Sharp XE-A202 Owner's manual

03.7.5 7:02 AM
Page 1
XE-A202 Quick Start Guide
English
For quick set-up, follow the steps shown below. Note that malfunction may occur if you do not follow the steps. For further information, please read the instruction manual. Before setting up your cash register, prepare
three new R6 or LR6 batteries (“AA” size), which are necessary for memory backup, and find a stable surface near an AC outlet where the cash register is not subject to water sources or direct sunlight.
1
Installing the Cash
Register
Install the cash register using the fixing
angle bracket provided with the register.
1. Thoroughly clean the location where
the fixing angle bracket (B) is to be
placed.
2. Peel off the adhesive tape on the
fixing angle bracket.
3. Hook the angle bracket onto the hook
(A) that is located at the bottom rear
of the register.
4. Firmly stick the fixing angle bracket to
the table surface that you cleaned
above.
2
Preparing the Cash Register
3
Initializing the Cash Register
To ensure the cash register operates properly, initialize it
using the following procedure.
Installing the Paper Roll
4
(for receipt printing)
1. Lift up the print roller release lever to unlock and open the
print roller arm
OPX/Z
Setting the Date
Enter the date in 8 digits using the daymonth-year format. Then press s.
Print roller
release lever
REG
MGR
X1/Z1
26082003
X2/Z2
3. Insert the plug of the AC power
cord into the AC outlet. A buzzer
will sound three times.
IMPORTANT: This operation must be performed
without batteries installed.
4. The register display should now show “
0.00”.
2. Set a paper roll in the paper roll cradle as per the diagram.
To the printer
Correct
To the printer
Incorrect
3. Feed the end of the paper along
with the paper
Paper positioning
positioning guides
guides
as per the diagram.
Install three new R6 or LR6 batteries (“AA” size) according
to the procedure shown below with the power cord
connected and set the mode switch to
REG position.
1. Lift the rear of the printer cover and
detach it.
To remove the register from the fixing
angle bracket:
1. Lift up the front of the register and
pull the register towards you.
s
2. Open the battery compartment
cover.
3. Install three new R6 or LR6
batteries (“AA”size) as per the
diagram.
When the batteries are properly
installed “ ” on the display will
disappear.
4. Close the battery compartment cover.
Setting the Time
Enter the time in 4 digits (“hhmm”
format) using the 24 hour system. Then
press s.
Example: Time (2:30 p.m.)
1430
s
Setting the VAT
Set the VAT rate in seven digits (3-digit
integer and 4-digit decimal).
Installing the Batteries
A
Example: Date (26 August, 2003)
PGM
NOTE: If the buzzer does not sound when the plug is
inserted, the initialization has not been done successfully.
Wait at least one minute after pulling out the plug, and
insert the plug again.
B
Set the mode switch to the PGM
position.
Print roller arm
1. Make sure the AC power cord is unplugged and
batteries are not installed on the register.
2. Insert the manager (MA) key into
the mode switch and turn it to the
REG position.
Basic Programming
Example: VAT1 rate 16%
4. While holding down the paper,
slowly close the print roller arm,
and push down the arm until you
hear a click locking the arm.
Make sure securely you push
down the center of the wing part
of the arm as per the diagram.
The paper will be fed
automatically.
5. Cut off the excess paper using
the edge of the inner cover, and
replace the printer cover. Press
the F key to make sure the
paper end comes out of the
printer cover and clean paper
appears.
NOTE: If the print roller arm is not securely locked, printing is
not done right. If this problem occurs, open the arm, and close
the arm as instructed above.
If you want to use a paper roll for journal printing, please refer
to GETTING STARTED section of the instruction manual.
s 9 @ 1 @ 16 @
sA
NOTE: Department 1 to 50 are set to
VAT1 by default.
Other programming
While the cash register is
preprogrammed so that it can be used
with minimal setup, you may need to
program some items such as
department texts and logo message.
For details of programming, please refer
to the instruction manual.
5
Now, you are ready for
sales entries.
Set the mode switch to the REG
position, and start registration. For
details of registration, please refer to the
instruction manual.
A202_Quick Start/A4(D)
03.7.5 6:58 AM
Page 1
1
2
OPX/Z
A
X1/Z1
X2/Z2
PGM
s 88 @ 1 A
MGR
4
REG
3
26082003
s
1430
s
5
HOTLINE NUMMER: 0180-51 51 666
A202_Quick Start/A4(F)
03.7.5 6:55 AM
Page 1
1
2
3
OPX/Z
X2/Z2
X1/Z1
MGR
A
REG
B
Vers
l’imprimante
Incorrect
26082003
s
s
A202_Quick Start/A4(S)
03.7.5 6:58 AM
Page 1
1
2
3
OPX/Z
4
X1/Z1
X2/Z2
Instale las pilas.
Brazo del rodillo impresor
MGR
B
REG
A
s
s
A202_Quick Start/A4(N)
03.7.5 6:56 AM
Page 1
1
Installeren van de
kassa
2
Voorbereiding voor de kassa
3
1. Druk de afdrukroller-ontgrendelhendel omhoog om te
ontgrendelen en open de afdrukrollerarm.
Afdrukrollerarm
OPX/Z
MGR
X1/Z1
Verwijderen van de kassa van de
bevestigingsbeugel:
1. Til de voorkant van de kassa op en
trek de kassa naar u toe.
s
s
s 9 @ 1 @ 16 @
sA
B
Voorbeeld: Datum (26 augustus 2003)
PGM
A
26082003
X2/Z2
Afdrukrollerontgrendelhendel
REG
4
Programmeren van
basisonderdelen
5
U kunt nu verkopen
invoeren.
03.7.5 7:02 AM
Page 2
SHARP CORPORATION
Printed in China / Gedruckt in China / Imprimé en Chine / Impreso en China / Gedrukt in China