advertisement
▼
Scroll to page 2
of
20
![Chicago Electric 94761 User manual | Manualzz Chicago Electric 94761 User manual | Manualzz](http://s1.manualzz.com/store/data/003079507_1-8f63002329dcf9c04ff465dc020aeb3a-360x466.png)
PORTABLE FLUORESCENT WORKLIGHT 94761 Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com To prevent serious injury, read and understand all warnings and instructions before use. Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. Specifications Power Requirement 120 V~, 60 Hz Fluorescent Bulb 25 watt CA-9 Type Line Cord 6’ (L); Two-prong plug Light Frame Dimensions 9-1/8” (dia.) X 10-1/2” (L) Switch Round, push button Weight 4.5 lb. E197534 Save This Manual You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Write the product’s serial number in the back of the manual near the assembly diagram, or write month and year of purchase if product has no number. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate lights in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Lights create sparks which may ignite the dust or fumes. 3. Keep bystanders, children, and visitors away while operating a light. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. Electrical Safety 1. 94761 Grounded lights must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding For technical questions, please call 1-800-444-3353. English Page prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the lights should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 2. Double insulated lights are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system. 3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 4. Do not abuse the Power Cord. Never use the Power Cord to carry the lights or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock. 5. When operating a light outside, use an outdoor extension cord marked “W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock. Personal Safety 1. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the light in unexpected situations. 2. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Always wear ANSI-approved safety goggles and a dust mask/respirator when performing maintenance on this light. Light Use And Care 1. Use the correct light for your application. Do not use the light for a purpose for which it is not intended. 2. Disconnect the Power Cord Plug from the power source before making any adjustments, changing accessories, or storing the light. Such preventive safety measures reduce the risk of starting the light accidentally. Always unplug the light from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 3. Store idle lights out of reach of children and other untrained persons. Lights are dangerous in the hands of untrained users. 94761 For technical questions, please call 1-800-444-3353. English Page 4. Maintain lights with care. Do not use a damaged light. Tag damaged lights “Do not use” until repaired. 5. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the light’s operation. If damaged, have the light serviced before using. Many accidents are caused by poorly maintained lights. 6. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one light may become hazardous when used on another light. Service 1. Light service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a light, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounded Lights: Lights With Three Prong Plugs 1. Lights marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the light should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the light. The green wire in the cord must be the only wire connected to the light’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) 94761 For technical questions, please call 1-800-444-3353. English Page Your light must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) 3. FIGURE A FIGURE B Double Insulated Lights: Lights With Two Prong Plugs 1. Lights marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 2. Double insulated lights may be used in either of the 120 volt outlets shown in the preceding illustration. (See Figure B.) Extension Cords 1. Grounded lights require a three wire extension cord. Double Insulated lights can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible light damage. (See Figure C, next page.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.) 4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure C.) 5. If you are using one extension cord for more than one light, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 94761 For technical questions, please call 1-800-444-3353. English Page 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 or 240 VOLT) NAMEPLATE AMPERES EXTENSION CORD LENGTH (at full load) 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - FIGURE C * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ A Volts Alternating Current Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) 94761 For technical questions, please call 1-800-444-3353. English Page Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SPECIFIC SAFETY RULES WARNING: When using outdoor use portable lamps, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS Use only three-wire outdoor extension cords that have three-prong groundling plugs and grounding receptacles that accept the appliance’s plug. Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the wet location portable lamp. Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety. Use only with an extension cord for outdoor use, such as an extension cord of cord type SW, SW-A, SOW, SOW-A, STW, STWOA, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, or SJTOW, SJTOW-A. SAVE THESE INSTRUCTIONS Operation Instructions 1. Press the Switch (16) once to turn the light on and again to turn the light off. 2. To adjust the angle of the Worklight, set the Worklight down and turn the round adjusting knob on the side of the Worklight counter-clockwise. 3. Once loosened, the body of the Worklight can be adjusted to move up or down. Turn the adjusting knob clockwise to the tighten the knob and lock the Worklight body in place. Bulb Replacement 1. Unplug the lamp and allow the bulb to cool completely. 2. Peel back the covers of the four Tap Screws (1) that are located on the top, bottom, right and left sides of the Lamp Cover (2). 94761 For technical questions, please call 1-800-444-3353. English Page 3. Using a screwdriver (not included), unscrew the four 3 X 12 Tap Screws (1). 4. Remove the Lamp Cover (2), Sponge Strip (3), Rubber Ring (4) and then the Glass covering (5). 5. Unscrew the Lamp Tube (6) and remove from the body of the Worklight. Replace with a similar 25 watt fluorescent bulb set. 6. Put the Glass covering (5), Rubber Ring (4), Sponge Strip (3) and Lamp Cover (2) back into place. Then place the Lamp Cover (2) back into place and tighten with the four 3 X 12 Tap Screws (1). INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure the Power Switch of the tool is in its “OFF” position, that the tool is unplugged from its electrical outlet, and that the bulb is allowed to cool completely before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. Warranty Limited 90 Day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 94761 For technical questions, please call 1-800-444-3353. English Page PARTS LIST Part Q’ty Part Q’ty 1 Tap Screw 3 X 12 4 12 PVC Handle 1 2 Lamp Cover 1 13 Left and Right Handle 1 3 Sponge Strip 1 14 1 4 Rubber Ring 1 15 Power Cord 1 5 Glass 1 16 Switch (include Cap and Seal Ring) 1 6 Lamp Tube 1 17 Seal Ring 2 7 Reflector 1 18 Screw 2 8 Tap Screw 3 X 14 2 19 Bracket 2 9 Fender 2 20 Plastic Connecting Pipe 2 10 Housing 1 21 Lamp Holder 1 11 Tap Screw 3 X 14 4 PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. 94761 For technical questions, please call 1-800-444-3353. English Page ASSEMBLY DIAGRAM Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 94761 For technical questions, please call 1-800-444-3353. English Page 10 IMPORTANT! ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visitez notre site Web : http://www.harborfreight.com 120 V~, 60 Hz 25 watt Type CA-9 6’ (L) ; fiche de deux fourchons Mesures de la lampe 9-1/8’’ (dia.) x 10-1/2’’ (L) Poids 4.5 livres (2 kilos) E197534 . 3. 94761 . 3. 4. 5. . EMPLOI ET MAINTIENT DE CETTE LAMPE 1. 94761 . 3. 4. 5. 6. SERVICE 1. . 94761 LAMPES MISES ÀTERRE : LAMPES AVEC FICHES DETROIS FOURCHONS 1. . 3. L’image A L’image B LAMPES DOUBLEMENT ISOLÉES : LAMPES AVEC FICHES DE DEUX FOURCHONS 1. . CORDONS PROLONGATEURS 1. . 94761 4. 5. 6. 7. 8. CALIBRE DE FIL MINIMUM RECOMMANDÉ POUR CORDONS PROLONGATEURS (120 OU 240 VOLT) LONGUEUR DE CORDON PROLONGATEUR 25 Pieds 50 Pieds 75 Pieds 100 Pieds 150 Pieds 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - Image C 94761 SYMBOLOGIE Doublement isolé Canadian Standards Association Underwriters Laboratories, Inc. V~ A GARDEZ CES INSTRUCTIONS 94761 MODE D’EMPLOI 1. . 3. . 3. 4. 5. 6. INPECTION, MAINTIENT ET NETTOYAGE 1. . 94761 GARANTIE LISTE DES PARTIES Partie Q’té 1 Vis 3x12 4 12 1 2 1 13 1 3 1 14 Attache-câble 1 4 1 15 1 5 Vitre 1 16 1 6 Plomb de Lampe 1 17 Cachet 2 7 1 18 Vis 2 8 Vis 3x14 2 19 Support 2 9 Aile 2 20 2 10 Cadre 1 21 1 11 Vis 3x14 4 94761 Q’té TABLEAU D’ASSEMBLAGE 11 1 2 3 4 5 7 6 13 10 14 15 8 16 17 21 18 19 20 LISEZ ATTENTIVEMENT CE QUI SUIT LE FABRICANT ET-OU LE DISTRIBUTEUR A FOURNI LA LISTE DE PIÈCES ET LE DIAGRAMME DE MONTAGE DANS CE MANUEL COMME UN INSTRUMENT DE RÉFÉRENCE SEULEMENT. AUCUN LE FABRICANT OU LE DISTRIBUTEUR FONT N’IMPORTE QUELLE REPRÉSENTATION OU GARANTIE DE N’IMPORTE QUELLE SORTE À L’ACHETEUR QU’IL OU ELLE EST AUTORISÉ POUR FAIRE N’IMPORTE QUELLES RÉPARATIONS AU PRODUIT, OU QU’IL OU ELLE EST AUTORISÉ POUR REMPLACER N’IMPORTE QUELLES PIÈCES DU PRODUIT. EN FAIT, LE FABRICANT ET-OU LE DISTRIBUTEUR DÉCLARE EXPRESSÉMENT QUE TOUTES LES RÉPARATIONS ET LES REMPLACEMENTS DE PIÈCES DEVRAIENT ÊTRE ENTREPRIS PAR LES TECHNICIENS DIPLÔMÉS ET AGRÉÉS ET PAS PAR L’ACHETEUR. L’ACHETEUR SUPPOSE TOUT LE RISQUE ET LA RESPONSABILITÉ SURVENANT DU FAIT DE SES RÉPARATIONS AU PRODUIT ORIGINAL OU AUX PIÈCES DÉTACHÉES Y, OU SURVENANT DU FAIT DE SON INSTALLATION DE PIÈCES DÉTACHÉES Y. 94761 PDF created with pdfFactory Pro trial version www.pdffactory.com 9 12
advertisement