Hikoki NT1850DE, NT1865DM, NT1865DMA Instruction manual

PDF

Document

Instruction and safety manual
Manuel d’instructions et de s&eacute;curit&eacute;
Instrucciones y manual de seguridad
Model
Mod&egrave;le
Modelo
NT 1865DMA • NT 1865DM
NT 1850DE
NT1865DMA
Cordless Finish Nailer
Cloueur de finition sans fil
Clavadora de acabados a bater&iacute;a
Cordless Brad Nailer
Cloueuse avec clous &agrave; t&ecirc;te
perdue sans fil
Clavadora de brads a bater&iacute;a
NT1865DM
NT1850DE
DANGER
Improper use of this Nailer can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Nailer.
Never allow anyone who has not reviewed this manual.
000Book̲NT1865DMA̲metabo.indb 1
2018/08/06 16:03:20
English
IMPORTANT INFORMATION
Read and understand tool labels and all of the operating instructions, safety precautions and warnings
in this manual before operating or maintaining this nailer.
Failure to follow warnings could result in DEATH or SERIOUS INJURY.
Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic
safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it
occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the
operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by DANGERS and WARNINGS
on the Nailer and in this Manual.
NEVER use this Nailer for applications other than those specified in this Manual.
DEFINITIONS OF SIGNAL WORDS
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
EXPLANATION OF THE NAILING ACTION OF THE metabo HPT NAILER
○ FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull the trigger to drive the fastener. Follow the same sequence to
continue driving fasteners.
○ CONTACT ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull the trigger to drive the fastener.
First, pull the trigger; next, press the push lever against the wood to drive the fastener.
If the trigger is held back, a fastener will be driven each time the push lever is pressed against the wood.
2
000Book̲NT1865DMA̲metabo.indb 2
2018/08/06 16:03:21
English
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
000Book̲NT1865DMA̲metabo.indb 3
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
3
2018/08/06 16:03:21
English
SAFETY — Continued
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5) Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small
metal objects, that can make a connection
from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is
maintained.
– WARNING –
To reduce the risk of injury, user must read
instruction manual.
4
000Book̲NT1865DMA̲metabo.indb 4
2018/08/06 16:03:21
English
SAFETY — Continued
NAILER SAFETY WARNINGS
WARNING
–
–
–
Always assume that the tool contains fasteners.
Careless handling of the nailer can result in
unexpected firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the
fastener causing an injury.
Do not actuate the tool unless the tool is placed
firmly against the workpiece. If the tool is not in
contact with the workpiece, the fastener may be
deflected away from your target.
–
–
–
Disconnect the tool from the power source when
the fastener jams in the tool. While removing a
jammed fastener, the nailer may be accidentally
activated if it is plugged in.
Use caution while removing a jammed fastener.
The mechanism may be under compression and
the fastener may be forcefully discharged while
attempting to free a jammed condition.
Do not use this nailer for fastening electric cables.
It is not designed for electric cable installation and
may damage the insulation of electric cables thereby
causing electric shock or fire hazards.
IMPORTANT SAFETY INSTRUCTIONS FOR USING NAILERS
READ ALL INSTRUCTIONS
DANGER
1. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS.
When operating the Nailer, always wear safety glasses with side shields, and make sure others in work
area wear safety glasses, too.
Safety glasses must conform to the requirements of American National Standards Institute, ANSI Z87.1
and provide protection against flying particles both from the front and side.
The employer must enforce the use of safety glasses by the Nailer operator and others in work area.
WARNING
2. NEVER POINT TOOL AT YOURSELF OR OTHERS
IN WORK AREA.
Always assume the Nailer contains
fasteners.
Never point the Nailer at yourself toward
yourself or others, whether it contains
fasteners or not.
If fasteners are mistakenly driven, it can
lead to severe injuries.
Never engage in horseplay with the
Nailer.
Respect the Nailer as a working
implement.
3. KEEP FINGERS AWAY FROM TRIGGER
WHEN NOT DRIVING FASTENERS TO AVOID
ACCIDENTAL FIRING.
Never carry the Nailer with finger on trigger since
you could drive a fastener unintentionally and injure
yourself or someone else.
Always carry the Nailer by the handle only.
4. CHOICE OF TRIGGERING METHOD IS
IMPORTANT.
