See
Starting/Stopping Instructions.
• Use the right tool. Only use this tool for the purpose
intended.
• Use extreme caution when reversing or pulling the unit
towards you.
• Do not overreach. Always keep proper footing and
balance. Take extra care when working on steep
slopes or inclines.
• Always hold the unit with both hands when operating.
Keep a firm grip on the grips.
• Keep hands, face, and feet at a distance from all moving
parts. Do not touch or try to stop the tines when they are
rotating.
• Do not touch the engine or muffler. These parts get
extremely hot from operation, even after the unit is turned
off.
• Do not operate the engine faster than the speed
needed to cultivate. Do not run the engine at high
speed when you are not cultivating.
• Always stop the engine when cultivating is delayed or
when walking from one cultivating location to another.
• If you strike or become entangled with a foreign object,
stop the engine immediately and check for damage. Do
not operate before repairing damage. Do not operate the
unit with loose or damaged parts.
• Stop the unit, switch the engine to off, and disconnect
the spark plug for maintenance or repair.
• Use only original equipment manufacturer
replacement parts and accessories for this unit. These
are available from your authorized service dealer. Use
of any unauthorized parts or accessories could lead to
serious injury to the user, or damage to the unit, and
void your warranty.
• Keep unit clean of vegetation and other materials.
They may become lodged between the tines and
guard.
• To reduce fire hazard, replace faulty muffler and spark
arrestor, keep the engine and muffler free from grass,
leaves, excessive grease or carbon build up.
AFTER USE
• Clean tines with a household cleaner to remove any
gum buildup. Oil the tines with machine oil to prevent
rust.
OTHER SAFETY WARNINGS
• Never store a fueled unit inside a building where fumes
may reach an open flame or spark.
• Allow the engine to cool before storing or transporting.
Be sure to secure the unit while transporting.
• Store the unit in a dry area, locked up or up high to
prevent unauthorized use or damage, out of the reach
of children.
• Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use, see Cleaning and Storage
instructions.
• Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
SAVE THESE INSTRUCTIONS
4
RULES FOR SAFE OPERATION
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL
MEANING
SYMBOL
MEANING
• THROWN OBJECTS AND
ROTATING CUTTER CAN CAUSE
SEVERE INJURY
• SAFETY ALERT SYMBOL
Indicates danger, warning, or
caution. May be used in conjunction
with other symbols or pictographs.
WARNING: Do not
operate without the proper guards in
place. Keep away from the rotating
tines.
• WARNING - READ OPERATOR'S
MANUAL
Read the Operator’s Manual(s) and
follow all warnings and safety
instructions. Failure to do so can
result in serious injury to the
operator and/or bystanders.
• ON/OFF STOP CONTROL
ON / START / RUN
• ON/OFF STOP CONTROL
OFF or STOP
• WEAR EYE AND HEARING
PROTECTION
WARNING: Thrown
objects and loud noise can cause
severe eye injury and hearing loss.
Wear eye protection meeting ANSI
Z87.1-1989 standards and ear
protection when operating this unit.
Use a full face shield when needed.
• KEEP BYSTANDERS AWAY
WARNING: Keep all
bystanders, especially children and
pets, at least 50 feet (15 m.) from the
operating area.
• UNLEADED FUEL
Always use clean, fresh unleaded fuel.
• CHOKE CONTROL
1
2
3
1 • FULL choke position.
2 • PARTIAL choke position.
3 • RUN position.
• HOT SURFACE WARNING
Do not touch a hot muffler or
cylinder. You may get burned. These
parts get extremely hot from
operation. When turned off they
remain hot for a short time.
• GARDEN CULTIVATORS –
ROTATING TINES CAN CAUSE
SEVERE INJURY
WARNING: Stop the
• OIL
Refer to operator's manual for the
proper type of oil.
engine and allow the tines to stop
before installing or removing tines,
or before cleaning or performing any
maintenance. Keep hands and feet
away from rotating tines.
5
ASSEMBLY INSTRUCTIONS
NOTE: Before setting up your cultivator / edger,
disconnect the spark plug wire from the spark
plug.
ADJUSTING TINE DEPTH
POSITIONING THE HANDLEBARS
To adjust the wheel support bracket proceed as follows:
1. Stop engine and disconnect spark plug to avoid
accidental starting.
1. Loosen the two knobs on the inside of the
handlebars (Fig. 1).
2. Remove cotter pin from the clevis pin and slide clevis
pin out of tailpiece bracket (Fig. 3).
2. With the unit upright, swing the handlebars up into
the operating position (Fig. 1).
3. Slide the wheel support bracket up or down in the
tailpiece, aligning the holes to the desire height.
NOTE: Take care not to pinch the throttle cable or
switch wires when positioning the handlebar.
4. Place the clevis pin through the hole and secure with
cotter pin.
3. Tighten the knobs to secure the handlebars in place.
Clevis Pin
NOTE: Do not over-tighten the knobs.
4. Reconnect the spark plug wire to the spark plug.
Cotter Pin
Wheel
Support
Bracket
Tailpiece Bracket
Fig. 3
ATTACHING THE EDGER WHEEL AND
BLADE
To convert the cultivator to an edger proceed as follows:
1. Push the On/Off switch to Off (O) position to stop
engine and tines and disconnect spark plug to avoid
accidental starting.
NOTE: It may be necessary to lay the cultivator / edger
back in a horizontal position on a flat level surface
with the upper handle touching the ground.
Fig. 1
Handlebars
Bolt
Handlebar
Knob
2. Remove the click pin from each end of the tine shaft
and slide the tines off the shaft.
3. Slide the edger wheel, with the hub facing inward,
onto the right side of the tine shaft and secure with
the click pin in the inside hole (Fig. 4).
