hard floor
polisher
generation future
English
GB
Italiano
IT
FR
DE
ES
PT
PL
RU
USER INSTRUCTIONS
2
IMPORTANT SAFETY REMINDERS
GB
This polisher should only be used for domestic polishing of hard floor surfaces as
described in these instructions. Please ensure that these are fully understood before
operating this appliance.
This polisher must not be used for floor washing.
This Hoover suction polisher must be connected to an electricity supply at the
voltage shown on the rating plate, found on the underside of the polisher.
Appliances showing a rating plate voltage of 230V- 240V can be connected to
electrical sources of 220V.
This product is double insulated and must not be earthed.
IMPORTANT: The wires in the power cord are coloured in accordance with the following code:
Blue - Neutral Brown - Live
13 Amp fused plug on UK versions only.
GETTING STARTED
By following this step-by-step guide your new Hoover polisher will be ready
for use:
Remove polisher and accessories from packaging. Please dispose of
the packaging in a safe and environmentally conscientious way.
HANDLE ASSEMBLY
Join together the 2 handle sections ensuring that the stud locates in the hole
(Fig.1).
Fit the handle into the socket at the rear of the hood and push until it locates
in the hole (indicated by a "click") (Fig. 2).
OUTER BAG ASSEMBLY
Attach bag support to the hook positioned under the hand grip (Fig. 3).
Once the bag support is attached, insert plastic flange at the bottom of bag
into the opening located at the rear of the hood (Fig. 4).
FITTING THE PAPER DUST BAG
(Depending on model)
Refer to the following instructions for models equipped with paper
dust bag:
1) Open fastener on outer bag to the fullest extend to expose the
air-duct.
2) Fit paper dust bag by pushing the cardboard collar on the air-duct (Fig. 5).
3) Tuck paper dust bag into the outer bag and fully close the zip fastener.
3
GB
SAFETY WARNING: The polisher must be switched off and the plug
disconnected from the electrical supply before fitting or changing the
brushes.
Turn the polisher upside down. Place each brush or pad on its axle and
press until a click indicates that it is the correct position. To remove
brushes or pads, grasp them and pull towards you.
Your polisher is now ready for use.
SWITCHING THE POLISHER ON
Ensure the handle is in the upright position before inserting the plug
into the electricity supply.
To start the polisher push the handle down then lower it into the
working position.
To stop the polisher simply return handle to the upright position.
SAFETY WARNING: Do not run over main leads to avoid damage to
the electrical insulation.
INDICATOR LIGHTS (FIG. 6)
(Depending on model)
Some polishers will have 4 indicator lights on the front panel:
Green light on: the appliance is connected to the electricity supply
Red light on: paper dust bag needs changing
1 orange light on: motor running at low speed
2 orange lights on: motor running at normal speed
ADJUSTING BRUSH SPEED (FIGS 6 & 7)
(Depending on model)
Models equipped with 4 indicator lights on panel (Fig. 6), are supplied
with a 2 - position foot switch (Fig. 7). During the wax-spreading
phase with the Yellow or Black brushes, press the foot switch to
reduce brush rotation speed, reduce noise level and save energy.
When the rotation speed is low one Orange light is illuminated
When the wax-spreading operation is finished, press the foot switch
(Fig. 7) to return to high speed and start the polishing phase.
When the rotation speed is high two Orange lights are illuminated
SAFETY WARNING: The polisher must be switched off and the plug
disconnected from the electrical supply before fitting or changing the
brushes.
4
GB
ACCESSORIES
Hoover polishers are equipped with spring loaded brushes and pads in
order to obtain the best results even on floors with uneven surface.
For this reason, the small narrow brush positioned on the front of the
hood is also spring loaded.
Three kits of brushes and pads are supplied with the polisher:
Yellow Hard Bristle Brushes (Depending on model)
To be used to remove the old polish then to spread the new wax evenly on
the floor. Particularly suitable for marble and tiles.
Black Soft Bristle Brushes
Must be used to complete the first polishing phase. Suitable for all hard floors.
Grey Buffing Pads
To be used during the final polishing phase for producing a high gloss.
They can be used on all hard surfaces, but are especially suitable for marble
and tiles.
Natural White Pads ( Depending on model)
These natural white pads, made mainly of wool, have been especially
designed to polish wooden floors. They should be used after the Black soft
bristle brushes.
TO WAX AND POLISH THE FLOORS
TO WAX THE FLOORS
Before applying polish, ensure that the surface is clean. Remove any greasy
stains using a damp cloth.
To apply the polish, follow the instructions supplied with the polish.
Use a good quality polish, spreading it evenly. After the polish has
dried, polish the floor with the yellow hard texture brushes or the
softer black brushes.
TO POLISH THE FLOORS
For producing a high gloss, use the natural white pads for wooden floors or
grey buffing pads for all other hard surfaces.
To obtain better results, always move the polisher in straight lines rather than
in circles.
Buffing pads should only be used after the whole surface has first been
polished with brushes.
5
GB
The suction polisher collects dust in the bag. To maintain the efficiency
of your polisher check the dust level and empty the cloth bag or replace the
paper dust bag frequently.
MODELS EQUIPPED WITH PAPER DUST BAG:
Fully open zip fastener and remove paper dust bag by pulling the cardboard
collar from the air duct (Fig. 5).
Fit new paper dust bag as described in paragraph "Fitting the paper dust
bag".
MODELS EQUIPPED WITH BAG CHECK INDICATOR:
On these models the red light will switch on when paper dust bag needs to be
replaced.