Read and understand section titled “Methods of
operation.” (pages 24 - 25)
5
000Book̲NT1865DMA̲metabo.indb 5
2018/08/06 16:03:21
English
SAFETY — Continued
5. ALWAYS WEAR EAR AND HEAD PROTECTION.
Always wear ear protection to protect your ears from
loud noise.
Always wear head protection to protect your head
from flying objects.
6. OPERATE WITHIN PROPER TEMPERATURE
RANGE.
The operating environment for this device is between
32&deg;F (0&deg;C) and 104&deg;F (40&deg;C) so ensure use within this
temperature range.
The device may fail to operate below 32&deg;F (0&deg;C) or
above 104&deg;F (40&deg;C).
7. STORE NAILER PROPERLY, AND BATTERY
REMOVED.
When not in use, the Nailer, battery and battery
charger should be stored in a dry place. Keep out of
reach of children. Lock the storage area.
8. KEEP WORK AREA CLEAN.
Cluttered areas invite injuries. Clear all work areas of
unnecessary tools, debris, furniture, etc.
9. KEEP VISITORS AWAY.
Do not let visitors handle the Nailer.
All visitors should be kept safely away from work
area.
10. DRESS PROPERLY.
Do not wear loose clothing or jewelry as they can be
caught in moving parts.
Rubber gloves and nonskid footwear are
recommended when working outdoors.
Wear protective hair covering to contain long hair.
11. CHECK PUSH LEVER BEFORE USE.
Make sure the push lever operates properly.
(The push lever may be called “Safety”.) Never
use the Nailer unless the push lever is operating
properly, otherwise the Nailer could drive a fastener
unexpectedly. Do not tamper with or remove the push
lever, otherwise the push lever becomes inoperable.
12. KEEP ALL SCREWS AND COVERS TIGHTLY IN
PLACE.
Keep all screws and covers tightly mounted. Check
their condition periodically.
Never use the Nailer if parts are missing or damaged.
13. DO NOT LOAD FASTENERS WITH TRIGGER OR
PUSH LEVER DEPRESSED.
When loading fasteners into the Nailer,
1) do not depress the trigger;
2) do not depress the push lever; and
3) keep the Nailer pointed downward.
14. KEEP FACE, HANDS AND FEET AWAY FROM
FIRING HEAD DURING USE.
Never place your face, hands or feet closer than 8
inches (200 mm) from the firing head.
A serious injury can result if the fasteners are
deflected by the workpiece, or are driven away from
the point of entry.
15. PLACE NAILER PROPERLY ON WORKPIECE.
Do not drive fasteners on top of other fasteners or
with the Nailer at too steep of an angle; the fasteners
can ricochet and hurt someone.
16. BEFORE STARTING WORK, CHECK THE
FASTENING OPERATION SWITCHING DEVICE.
This metabo HPT nailer includes a fastening
operation switching device.
Before starting work, check the setting of the
operation switching device.
If the switching device is not set properly, the nailer
will not operate correctly.
17. BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL.
If the push lever is unintentionally allowed to recontact the workpiece following recoil, an unwanted
fastener will be driven.
In order to avoid this undesirable double fire,
○ Intermittent operation (Trigger firing)
1) Set the switching device to FULL SEQUENTIAL
ACTUATION MECHANISM.
2) Pull the trigger rapidly and firmly.
○ Continuous operation (Push lever firing)
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it recoils
after fastening.
18. DO NOT DRIVE FASTENERS INTO THIN
BOARDS OR NEAR CORNERS AND EDGES OF
WORKPIECE.
The fasteners can be driven through or away from the
workpiece and hit someone.
19. NEVER DRIVE FASTENERS FROM BOTH SIDES
OF A WALL AT THE SAME TIME.
The fasteners can be driven into and through the wall
and hit a person on the opposite side.
20. CHECK FOR LIVE WIRES.
Avoid the risk of severe electrical shock by checking
for live electrical wires that may be hidden by walls,
floors or ceilings. Turn off the breaker switch to
ensure there are no live wires.
21. DO NOT OVERREACH.
Keep proper footing and balance at all times.
6
000Book̲NT1865DMA̲metabo.indb 6
2018/08/06 16:03:21
English
SAFETY — Continued
22. NEVER USE NAILER WHICH IS DEFECTIVE OR
OPERATING ABNORMALLY.
If the Nailer appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange for
repairs by a metabo HPT authorized service center.