4. Slide the edger blade with the hub facing out onto
the left side of tine shaft and secure with the click pin
in the inside hole (Fig. 4).
5. The edger guide line indicates where cutting will
occur. Guide the unit along a flowerbed, sidewalk, or
driveway so the edger guide line is above the desired
line of cut.
Edger Guide
Line
Hole
Washer
Fig. 2
Hub
Edger Wheel
Click Pin
Tine Shaft
Edger Blade
Fig. 4
7
OIL AND FUEL INFORMATION
CAUTION:
OVERFILLING OIL
CRANKCASE MAY
CAUSE PRODUCT DAMAGE. Check and
maintain the proper oil level in the crank
case; it is important and cannot be
overemphasized. Check the oil before each
use and change it as needed. See Changing
the Oil.
Funnel Spout
RECOMMENDED OIL TYPE
Using the proper type and weight of oil in
the crankcase is extremely important.
Check the oil before each use and change
the oil regularly. Using incorrect or dirty oil can cause
premature engine wear and failure.
Use a high-quality SAE 30 weight oil of API (American
Petroleum Institute) service class SF, SG, SH.
Fig. 5
Oil Fill
Plug/Dipstick
ADDING OIL TO CRANKCASE: INITIAL USE
NOTE: This unit is shipped without oil in the crankcase.
In order to avoid damage to the unit, put oil in
the crankcase before attempting to start unit.
Your unit is supplied with one 3.04 fluid oz. (90 ml.)
bottle of SAE 30 SF, SG, SH oil (Fig. 5).
NOTE: Save the bottle to measure the correct amount
for future oil changes. See Changing the Oil.
Fig. 6
NOTE: Your new 4-Cycle cultivator is shipped for
operation in conditions above 40°F (4°C). For
cold weather operation, where temperatures
fall below 40°F (4°C), use a high-quality SAE
10W30 weight oil of API (American Petroleum
Institute) service class SF, SG, SH.
O-Ring
Oil Fill Plug/Dipstick
1. Unscrew the oil bottle top and remove the paper seal
covering the opening. Replace the top and cut the
tip off the funnel spout (Fig. 5).
2. Place the unit on a flat level surface with the
cultivator in a horizontal position (Fig. 6).
3. Remove the oil plug / dipstick from the crankcase
(Fig. 7).
4. Pour the entire bottle of oil into the oil fill hole
(Fig. 8).
Oil Fill Hole
Fig. 7
NOTE: Never add oil to the fuel or fuel tank.
5. Wipe up any oil that may have spilled and reinstall
the oil fill plug / dipstick.
The importance of checking and maintaining the proper
oil level in the crankcase cannot be overemphasized.
Check oil before each use and change as specified in
the Maintenance Schedule.
Oil Fill
Fig. 8
8
OIL AND FUEL INFORMATION
RECOMMENDED FUEL TYPE
Old fuel is the primary reason for improper
unit performance. Be sure to use fresh,
clean, unleaded gasoline.
NOTE: This is a four cycle engine. In order to avoid
damage to the unit, do not mix oil with gasoline.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and
oxygenates such as ethanol, methanol or MTBE (ether).
Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel form acids when stored.
When using alcohol-blended fuel, use fresh fuel that is
less than 60 days old.
Using Blended Fuels
If you choose to use a blended fuel, or if its use is
unavoidable, follow recommended precautions:
• Always use fresh unleaded gasoline
• Use Craftsman Fuel Stabilizer or an equivalent
• Drain tank and run the engine dry before storing unit
Using Fuel Additives
The use of fuel additives, such as Craftsman Fuel
Stabilizer or an equivalent, will inhibit corrosion and
minimize the formation of gum deposits. Using a fuel
additive can keep fuel from forming harmful deposits in
the carburetor for up to six (6) months. Add 0.8 oz.
(23 ml.) of fuel additive per gallon of fuel to an approved
gas container according to the instructions on the
container. NEVER add fuel additives directly to the unit's
gas tank.
FUELING THE UNIT
NOTE: Fill or add fuel to the tank only when the
cultivator is in a horizontal position (Fig. 9).
1. Remove fuel cap. Remove the tag from the fuel tank
neck.
2. Place spout of gas container into the fill hole on the
fuel tank and fill tank.
NOTE: Do not overfill tank.
3. Wipe up any gasoline that may have spilled.
4. Reinstall the fuel cap.
5. Move the unit at least 30 ft. (9.1 m) from the fueling
source and site before starting the engine.
NOTE: Dispose of the old gasoline in accordance to
Federal, State and Local regulations.
Fig. 9
Gasoline is
extremely
flammable. Ignited Vapors may explode.
Always stop the engine and allow it to cool
before filling the fuel tank. Do not smoke
while filling the tank. Keep sparks and open
flames at a distance from the area.
WARNING:
Remove fuel cap
slowly to avoid injury
from fuel spray. Never operate the unit
without the fuel cap securely in place.
WARNING:
Add fuel in a clean,
well ventilated
outdoor area. Wipe up any spilled fuel
immediately. Avoid creating a source of
ignition for spilt fuel. Do not start the engine
until fuel vapors dissipate.
WARNING:
9
STARTING/STOPPING INSTRUCTIONS
ON (I)
Operate this unit only
in a well- ventilated
outdoor area. Carbon monoxide exhaust fumes
can be lethal in a confined area.
WARNING:
OFF (O)
WARNING:
Avoid accidental
starting. Make sure
you are in the starting position when pulling
the starter rope (Fig. 12). To avoid serious
injury, the operator and unit must be in a stable
position while starting.
Throttle
Control
STARTING INSTRUCTIONS
1. Check the oil level in the crankcase. Refer to
Checking the Oil Level.