MODELS EQUIPPED WITH CLOTH BAG (WITHOUT
PAPER DUST BAG):
Remove the cloth bag from upper plastic clip (Fig. 8) and disconnect bottom
plastic flange from hood pressing lightly on the indent on the flange.
Turn cloth bag upside down and shake gently (Fig. 9).
The cloth bag can be washed. We suggest hand washing it in warm water
with a mild detergent.
CLEANING BRUSHES AND PADS
Brushes may be washed in warm water with a mild detergent.
Pads may be gently brushed with soapy water and wiped with a damp cloth. Do not
immerse the pads in the soapy water.
Allow the pads to dry thoroughly before use, keeping them flat.
TRANSPORT, MAINTENANCE AND STORAGE
Move the polisher by means of the rear wheels.
Wind supply cord around the 2 clips on the handle tube.
To maintain brushes in good condition, always remove them before storing the
polisher.
6
GB
SIMPLE USER CHECK LIST BEFORE CALLING FOR
SERVICE
1) Is there a working electricity supply to the polisher? Check with another
appliance.
2) Is a restriction causing the bag check indicator to be activated in use?
If yes: Is the dust bag full? Please refer to chapter "Fitting the Paper Dust Bag".
Please remember: A service charge will be made if the polisher is examined and
found to be in working order, has not been assembled in accordance with these
instructions, or has been misused.
DO
Call your nearest Hoover Service Centre in the event of dissatisfaction
Ensure that all service and repairs are carried out by an authorised Hoover Service
Engineer.
Only use genuine Hoover parts.
Replace the paper dust bag as soon as the bag check indicator activates.
Always switch off and remove the power plug from the electricity supply after use
and before cleaning the appliance or attempting user maintenance as described in
these instructions.
Remember: Electricity can be dangerous.
DO NOT
Use your polisher out of doors, on wet surfaces or for wet pick up.
Pick up matches, hot ashes, cigarette ends or anything that may damage the
product.
Spray with or pick up flammable liquids, cleaning fluids, aerosols or their vapours as
this may cause risk of fire/explosion.
Run over, stand on, or wrap the power cord around arms or legs when using your
cleaner
Remove the plug by pulling on the power cord.
Continue to use your polisher if it or the plug/power cord appears to be faulty or
damaged. To avoid safety hazards the polisher must only be repaired by an
authorised Hoover Service Engineer.
TECHNICAL ASSISTANCE SERVICE
Please contact the nearest Hoover Spare Parts Point for any information and for the
supply of spare parts.
Ensure that all the repairs are carried out by Hoover authorised personnel only.
Before cleaning and maintenance by the owner, remember to switch off the appliance and pull out the plug.
7
GB
SPARE PARTS
Use only original Hoover spare parts.
Natural white pads (Kit 3 pieces):
Code Z9 (Art. 09026163)
Grey buffing pads (Kit 3 pieces):
Code Z5 (Art. 09502576)
Black Soft Bristle Brushes (Kit 3 pieces):
Code Z6 (Art. 09410523)
Yellow Hard Bristle Brushes (Kit 3 pieces)
Code Z7(Art. 09787037)
Paper Dust Bag
Code H29 (Art. 09178369)
GUARANTEE STATEMENT
The guarantee conditions for this appliance are as defined by our representative in
the country in which it is sold. Details regarding these conditions can be obtained
from the dealer from whom the appliance was purchased. The bill of sale or receipt
must be produced when making any claim under the terms of this guarantee.
Subject to change without notice.
UK
HOOVER LTD Pentrebach,
Merthyr Tydfil, Mid Glamorgan
CF48 4TU
GIAS Customer Sevice
08705 400600
Hoover Spares 01204 556111
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. The symbol on the product indicates that this
product may not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. Disposal must be carried out
in accordance with local environmental regulations for waste disposal. For more detailed information about
treatment, recovery and recycling of this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
8
IMPORTANTI CONSIGLI DI SICUREZZA
IT
9
IT
INSERIMENTO SPAZZOLE
10
IT
ACCESSORI
11
12
IT
13
IT
SVIZZERA
CANDY HOOVER AG
Boesch 21
CH-6331 Huenenberg
Telefon: 041-7854040
Gias Customer Service
0848/780 780
14
CONSIGNES DE SECURITE IMPORTANTES
FR
15
FR
16
FR
ACCESSOIRES
17
18
FR
19
SUISSE
CANDY HOOVER AG
Boesch 21
CH-6331 Huenenberg
Telefon: 041-7854040
Gias Customer Service
0848/780 780
20
WICHTIGE SICHERHEITSHINWEISE
DE
21
DE
22
DE
23
DE
24
DE
25
DE
ÖSTERREICH
Candy Hoover Austria GmbH
Mariahilferstrasse 176
A-1150 Wien
Tel: 01-897 33 00
Fax: 01-897 33 00 99
Kundendienst: 0820-220 224
(0,15 Euro/min)
E-Mail: [email protected]
www.hoover.at
SCHWEIZ
CANDY HOOVER AG
Boesch 21
CH-6331 Huenenberg
Telefon: 041-7854040
Gias Customer Service
0848/780 780
26
ES
27
MONTAJE DE LOS CEPILLOS
ES
28
ES
ACCESORIOS
29
ES
30
ES
QUÉ
NO DEBE HACER
31
ES
32
PT
33
COLOCAÇÃO DAS ESCOVAS
PT
34
PT
ACESSÓRIOS
35
PT
36
37
38
39
40
41
42
NEDERLAND
Candy Nederland BV
Argonweg 7-11
3812 RB AMERSFOORT
Tel: 033-4224000
www.hoover.nl
Gias Customer Service
(Nederland) 0900/9999109
43
44
45
46
47
48
49
50
51
52
53
RU
54
55">