23. REMOVE ALL REMAINING FASTENERS AND
BATTERY FROM NAILER WHEN:
1) doing maintenance and inspection;
2) checking proper operation of push lever and
trigger;
3) attaching or removing the nose cap;
4) clearing a jam;
5) it is not in use;
6) leaving work area;
7) moving it to another location; and
8) handing it to another person.
Never attempt to clear a jam or repair the Nailer unless
you have removed battery and all remaining fasteners
from the Nailer.
The Nailer should never be left unattended since people
who are not familiar with the Nailer might handle it and
injure the themselves.
24. REMOVE BATTERY FROM NAILER WHEN:
1) loading fasteners;
2) turning the adjuster.
25. STAY ALERT.
Watch what you are doing. Use common sense.
Do not operate the Nailer when you are tired.
The Nailer should never be used by you if you are
under the influence of alcohol, drugs or medication
that makes you drowsy.
26. HANDLE NAILER CORRECTLY.
Operate the Nailer according to this Manual.
Never allow the Nailer to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
27. NEVER USE NAILER FOR APPLICATIONS OTHER
THAN THOSE SPECIFIED IN THIS MANUAL.
28. HANDLE NAILER CAREFULLY.
Do not drop the Nailer or strike the Nailer against
hard surfaces; and do not scratch or engrave signs
on the Nailer. Handle the Nailer carefully.
29. MAINTAIN NAILER WITH CARE.
Keep the Nailer clean and lubricated for better and
safer performance.
30. USE ONLY PARTS, ACCESSORIES OR
FASTENERS SUPPLIED OR RECOMMENDED BY
metabo HPT.
Unauthorized parts, accessories, or fasteners may
void your warranty and can lead to malfunction and
resulting injuries.
Only service personnel trained by metabo HPT,
distributor or employer shall repair the Nailer.
31. NEVER MODIFY OR ALTER A NAILER.
Doing so may cause it to malfunction and personal
injuries may result.
32. NEVER allow magnets (or similar magnetic
devices) to be adjacent to the nailer, because the
nailer has a magnetic sensor inside.
Doing so will cause a failure or risk of injury by
malfunction.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers.
To avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YFSL.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. To reduce risk of injury, charge metabo HPT
rechargeable battery type BSL18 series. Other type
of batteries may burst causing personal injury and
damage.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress.
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger;
7
000Book̲NT1865DMA̲metabo.indb 7
2018/08/06 16:03:21
English
SAFETY — Continued
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as specified in Table 1.
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes*
AWG Size of Cord
Length of Cord, Feet (Meter)
Equal to or
but less
greater than
than
25 (7.5)
50 (15)
100 (30)
0
2
18
18
18
2
3
18
18
16
3
4
18
18
16
* If the input rating of a battery charger is given in watts
rather than in amperes, the corresponding ampere
rating is to be determined by dividing the wattage rating
by the voltage rating–for example:
8.
9.
10.
11.
1,250 watts
= 10 amperes
125 volts
Do not operate battery charger with damaged cord or
plug-replace them immediately.
Do not operate battery charger if it has received a
sharp blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
Do not disassemble battery charger; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock or fire.
To reduce risk of electric shock, unplug charger from
receptacle before attempting any maintenance or
cleaning. Removing the battery will not reduce this
risk.
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE BATTERY AND
BATTERY CHARGER
You must charge the battery before you can use the power
tool. Before using the model UC18YFSL battery charger,
be sure to read all instructions and cautionary statements
on it, the battery and in this manual.
REMEMBER: USE ONLY metabo HPT BATTERY TYPES
BSL18 SERIES. OTHER TYPES OF BATTERIES MAY
BURST AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
150 (45)
16
14
14
WARNING
Improper use of the battery or battery charger can
lead to serious injury. To avoid these injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is damaged
or is completely worn out. The battery can explode in
a fire.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery charger’s
air vents. Electric shock or damage to the battery
charger may result.
5. NEVER charge outdoors. Keep the battery away
from direct sunlight and use only where there is low
humidity and good ventilation.
6. NEVER charge when the temperature is below 32&deg;F
(0&deg;C) or above 104&deg;F (40&deg;C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for the
battery or the battery charger.
9. NEVER use a booster transformer when charging.
10. NEVER use an engine generator or DC power to
charge.
11. NEVER store the battery or battery charger in places
where the temperature may reach or exceed 104&deg;F
(40&deg;C) such as inside metal box or car.