2. Fill the fuel tank with fresh, clean unleaded gasoline.
Refer to Fueling the Unit.
3. Put the On/Off Stop Control in the ON [I] position
(Fig. 10).
4. Place the choke lever in Position 1 (Fig. 11).
5. Fully press and release the primer bulb 10 times,
slowly. Some amount of fuel should be visible in the
primer bulb and fuel lines (Fig. 11). If you can’t see
fuel in the bulb, press and release the bulb as many
times as it takes before you can see fuel in it.
6. Hold the throttle and handlebar with one hand and
grab the starter rope with your other hand. Use your
foot to hold down the cultivator (Fig. 12).
NOTE: Tilt the unit back slightly to bring the tines off the
ground when starting.
7. While squeezing the throttle control, pull the starter
rope with a smooth and steady pull. Repeat this 5
times.
NOTE: The unit uses the Incredi-Pull™ starting system ,
which significantly reduces the effort required to
start the engine. You must pull the starter rope out
far enough to hear the engine attempt to start.
There is no need to pull the rope briskly-- there is
no harsh resistance when pulling. Be aware that
this starting method is vastly different from (and
much easier than) what you may be used to.
8. Move the choke lever to Position 2.
9. While squeezing the throttle control, pull the starter
rope in the same manner as explained in Step 7. Pull
1 to 3 times to start the engine.
10. Keep the throttle squeezed and allow the engine to
warm up for 15 to 30 seconds.
11. Place the choke lever in Position 3. Release the
throttle control to the idle position and begin
operation.
IF... The engine does not start, repeat Steps 4 - 11.
IF... The engine fails to start after a few attempts, place
the choke lever in Position 3 and squeeze the
throttle control. Pull the starter rope 3 to 8 times.
The engine should start. If not, continue pulling
starter rope until the engine starts.
IF WARM... If the engine is already warm, make sure
the On/Off Stop control is in the ON position and
start the unit with the choke lever in Position 2. After
the unit starts, move the choke lever to Position 3.
10
Fig. 10
Choke Lever
Position 3
Position 2
Position 1
Primer Bulb
Fig. 11
Cultivator
Equipped With
Incredi-Pull
Starting
Fig. 12
STOPPING INSTRUCTIONS
1. Release your hand from the throttle control. Allow the
engine to cool down by idling.
2. Put the On/Off Stop Control in the OFF (O) position.
OPERATING INSTRUCTIONS
OPERATING TIPS
Dress properly to
reduce the risk of
injury when operating this unit. Do not
wear loose clothing or jewelry. Wear eye
and ear/hearing protection. Wear heavy
long pants, boots and gloves. Do not wear
short pants, sandals or operate barefoot.
WARNING:
1. Move the cultivator to the work area prior to starting
the engine. Transport the cultivator by pushing or
pulling it along on its wheels.
To prevent serious
personal injury,
never pick-up or carry the unit while the
engine is running.
WARNING:
2. Start the unit by following the Starting Instructions.
3. With the engine running and the tines off the ground,
depress the throttle control to increase the engine
speed.
4. While holding the upper handle with both hands,
slowly lower the cultivator until the tines make
contact with the ground (Fig. 13).
5. As cultivating action begins, tilt the cultivator up
slightly using the handle so that the tines can
penetrate the ground.
6. Once the ground has been broken, continue at a
moderate pace until you are familiar with the controls
and the handling of the cultivator.
7. If the tines are digging too deep or not deep enough,
adjust the wheel bracket as described in Adjusting
Tine Depth.
To prevent serious
personal injury, use
extreme caution when reversing
or pulling the unit towards you.
WARNING:
Fig. 13
TRANSPORTING THE UNIT
To prevent serious
personal injury,
always stop the engine when operation is
delayed or when transporting the unit from
one location to another
WARNING:
1. Stop the engine.
2. Tilt the unit back until the tines clear the ground.
3. Push or pull the unit to the next location to be
cultivated.
11
MAINTENANCE AND REPAIR INSTRUCTIONS
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should
also be a part of any seasonal tune-up.
NOTE: Maintenance, replacement, or repair of the
emission control devices and system may be
performed by a Sears or other qualified service
dealer. Call 1-800-4-MY-HOME® for more
information.
NOTE: Some maintenance procedures may require
special tools or skills. If you are unsure about
these procedures, take your unit to a Sears or
other qualified service dealer. Call 1-800-4-MYHOME® for more information.
To prevent serious
injury, never perform
maintenance or repairs with unit running.
Always service and repair a cool unit.
Disconnect the spark plug wire to ensure that
the unit cannot start.
WARNING:
FREQUENCY
MAINTENANCE REQUIRED
REFER TO
Before starting engine
Fill fuel tank with fresh fuel
Check oil
Page 9
Page 13
Every 10 hours
Clean and re-oil air filter
Page 14
First change at 10 hours
Every 25 hours thereafter
Every 25 hours
Change oil
Change oil
Clean spark arrestor
Page 13
Page 13
Page 15
Every 25 hours
Check spark plug condition and gap
Page 15
TINE REMOVAL AND REPLACEMENT
All 4 tines should be replaced at the same time because
they will wear evenly through normal use. Work on one
side at a time.
5. Place one “A” tine and one “B” tine onto the shaft.
6. Secure the new tines to the shaft with click pins. It
may be necessary to wash the dirt off the tines and
shaft for ease of removal.
To prevent serious
personal injury,
always wear heavy gloves when handling
the tines.
WARNING:
“A” Tine
1. Put the On/Off Stop Control in the STOP (O) position
and disconnect the spark plug wire.
NOTE: It may be necessary to lay the cultivator back in a
horizontal position on a flat level surface with the
upper handle touching the ground.
2. Remove the click pin from each end of the tine shaft.
Slide the tines off of the shaft (Fig. 14).