12. NEVER expose the battery or battery charger to rain
or wet conditions.
13. ALWAYS operate charger on standard household
electrical power (120 volts). Using the charger on any
other voltage may overheat and damage the charger.
14. ALWAYS wait at least 15 minutes between charges to
avoid overheating the charger.
8
000Book̲NT1865DMA̲metabo.indb 8
2018/08/06 16:03:21
English
SAFETY — Continued
15. ALWAYS disconnect the power cord from its
receptacle when the charger is not in use.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the
motor stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○ During work make sure that swarf and dust do not fall
on the battery.
○ Make sure that any swarf and dust falling on the
power tool during work do not collect on the battery.
○ Do not store an unused battery in a location exposed
to swarf and dust.
○ Before storing a battery, remove any swarf and dust
that may adhere to it and do not store it together with
metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject
the battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
specified.
000Book̲NT1865DMA̲metabo.indb 9
7. If the battery charging fails to complete even when a
specified recharging time has elapsed, immediately
stop further recharging.
8. Do not put or subject the battery to high temperatures
or high pressure such as into a microwave oven,
dryer, or high pressure container.
9. Keep away from fire immediately when leakage or
foul odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears
abnormal during use, recharging or storage,
immediately remove it from the equipment or battery
charger, and stop use.
12. Do not immerse the battery or allow any fluids to flow
inside. Conductive liquid ingress, such as water,
can cause damage resulting in fire or explosion.
Store your battery in a cool, dry place, away from
combustible and flammable items. Corrosive gas
atmospheres must be avoided.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the first time, do not use and return it to
your supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of fire. Please observe the
following matters when storing the battery.
○ Do not place electrically conductive cuttings,
nails, steel wire, copper wire or other wire in the
storage case.
○ Either install the battery in the power tool or
store by securely pressing into the battery
cover until the ventilation holes are concealed to
prevent short-circuits.
9
2018/08/06 16:03:21
English
SAFETY — Continued
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please observe
the following precautions.
WARNING
Notify the transporting company that a package
contains a lithium-ion battery, inform the company
of its power output and follow the instructions of the
transportation company when arranging transport.
● Lithium-ion batteries that exceed a power output
of 100 Wh are considered to be in the freight
classification of Dangerous Goods and will
require special application procedures.
● For transportation abroad, you must comply with
international law and the rules and regulations
of the destination country.
EMPLOYER’S RESPONSIBILITIES
1. Ensure that this MANUAL is available to operators
and personnel performing maintenance.
2. Ensure that Nailers are used only when operators and
others in work area are wearing EYE PROTECTOR.
3. Enforce the use of EYE PROTECTOR by operators
and others in work area.
4. Keep Nailers in safe working order.
5. Maintain Nailers properly.
6. Ensure that Nailers which require repair are not
further used before repair.
Power Output
Wh
2 to 3 digit number
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS TOOL!
10
000Book̲NT1865DMA̲metabo.indb 10
2018/08/06 16:03:21
English
OPERATION
NOTE
The information contained in this Manual is designed to assist you in the safe operation of the Nailer.
Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer.
NAME OF PARTS
1. Cordless Finish Nailer
&lt;NT1865DMA&gt;
&lt;NT1865DM&gt;
Handle
Top cover
Lock lever
Battery
Trigger
Hook
Firing head
(outlet)
Push lever
Magazine
Nail feeder (B)
Nail feeder (A)
LED Light
Top cover
Handle
Lock lever
Battery
Trigger
LED Light
Hook
Firing head
(outlet)
Magazine
Nail feeder (B)
Push lever Nail feeder (A)
2. Cordless Brad Nailer
&lt;NT1850DE&gt;
Handle
Top cover
Lock lever
Battery
Trigger
LED Light
Firing head
(outlet)
Hook
Push lever
Stop lever
Magazine
Power
Power indicator switch
Nailing operation
indicator
Battery indicator
Nailing
switch
Battery indicator operation switch
11
000Book̲NT1865DMA̲metabo.indb 11
2018/08/06 16:03:22
English
3
Battery (BSL1830C)
Ventilation holes
Terminals
4. Battery Charger (UC18YFSL)
Cord
Pilot lamp
Battery cover
Latch
Battery
Nameplate
SPECIFICATIONS
1. Cordless Finish Nailer
Model
Motor
Applicable Nail
Applicable Nail Length
Nail Loading capacity [nails]
Firing mode
Cycle rate
[Nails/ second]
Battery
Model
Type
Voltage
Include battery
Weight
Dimension
Height &times; Length &times; Width
NT1865DMA
NT1865DM
DC Brushless
DC Brushless
15 Ga
16 Ga
1-1/4&quot; to 2-1/2&quot; (32 mm - 65 mm)
1&quot; to 2-1/2&quot; (25 mm to 65 mm)
100 (1 strip)
100 (2 strips)
Full sequential / Contact (Selectable) Full sequential / Contact (Selectable)
3.0 (Intermittent)
3.0 (Intermittent)
BSL1830C
Li-ion battery
DC 18V
7.5 lbs. (3.4 kg)
7.3 lbs. (3.3 kg)
13-1/2&quot; &times; 12-5/32&quot; &times; 4-1/2&quot;
12-1/2&quot; &times; 11-3/4&quot; &times; 4-1/4&quot;
(344 mm &times; 309 mm &times; 115 mm)
(315 mm &times; 298 mm &times; 108 mm)
2. Cordless Brad Nailer
Model
Motor
Applicable Nail
Applicable Nail Length
Nail Loading capacity [nails]
Firing mode
Cycle rate
[nails/ second]
Battery
Model
Type
Voltage
Include battery
Weight
Dimension
Height &times; Length &times; Width
NT1850DE
DC Brushless
18 Ga
5/8&quot;-2&quot; (16mm to 50mm)*
100 (1 strip)
Full sequential / Contact (Selectable)
3.0 (Intermittent)
BSL1830C
Li-ion battery
DC 18V
7.3 lbs. (3.3 kg)
12-3/4&quot; &times; 11-3/4&quot; &times; 4-1/4&quot;
(323 mm &times; 298 mm &times; 108 mm)
* Excluding nails that measure 1-3/8&quot; (35 mm)
12
000Book̲NT1865DMA̲metabo.indb 12
2018/08/06 16:03:22
English
3. Battery Charger
Model
UC18YFSL
Input power source
Single phase: AC 120 V 60 Hz
Charging time
Approx. 45 min
(At a temperature of 68&deg;F (20&deg;C))
Charging voltage
DC 14.4 – 18 V
Charging current
DC 3.5 A
Weight
1.1 lbs. (0.5 kg)
NOTE The charging time may vary according to temperature and power source voltage.
NAIL SELECTION
WARNING
● Be sure to use only the genuine metabo HPT
nails for the NT1865DM, NT1865DMA or the
NT1850DE. The use of any other nails can result
in tool malfunction and/or nail breakdown,
leading to serious injuries.
Only nails shown in the Table below can be driven with
this Nailer.
Dimensions of nails
&lt;NT1865DMA&gt;
.12&quot;
(3.0mm)
Min.
Max.
2-1/2&quot; (65mm)
.095&quot; (2.4mm)
.045&quot;
(1.1mm)
1-1/4&quot; (32mm)
15 Gauge finish nails
(Angle: 34&deg;)
.072&quot; (1.8mm)
13
000Book̲NT1865DMA̲metabo.indb 13
2018/08/06 16:03:22
English
&lt;NT1865DM&gt;
Min.
Max.
.065&quot;
(1.65mm)
.055&quot;
(1.4mm)
&lt;NT1850DE&gt;
Min
Max.
.039&quot;
(1mm)
.049&quot;
(1.25mm)
2&quot; (50mm)
.075&quot; (1.9mm)
5/8&quot; (16mm)
.043&quot; (1.1mm)
18 Gauge brad nails
(straight)
2-1/2&quot; (65mm)
.110&quot; (2.8mm)
1&quot; (25mm)
.051&quot; (1.3mm)
16 Gauge finish nails
(straight)
14
000Book̲NT1865DMA̲metabo.indb 14
2018/08/06 16:03:22
English
ACCESSORIES
DANGER
● Accessories other than those shown below
can lead to malfunction and resulting
injuries.