3. Clean and oil the shaft.
4. Slide on the new tines with the hubs facing out. The
four tines are marked with the letters “A” or “B.”
12
Click Pin
“B” Tine
Hubs
Fig. 14
MAINTENANCE AND REPAIR INSTRUCTIONS
CHECKING THE OIL LEVEL
To prevent extensive
engine wear and
damage to the unit, always maintain the
proper oil level in the crankcase. Never
operate the unit with the oil level below the
bottom of the dipstick.
CAUTION:
The importance of checking and maintaining the proper
oil level in the crankcase cannot be overemphasized.
Check oil before each use:
1. Stop the engine and allow oil to drain into the crankcase.
2. Place the unit on a flat, level surface to get a proper
oil level reading (Fig. 9).
3. Keep dirt, grass clippings and other debris out of the
engine. Clean the area around the oil fill plug/dipstick
before removing it.
4. Remove the oil fill plug/dipstick and wipe off oil.
Reinsert it all the way back in.
5. Remove the oil fill plug/dipstick and check the oil level.
Oil should be up to the top of the dipstick (Fig. 15).
CHANGING THE OIL
For a new engine, change the oil after the first 10 hours of
operation. Change the oil while the engine is still warm. The
oil will flow freely and carry away more impurities.
gloves to
CAUTION: Wear
prevent injury when
handling the unit.
1. Unplug spark plug wire to prevent accidental starting.
2. Remove the oil fill plug/dipstick.
3. Pour the oil out of the oil fill hole and into a container
by tipping the unit to a vertical position (Fig. 17).
Allow ample time for complete drainage.
Oil Fill Plug/Dipstick
O-Ring
Fig. 17
4. Wipe up any oil residue on the unit and clean up any
oil that may have spilled. Dispose of the oil
according to Federal, State and local regulations.
Full
Add 1.4-1.5 Oz.
(41-44 ml)
5. Refill the crankcase with 3.04 fluid ounce (90 ml) of
SAE 30 SF, SG, SH oil.
Top of Dipstick
Fig. 15
6. If the level is low, add a small amount of oil to the oil
fill hole and recheck (Fig. 16). Repeat this procedure
until the oil level reaches the top of the dipstick.
NOTE: Use the bottle and spout saved from initial use to
measure the correct amount of oil. Pour fresh
fuel into the bottle and fill it to the top of the
label. The top of the label on the bottle measures
approximately 3.04 ounces (90 ml). Check the level
with the dipstick. If the level is low, add a small
amount of oil and recheck. Do not overfill (Fig. 18).
NOTE: Do not overfill the unit.
O-Ring
Fill Level
Oil Fill Plug/Dipstick
Oil Fill Hole
Fig. 16
NOTE: Make sure the O-ring is in place on the oil fill
plug/dipstick when checking and changing the
oil (Fig. 16).
Fig. 18
6. Replace the oil fill plug/dipstick.
7. Reconnect the spark plug wire.
13
MAINTENANCE AND REPAIR INSTRUCTIONS
AIR FILTER MAINTENANCE
Cleaning the Air Filter
Clean and re-oil the air filter every 10 hours of operation.
It is an important item to maintain. Failure to maintain
your air filter properly can result in poor performance or
can cause permanent damage to your engine.
4. Apply enough clean SAE 30 motor oil to lightly coat
the filter (Fig. 21).
To avoid serious
personal injury,
always turn the unit off and allow it to cool
before you clean or service it.
WARNING:
1. Open the air filter cover. Push the tab on the left side
of the cover in, swing the air filter cover out and off
the air filter housing (Fig. 19).
2. Remove the air filter and the screen that sits
behind it (Fig. 19).
Screen
Air Filter
Fig. 21
5. Squeeze the filter to spread and remove excess oil
(Fig. 21).
6. Replace the filter (Fig. 19).
NOTE: If the unit is operated without the air filter, you
will VOID the warranty.
7. Reinstall the air filter cover. Position the hooks on
the right side of the air filter cover into the slots at
the right side of the air filter housing.
8. Swing the cover to the left until the tab on the air
filter cover snaps into place in the slot on the left
side of the air filter housing (Fig. 18).
CARBURETOR ADJUSTMENT
Tab
Choke Lever
The idle speed of the engine is adjustable. An idle
adjustment screw is reached though a hole in the top of
the engine cover (Fig. 22).
NOTE: Careless adjustments can seriously damage your
unit. For carburetor adjustments, take your unit
to a Sears or other qualified service dealer.
Air Filter Cover
Air Filter Housing
Hooks
Check Fuel
Old fuel is usually the reason for improper unit
performance. Drain and refill the tank with fresh fuel prior
to making any adjustments. Refer to Oil and Fuel
Information.
Slot
Air Filter
Tab
Fig. 19
3. Wash the filter in detergent and water (Fig. 20). Rinse
the filter thoroughly and allow it to dry.
Clean Air Filter
The condition of the air filter is important to the operation
of the unit. A dirty air filter will restrict air flow. This is
often mistaken for an out of adjustment carburetor.
Check the condition of the air filter before adjusting the
idle speed screw. Refer to Air Filter Maintenance.
Adjust Idle Speed Screw
This unit needs to
run during idle
speed adjustment. Wear protective clothing
and observe all safety instructions to
prevent serious personal injury.
WARNING:
Fig. 20
14
If, after checking the fuel and cleaning the air filter, the
engine still will not idle, adjust the idle speed screw as
follows:
1. Start the engine and let it run at a high idle for a minute
to warm up. Refer to Starting/Stopping Instructions.
MAINTENANCE AND REPAIR INSTRUCTIONS
NOTE: Ensure the tines are not in contact with the
ground when adjusting the idle.
2. Release the throttle trigger and let the engine idle. If the
engine stops, insert a small phillips or flat blade
screwdriver into the hole in the air filter/muffler cover
(Fig. 22). Turn the idle speed screw in, clockwise, 1/8 of
a turn at a time (as needed) until the engine idles
smoothly.
0.025 in.
(0.635 mm.)
NOTE: The tines should not rotate when the engine idles.
3. If the tines rotate when the engine idles, turn the idle
speed screw counterclockwise 1/8 of a turn at a time
(as needed), to reduce idle speed.
Checking the fuel, cleaning the air filter, and adjusting
the idle speed should solve most engine problems. If not
and all of the following are true:
• the engine will not idle
• the engine hesitates or stalls on acceleration
• there is a loss of engine power
Have the carburetor adjusted by a Sears or other
qualified service dealer.
Fig. 23
Do not sand blast,
scrape or clean
electrodes. Grit in the engine could damage
the cylinder.
WARNING:
4. Install a correctly-gapped spark plug in the cylinder
head. Turn the 5/8 in. socket clockwise until snug.
If using a torque wrench torque to:
110-120 in.•lb. (12.3-13.5 N•m)
Do not over tighten.
SPARK ARRESTOR MAINTENANCE
Idle Adjustment Screw
1. Remove the muffler cover. See Rocker Arm Clearance.
2. With a flat blade screwdriver or Torx T-20 bit,
remove the screw attaching the spark arrestor cover
to the muffler (Fig. 24).
1
2
Muffler
Spark Arrestor Screen
3
Tab
Fig. 22
Screw
Spark Arrestor Cover
Slot
Fig. 24
REPLACING THE SPARK PLUG
Use a replacement Champion RDZ19H spark plug. The
correct air gap is 0.025 in. (0.635 mm.). Remove the plug
after every 25 hours of operation and check its
condition.
1. Stop the engine and allow it to cool. Grasp the plug
wire firmly and pull the cap from the spark plug.
2. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning it
counterclockwise with a 5/8” socket.
3. Replace cracked, fouled or dirty spark plug. Set the air
gap at 0.025 in. (0.635 mm.) using a feeler gauge (Fig. 23).
3. Pull the tab on the spark arrestor cover out of the
muffler. Remove the spark arrestor cover.
4. Remove the spark arrestor screen from the spark
arrestor cover.
5. Clean the spark arrestor screen with a wire brush or
replace it.
6. Reinstall the spark arrestor screen, spark arrestor
cover and screw.
15
MAINTENANCE AND REPAIR INSTRUCTIONS
ROCKER ARM CLEARANCE
The rocker arm clearance may need adjustment if your
unit suffers a loss of performance power or has trouble
starting. Adjusting the rocker arm clearance requires
disassembly of the engine. If you feel unsure or
unqualified to perform this, take the unit to a Sears or
other qualified service dealer.
NOTE: Inspect the valve to rocker arm clearance with a
feeler gauge after the first 10 hours of operation
and then every 25 hours of operation thereafter.
• The engine must be cold when checking or adjusting
the valve clearance.
• This task should be performed inside, in a clean,
dust free area.
To adjust the rocker arm clearance:
1. Remove the two (2) screws on top of the engine cover
with a Flat-head or T-25 Torx screwdriver (Fig. 25).
Top View Of The Engine
Remove
Screws
Engine Cover
Screw
Fig. 26
3. Disconnect the spark plug wire.
4. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning it
counterclockwise with a 5/8” socket.
5. Remove the engine cover.
NOTE: To ease engine cover removal, pull the starter
rope out a little to give some slack.
6. Clean dirt from around the rocker arm cover.
Remove the screw holding the rocker arm cover with
a large flat blade screwdriver or Torx T-25 bit
(Fig. 27). Remove the rocker arm cover and gasket.
Rocker Arm Cover
Gasket
Muffler
Fig. 25
2. Remove the screw behind the engine cover (Fig. 26).
16
Spark Plug Hole
Fig. 27
MAINTENANCE AND REPAIR INSTRUCTIONS
7. Pull the starter rope slowly to bring the piston to the top
of its travel, (known as top dead center). Check that:
• The piston is at the top of its travel while looking in
the spark plug hole (Fig. 27)
• Both rocker arms move freely, and both valves are
closed
If these statements are not true, repeat this step.
8. Slide the feeler gauge between the rocker arm and
the valve return spring. Measure the clearance
between the valve stem and rocker arm (Fig. 29).
Measure both the intake and exhaust valves.
The recommended clearance for both intake and
exhaust is 0.003 – 0.006 in. (0.076 – 0.152 mm). Use a
standard automotive 0.005 in. (0.127 mm) feeler gauge.
The feeler gauge should slide between the rocker arm
and valve stem with a slight amount of resistance,
without binding. See Figure 28 and 29.
Adjusting Nuts
Rocker Arms
Adjusting Nut
Rocker Arm
0.003–0.006 in.
(0.076–0.152 mm)
Feeler Gauge
Valve Stem
Fig. 29
9. If the clearance is not within specification:
a. Turn the adjusting nut using a 5/16 inch (8 mm)
wrench or nut driver (Fig. 29).
INTAKE
• To increase clearance, turn the adjusting nut
counterclockwise.
EXHAUST
• To decrease clearance, turn the adjusting nut
clockwise.
b. Recheck both clearances, and adjust as necessary.
Feeler Gauge
Fig. 28
10. Reinstall the rocker arm cover using a new gasket.
Torque the screw to 20–30 in•lb (2.2–3.4 N•m).
11. Reinstall the engine cover. Check alignment of the
cover before tightening the screws. Tighten screws.
12. Check the spark plug and reinstall. See Replacing
the Spark Plug.