STANDARD ACCESSORIES
3
2
4
1
NT1850DE
NT1865DM
NT1865DMA
(LSRK)
6
1
2
3
4
5
6
7
NT1850DE
NT1865DM
NT1865DMA
(NN)
5
7
Safety glasses....................................................................................... 1
Battery (BSL1830C) .............................................................................. 1
Battery Charger (UC18YFSL)................................................................ 1
Nose cap (mounted on tool) (except NT1850DE) ................................. 1
Nose cap (mounted on tool) (only NT1850DE) ..................................... 1
Battery cover (Code No. 329897) ......................................................... 1
Contractor bag ...................................................................................... 1
1
2
3
1 Safety glasses....................................................................................... 1
2 Nose cap (mounted on tool) (except NT1850DE) ................................. 1
3 Nose cap (mounted on tool) (only NT1850DE) ..................................... 1
15
000Book̲NT1865DMA̲metabo.indb 15
2018/08/06 16:03:22
English
OPTIONAL ACCESSORIES
WARNING
sold separately
○ BATTERY (BSL1830C)
NOTE
Accessories are subject to change without any
obligation on the part of metabo HPT.
APPLICATIONS
&lt;NT1865DMA, NT1865DM&gt;
○ Nailing as finishing process for areas around the
doors, windows as well as edgings.
○ Securing the bottom of drawers. Making various
cases and cabinets.
&lt;NT1850DE&gt;
○ Cabinet and picture frame assembly, furniture trim.
○ On-site and mobile home trim and molding.
REMOVAL AND INSTALLATION
METHOD OF BATTERY
CAUTION
● Be sure keep the fingers away from the trigger
and push lever away from the wood.
○ How to install the battery.
Align the battery with the groove in tool handle and
slip it into place.
Always insert it all the way until it locks in place with a
little click, If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
○ How to remove the battery.
Withdraw battery from the tool handle while pressing
the latch (2 pcs) of the battery.
Handle
Latch
Battery
Push
Insert Pull out
CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure the
following points.
○ The power source voltage is stated on the nameplate.
○ The cord is not damaged.
Do not charge at voltage higher than indicated
on the nameplate.
If charged at voltage higher than indicated on
the nameplate, the charger will burn up.
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charger’s
pilot lamp will blink in red. (At 1-second intervals)
WARNING
Do not use the electrical cord
if damaged. Have it repaired
immediately.
2. Insert the battery to the battery charger.
Insert the battery into the battery charger as shown in
the figure.
Battery
Pilot lamp
Charger
3. Charging
When the battery is connected to the battery charger,
charging will commence and the pilot lamp will light in
red. (See Table 2)
NOTE
If the pilot lamp flikers in red, pull out the plug from
the receptacle and check if the battery is properly
mounted.
When the battery is fully charged, the pilot lamp
will blink in red slowly. (At 1-second intervals)
(See Table 2)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 2, according to the condition of the charger or
the rechargeable battery.
16
000Book̲NT1865DMA̲metabo.indb 16
2018/08/06 16:03:23
English
Pilot lamp
(red)
Before charging
Blinks
While charging
Lights
Table 2
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light
for 0.5 seconds. (off for 0.5 seconds)
Lights continuously
Charging complete Blinks
Lights for 0.5 seconds. Does not light
for 0.5 seconds. (off for 0.5 seconds)
Overheat standby
Lights for 1 second. Does not light for
0.5 seconds. (off for 0.5 seconds)
Blinks
Lights for 0.1 seconds. Does not light
Flickers for 0.1 seconds. (off for 0.1 seconds)
Charging
impossible
(2) Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are
as shown in the Table 3, and batteries that have
become hot should be cooled for a while before being
recharged.
Table 3 Recharging ranges of batteries
Rechargeable
batteries
BSL1830C
Temperatures at which the
battery can be recharged
32&deg;F–104&deg;F
(0&deg;C–40&deg;C)
(3) Regarding recharging time (At 68&deg;F (20&deg;C))
Table 4 Charging time
Charger
Battery
BSL1830C
UC18YFSL
Approx. 45 min.
NOTE
The charging time may vary according to temperature
and power source voltage.
4. Disconnect battery charger from the receptacle.
CAUTION
Do not pull the plug out of the receptacle by
pulling on the cord.
Make sure to grasp the plug when removing from
receptacle to avoid damaging cord.
Battery overheated.
Unable to charge.
(Charging will commence when
battery cools)
Malfunction in the battery or the
charger
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out the
battery from the battery charger.
How to make the batteries perform longer
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the
battery and recharge it after it has cooled for a while.
CAUTION
● When the battery charger has been continuosly
used, the battery charger will be heated, thus
constituting the cause of the failures. Once the
charging has been completed, give 15 minutes
rest until the next charging.