13. Replace the spark plug wire.
17
MAINTENANCE AND REPAIR INSTRUCTIONS
Cleaning the Unit
To avoid serious
personal injury,
always turn the unit off and allow it to cool
before you clean or perform any
maintenance on it.
WARNING:
•
•
Use a small brush to clean off the outside of the unit
and to keep the air vents free of obstructions.
Do not use strong detergents or petroleum based
cleaners, such as kerosene. Some household
cleaners contain aromatic oils such as pine and
lemon that can damage the plastic housings or
handles. Wipe off any moisture with a soft cloth.
Storage
•
•
•
•
•
Never store the unit with fuel in the tank where
fumes may reach an open flame or spark.
Allow the engine to cool before storing.
Store the unit in a locked up area to prevent
unauthorized use or damage.
Store the unit in a dry, well-ventilated area. Do not
store next to corrosive material like fertilizer.
Store the unit out of the reach of children.
Long Term Storage
If the unit will be stored for an extended time:
1. Carefully drain all gasoline from the fuel tank by
removing the fuel cap and tipping the motor housing
over to allow the fuel to drain into an approved gas
container. Do not use gas that has been stored for
more than 60 days. Dispose of the old gasoline in
accordance with Federal, State and Local
regulations.
18
2. Start the engine and allow it to run until it stalls. This
ensures that all gasoline has been drained from the
carburetor.
3. Allow the engine to cool. Remove the spark plug and
put 5 drops of high quality motor oil into the cylinder.
Pull the starter rope slowly to distribute the oil.
Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil
from the cylinder before attempting to start the
unit after storage.
4. Change the oil, referring to the Changing the Oil
section. Dispose of the old oil in accordance with
Federal, State and Local regulations.
5. Thoroughly clean the unit and inspect for any loose
or damaged parts. Repair or replace damaged parts
and tighten loose screws, nuts or bolts.
6. To take up less storage area, loosen the handlebar
knobs and fold the handlebar down. The unit is
ready for storage.
Transporting
•
Allow the engine to cool before transporting.
•
Secure the unit while transporting.
•
Drain the fuel tank before transporting.
•
Tighten fuel cap before transporting.
TROUBLESHOOTING
ENGINE WILL NOT START
CAUSE
ACTION
Empty fuel tank
Fill fuel tank with new fuel
Primer bulb wasn't pressed enough
Press primer bulb fully and slowly 10 times
Engine is flooded
Pull starter rope repeatedly with throttle control fully
engaged and with the choke lever in Position 3
Old fuel
Drain gas tank and add fresh fuel
Fouled spark plug
Replace or clean the spark plug
Plugged spark arrestor
Clean or replace spark arrestor
On/Off Control is in the OFF (O) position
Move switch to ON (I)
ENGINE WILL NOT IDLE
CAUSE
ACTION
Air filter is plugged
Replace or clean the air filter
Drain gas tank and add fresh fuel
Improper carburetor adjustment
Adjust according to the Carburetor Adjustments section
ENGINE WILL NOT ACCELERATE
CAUSE
ACTION
Drain gas tank and add fresh fuel
Improper carburetor adjustment
Take unit to a Sears or other qualified service dealer for
an adjustment
Dirty air filter
Clean or replace the air filter
Plugged spark arrestor
Clean or replace spark arrestor
ENGINE LACKS POWER OR STALLS WHEN UNDER LOAD
CAUSE
ACTION
Drain gas tank and add fresh fuel
Improper carburetor adjustment
Take unit to a Sears or other qualified service dealer for
an adjustment
Fouled spark plug
Replace or clean the spark plug
Plugged spark arrestor
Clean or replace spark arrestor
Low power
Rocker arm clearance adjustment (see page 18)
Cultivator tines bound with dirt or grass
Stop the unit, switch the On/Off Stop Control to
STOP, clean and remove any debris binding the tines
SIGNS OF OIL AROUND OIL FILL PLUG/DIPSTICK
CAUSE
Oil fill plug/dipstick loose or missing o-ring
ACTION
Tighten oil fill plug/dipstick, replace o-ring
UNIT OCCASIONALLY HESITATES AT HIGH SPEEDS
C A U SE
Spark plug gap is too small/close
ACTION
Adjust gap to 0.025”
NOTE: For repairs beyond the minor adjustments listed above, contact your nearest Sears Parts &
Repair center (1-800-4-MY-HOME®) or other qualified service dealer for an adjustment.
19
SPECIFICATIONS
ENGINE*
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 4-Cycle
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 cu. in. (26.2 cc)
Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,000-3,600 rpm
Operating RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,200-8,800 rpm
Clutch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centrifugal
Ignition Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic
On/Off Stop Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rocker Switch
Valve clearance (intake and exhaust) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.003–0.006 in. (0.076–0.0152 mm)
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 inch (0.635 mm)
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAE 30 Oil
Crankcase Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.04 oz (90 ml)
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unleaded
Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diaphragm, All-Position
Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Incredi-Pull™ Starting Auto Rewind
Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baffled with Guard
Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spring Return
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 oz (444 ml)
CULTIVATOR*
Cultivating Path Width (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 inches (22.86 cm)
Cultivating Depth (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 inches (15.24 cm)
Approximate Weight (no fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 lb. (11.5 kg)
*All specifications are based on the latest product information available at the time of printing. We reserve the right to
make changes at any time without notice.
20
NOTES
21
NOTES
22
CULTIVADORA / BORDEADORA
Modelo No. 316.292711
with
• SEGURIDAD
• MONTAJE
• FUNCIONAMIENTO
• MANTENIMIENTO
• LISTADO DE PIEZAS
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.