● If the battery is charged while it is heated
because it has been left for a long time in a
location subject to direct sunlight or because
the battery has just been used, the pilot lamp of
the charger lights for 1 second, does not light for
0.5 seconds (off for 0.5 seconds). In such a case,
first let the battery cool, then start charging.
17
000Book̲NT1865DMA̲metabo.indb 17
2018/08/06 16:03:23
English
● When the pilot lamp flikers rapidly in red (at
0.2–second intervals), check for and take out
any foreign objects in the charger’s battery
installation hole. If there are no foreign objects,
it is probable that the battery or charger is
malfunctioning. Take it to your authorized
Service Center.
OFF
Light in green
BEFORE OPERATION
Read section titled “SAFETY” (pages 3 – 10).
Make sure of the followings before operation.
ON
PREPARING THE BATTERY
Read section titled “SAFETY, IMPORTANT SAFETY
INSTRUCTIONS FOR BATTERY CHARGER” (page 7).
You must charge the battery before use.
The charging method of battery is shown in page 16 - 18.
HOW TO OPERATE OPERATION
PANEL
Power Nailing operation
Power indicator switch indicator
Battery indicator
Nailing
switch
Battery indicator operation switch
(1) Power switch ON
Under the condition of “Power switch OFF”, push
and hold on Power switch more than 1 second, then
power indicator lights in Green.
NOTE
● Do not press the push lever and/or pull the trigger
during the process of turning the power switch ON.
Doing so will prevent the power switch from turning
ON.
(2) Power switch OFF
Under the condition of “Power switch ON”, push
and hold on Power switch more than 1 second, then
power indicator goes off.
Under the condition of “Power switch ON”, functions
below are active.
(3) Select Nailing operation mode
(Full sequential actuation / Contact actuation)
After power switch turn ON, always set in Full
sequential actuation mode as initial. (Nailing
operation indicator light in blue.)
Light in blue
To change nailing operation mode, push Nailing
operation switch once. Every pushing, mode will
change between “Full sequential” and “Contact”.
Lighting (Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking (Blue):
CONTACT ACTUATION MECHANISM
Blink in blue
(4) Check Remaining battery level
When pressing the battery indicator switch, the
battery indicator shows Remaining battery level by
status of LED lamp as below.
18
000Book̲NT1865DMA̲metabo.indb 18
2018/08/06 16:03:23
English
Status of indicator
The battery remaining
power is enough.
(6) How to use the LED light
While the power switch on, the LED light will
automatically light up the tip portion of the tool.
Light in green
2 LEDs (Red) light
The battery remaining
power is about half.
1 LED (Red) lights
1 LED (Red) blinks
The battery remaining
power is nearly empty.
Recharge the battery as
soon as possible.
(5) Other functions
In case of operation error, LED lamps show as below.
Status of indicator
Machine is in too cold
(below 23&deg;F (-5&deg;C) or too
hot condition.
Allow the nailer to cool
or warm-up thoroughly in
adequate condition.
LED light
LED light blink in an interval.
• In case of too hot
condition, Blink in
1 second interval.
• In case of too cold
condition, Blink in
0.5 second interval.
After 10 seconds,
automatically turn off LED
light and Power switch.
CAUTION
● Do not expose directly your eye to the light by
looking into the light.
If your eye is continuously exposed to the light,
your eye will be hurt.
● Wipe off any dirt or grime attached to the lens of
the LED light with a soft cloth, being careful not
to scratch the lens.
Scratches on the lens of the LED light can result
in decreased brightness.
TESTING THE NAILER
DANGER
Contact metabo HPT for
inspection
2 LEDs blink in Orange,
after 10 seconds,
automatically turn off
Power switch.
● Operators and others in
work area MUST wear safety
glasses with side shields
which conforms to ANSI Z87.1
specifications.
WARNING
● Make sure the trigger is locked when not
firing nails.
This Nailer has a lock mechanism to prevent the
nails from being fired.
Set the lock lever at the position to lock the
trigger.
Slide the lock lever to the
position when the
Nailer is to be used, and to the position when it
is not in use.
19
000Book̲NT1865DMA̲metabo.indb 19
2018/08/06 16:03:23
English
Trigger
Lock lever
Lock position
(2) Installing the battery.
Do not operate the push lever or trigger while
installing the battery.