Vaya a: www.sears.com/craftsman
P/N 769-02846
(1/07)
Sears, Roebuck and Co., Hoffman Estates, IL 60179
PARACHISPAS
PROPOSICIÓN 65 DE CALIFORNIA
ADVERTENCIA
LAS EMISIONES DEL MOTOR DE ESTE
PRODUCTO CONTIENEN SUBSTANCIAS
QUIMICAS QUE EL ESTADO DE
CALIFORNIA CONOCE COMO CAUSANTES
DECANCER, DEFECTOS DE NACIMIENTO
U OTROS DAÑOS REPRODUCTIVOS.
24
SIGNIFICADO
SIMBOLO
SIGNIFICADO
• IMPORTANTE INFORMACION DE SEGURIDAD •
LEA TODAS LAS INSTRUCCIONES ANTES DE
OPERAR LA UNIDAD
AVISOS DE SEGURIDAD PARA LAS UNIDADES
QUE FUNCIONAN CON GASOLINA
25
26
GUARDE ESTAS INSTRUCCIONES
SIGNIFICADO
SIMBOLO
SIGNIFICADO
• LOS OBJETOS DESPEDIDOS Y
LA CUCHILLA ROTATIVA
PUEDEN CAUSAR GRAVES
LESIONES
• CONTROL DE ENCENDIDO Y
APAGADO
ENCENDIDO /ARRANQUE /MARCHA
• USE PROTECCION OCULAR Y
AUDITIVA
• CONTROL DE ENCENDIDO Y
APAGADO
APAGADO o PARADO
• CONTROL DEL OBTURADOR
1
• MANTENGA ALEJADOS A LOS
ESPECTADORES
2
3
– LAS PUAS GIRATORIAS
PUEDEN CAUSAR GRAVES
LESIONES
27
OFF/
APAGADO (O)
ON/
ENCENDIDO (I)
Manubrio
Púas
28
CONEXIÓN DE LA RUEDA Y DE LA
CUCHILLA DE LA BORDEADORA
Fig. 1
Orificio
Arandela
Fig. 2
CARGA E ACEITE EN EL CARTER DEL
CIGÜEÑAL: USO INICIAL
Fig. 5
Fig. 6
Fig. 7
Orificio de llenado
de aceite
Fig. 8
30
•
Fig. 9
31
INSTRUCCIONES DE ARRANQUE Y APAGADO
ENCENDIDO / ON
ADVERTENCIA:
APAGADO/
OFF
ADVERTENCIA:
Cultivadora
Equipado con
Incredi-Pull™
Fig. 12
Fig. 13
33
evitar
ADVERTENCIA: Para
lesiones
PROGRAMA DE MANTENIMIENTO
FRECUENCIA
MANTENIMIENTO REQUERIDO
CONSULTE
Página E9
Página E13
Cada 10 horas
Página E14
Página E13
Página E13
Página E15
Cada 25 horas
Página E15
Diente “A”
Diente
“B”
Bujes
Fig. 14
34
PRECAUCION:
Fig. 17
Lleno
Agregue
41-44 ml
(1,4-1,5 Onzas)
Fig. 18
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION
MANTENIMIENTO DEL FILTRO DE AIRE
Limpieza del filtro de aire
Screen
Fig. 21
Cubierta del
filtro de aire
Ranura
Orejeta
limpie
PRECAUCION: No
con chorro
0,635 mm
(0,025 pulg.)
Fig. 23
1
3
Orejeta
Fig. 22
Ranura
Tornillo
Tornillo
Fig. 26
Fig. 25
Fig. 27
38
Brazos
oscilantes
Galga
0,076–0,152 mm
(,003–,006 pulg.)
Fig. 28
39
TRANSPORTE
40
42
PARTS LIST
REPLACEMENT PARTS - MODEL 316.292711
4-CYCLE GAS CULTIVATOR
Part Numbers On Following Page
2
1
58
3
4
5
18 19
20
6
23
21
22
7
24 25 27
26
8
10
13
48
30
20
31
9
12
44
29
28
11
43 42 14
34
32
33
35
37
41
36
15
39
45
46
39
47
50
17
49
51
40
38
16
55
54
56
57
52
59
91
53
58
88
60
64
90
88
63
89
61
80
79
87
62
81
68
78
66
77
67
65
76
85
86
75
73
82
70
74
83
84
69
72
71
43
PARTS LIST
REPLACEMENT PARTS - MODEL 316.292711
4-CYCLE GAS CULTIVATOR
Item Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
753-04028
791-181930
791-182651
791-182652
791-181025
791-182098
791-182099
791-182340
791-182101
791-182100
791-182341
791-182103
791-181038
791-182102
791-181033
753-04816
17
18
19
20
21
22
23
24
25
26
27
791-181003
753-1226
791-182749
753-04993
753-04029
791-182348
791-182732
753-1225
753-04030
753-04031
753-05467
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
791-182097
791-181000
791-182409
791-182657
791-182658
791-182659
753-04033
791-182352
791-182353
753-04034
791-181080
791-182236
753-04035
791-182356
753-1232
791-181048
753-04036
791-180890
791-181045
791-181046
791-182361
44
Description
Engine Cover Assembly (includes 3 & 4)
Engine Cover Screw
Starter Rope Eyelet
Eyelet Nut
Valve Cover Screw
Valve Cover
Valve Cover Gasket
Rocker Adjustment Nut
Rocker Arm Pivot
Rocker Arm
Rocker Arm Stud
Valve Spring Retainer
Valve Spring
Push Rod Guide
Push Rod
Cylinder Assembly
(includes 11-14, 17, 80 & 81)
Cylinder Screw
Intake Baffle
Carburetor Mount Gasket
Nut
Carburetor Mount (includes 20)
Carburetor Mount Screw
Carburetor Gasket
Carburetor with Primer
Air Filter O-Gasket
Air Filter Mounting Screw
Air Filter Cover Assembly
(includes 28, 29, 31-33)
Breather Tube Assembly
Grommet Washer
Washer
Air Filter Plate
Air Filter
Air Filter Cover
Fuel Cap
Fuel Return Line
Fuel Pick-Up Line with Filter
Fuel Tank Assembly (includes 34-36)
Screw
Washer
Bushing
Fuel Tank Shield
Muffler Baffle
Muffler Gasket
Muffler (includes 43, 45-47)
Spark Arrestor Screen
Screen Cover
Screw
Muffler Mounting Screw
Item Part No.
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
*
*
*
753-04288
753-1202
753-05074
753-05072
753-04286
791-182366
753-05011
791-611061
791-182661
791-181020
753-05075
791-182537
791-182396
753-1238
791-153592
753-05076
791-181345
791-182519
753-05077
791-180217
753-04039
753-04040
753-05078
791-182736
791-181861
791-182743
753-05079
791-182375
791-182379
753-04919
791-181012
791-181040
791-182374
791-181018
791-182377
791-181020
753-04041
791-182290
791-181009
791-181008
753-04878
753-05176
753-04801
791-180852B
753-05081
Description
Palnut
Plate Screw
Pressure Plate Assembly (includes 50)
Recoil Pulley Assembly (includes 49 & 57)
Recoil Spring
Nut Clip
Pull Handle
Rope Guide
Rope
Housing Screw
Starter Housing Assembly (includes 49-58)
Wire Grommet
Clutch Washer
Clutch with Washer
Clutch Drum
Clutch Cover Assembly (includes 65-68)
Clutch Cover Screw
Anti-Rotation Screw
Screw
Nut
Lead Wire
Ignition Module with Screws
Spacer
Flywheel
Screw
Shroud Assembly (includes 73)
Crankcase Assembly (includes 76 & 77)
90° Elbow
Breather Hose
Cam Bracket Assembly
Cam Bracket Screw
Valves, Intake and Exhaust
Cylinder Gasket
Oil Pan Gasket
Oil Pan (includes 82 & 84)
Oil Pan Screw
Dipstick Assembly (includes 86)
O-Ring
Connecting Rod
Wrist Pin Button
Piston (includes 91)
Wrist Pin
Piston Ring Set
Spark Plug
Short Block Assembly (includes 5-17, 75-91)
Parts not shown
PARTS LIST
REPLACEMENT PARTS - MODEL 316.292711
4-CYCLE GAS CULTIVATOR
1
3
4
2
5
6
13
7
8
11
4
14
11
17
16
10
18
12
15
33
9
20
19
25
22
24
23
21
34
31
20
28
30
32
36
27
26
29
31
Item Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
753-04042
753-04043
791-182673
753-04044
753-04147
753-04498
791-182899
753-04049
753-04499
791-182677
753-04052
753-04053
753-04054
753-04055
753-04056
753-04057
753-04058
753-04059
Description
Trottle Control
Torsion Spring
On/Off Switch
Foam Grip
Throttle Cable
Upper Handle
Bolt
Cable Tie
Flex Shaft
Knob
Saddle Washer
Lower Handle
Screw
Front Handle
Lock Nut
Cotter Pin
Tailpiece Bracket Assembly
Clevis Pin
Item Part No.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
753-04060
753-04061
753-04062
753-04063
753-04064
753-05001
753-05080
753-04075
753-04074
753-04073
753-04072
753-04071
753-04070
753-04069
753-04068
753-05469
791-180288
Description
Cap Screw
Lock Nut
Cap Push
Wheel Support Bracket Assembly
Wheel
Cap Screw
Tine Shield
Gear Box Assembly
Inner Tine (right side)
Outer Tine (right side)
Inner Tine (left side)
Outer Tine (left side)
Click Pin
Edger Tine
Edger Wheel
Drive Shaft Housing
Anti Rotation Screw
45
46
Repair Protection Agreements
Congratulations on making a smart purchase.
Your new Craftsman® product is designed and
manufactured for years of dependable operation. But like all products, it may require repair
from time to time. That’s when having a Repair
Protection Agreement can save you money and
aggravation.
Purchase a Repair Protection Agreement now
and protect yourself from unexpected hassle
and expense.
Here’s what’s included in the Agreement:
ã Expert service by our 12,000 professional
repair specialists
ã Unlimited service and no charge for parts
and labor on all covered repairs
ã Product replacement if your covered product can’t be fixed
ã Discount of 10% from regular price of
service and service-related parts not covered by the agreement; also, 10% off regular
price of preventive maintenance check
ã Fast help by phone – phone support from a
Sears technician on products requiring in-home
repair, plus convenient repair scheduling
Once you purchase the Agreement, a simple
phone call is all that it takes for you to schedule
service. You can call anytime day or night, or
schedule a service appointment online.
Sears has over 12,000 professional repair specialists, who have access to over 4.5 million
quality parts and accessories. That’s the kind of
professionalism you can count on to help prolong the life of your new purchase for years to
come. Purchase your Repair Protection Agreement today!
Some limitations and exclusions apply.
For prices and additional information call
1-800-827-6655.
Sears Installation Service
For Sears professional installation of home
appliances, garage door openers, water heaters,
and other major home items, in the U.S.A. call
1-800-4-MY-HOME®
47
Get it fixed, at your home or ours!
Your Home
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-888-SU-HOGAR
SM
(1-888-784-6427)
1-800-361-6665 (Canada)
Au Canada pour service en français:
1-800-LE-FOYERMC
(1-800-533-6937)
www.sears.ca
® Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co.
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears, Roebuck and Co.
MC Marque de commerce / MD Marque déposée de Sears, Roebuck and Co.
© Sears, Roebuck and Co.