Free position
Handle
Latch
● Never use Nailer unless push lever is operating
properly.
The machine employs a preventive mechanism
for unloaded operation.
The machine enters a state where the push lever
cannot be pushed up. This takes place when the
magazine is not loaded with nails or when the
remaining number of nails becomes less than 6 or 9.
CAUTION
● Use caution not to throw the push lever tip onto
wood.
Before actually beginning the nailing work, test the Nailer
by using the checklist below. Conduct the tests in the
following order.
If abnormal operation occurs, stop using the Nailer
and contact a metabo HPT authorized service center
immediately.
Battery
Push
Insert Pull out
(3) Turn on the Power switch.
Power
Power indicator switch
Nailing operation
indicator
Battery indicator
Nailing operation switch
switch
Battery indicator
(1) REMOVE ALL NAILS AND BATTERY FROM
NAILER.
□ ALL SCREWS MUST BE TIGHTENED.
□ THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY with pulling back the nail feeder (B).
(NT1850DE: Unnecessary to pulling back nail
feeder)
Turn on the Power switch by push and hold on Power
switch more than 1 second.
Make sure the power indicator is lighting in green,
and nailing operation indicator is lighting in blue.
(FULL SEQUENTIAL ACTUATION MECHANISM,)
NOTE
● Do not press the push lever and/or pull the trigger
during the process of turning the power switch ON.
Doing so will prevent the power switch from turning
ON.
Trigger
Light in green
Push lever
Light in blue
Nail feeder (B)
20
000Book̲NT1865DMA̲metabo.indb 20
2018/08/06 16:03:24
English
[Auto power off]
When the power is turned on but the Nailer is not
used for 30 minutes, the Nailer is automatically
turned off. To turn on again, press the power
switch.
Pull the trigger
WARNING
Never leave the Nailer with the power on. This
could result in an accident.
Nailing operation indicator
Lighting (Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking (Blue):
CONTACT ACTUATION MECHANISM)
Make sure the battery indicator is not blinking.
If the battery indicator is blinking in red, the battery
doesn’t have enough power and it needs to be
charged.
(4) Remove the finger from the trigger and press the
push lever against the workpiece with pulling back
the nail feeder (B).
□ THE NAILER MUST NOT OPERATE.
Do not pull the
trigger
Pulling back nail
feeder (B)
(6) 1 Without touching the trigger, depress the push
lever against the workpiece with pulling back the
nail feeder (B).
Next, pull the trigger.
□ THE NAILER MUST OPERATE.
2 Hold the trigger back and depress the push
lever against the workpiece again.
□ THE NAILER MUST NOT OPERATE.
3 Separate the finger from the trigger.
Next, 1 is operated again.
□ THE NAILER MUST OPERATE.
(7) Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
Depress
push lever
□ THE NAILER MUST NOT OPERATE.
Pulling back nail
feeder (B)
(5) Separate the push lever from the workpiece.
Next, point the nailer downward, with pulling back the
nail feeder (B), pull the trigger and then wait in that
position for 5 seconds or longer.
(8) Set the nailing operation indicator blinking ON mode.
(CONTACT ACTUATION MECHANISM)
Push the nailing operation switch once, make sure
that the indicator is blinking Blue.
Blink in blue
□ THE NAILER MUST NOT OPERATE.
Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
□ THE NAILER MUST OPERATE.
21
000Book̲NT1865DMA̲metabo.indb 21
2018/08/06 16:03:24
English
(9) If no abnormal operation is observed, you may load
nails in the Nailer.
Drive nails into the workpiece that is the same type to
be used in the actual application.
(3) Push the nail feeder (A) to engage the nail feeder (B)
to the nail strip.
□ THE NAILER MUST OPERATE PROPERLY.
LOADING NAILS
WARNING
● When loading nails into Nailer,
1) remove battery from the nailer;
2) do not pull trigger;
3) do not depress push lever; and
4) keep nailer pointed downward.
&lt;NT1865DMA, NT1865DM&gt;
2–Action Nail Feeding!
(1) Insert nail strip into the back of the magazine.
Nail feeder (B) Nail feeder (A)
NOTE
● Quietly push the nail feeder (A) and nail feeder (B)
against the nail.
If the nail feeder (A) and nail feeder (B) are released
from backward the magazine and bumped against
the nail, the connecting adhesive of the nail can be
damaged.
● Use nail strip of more than 10 nails.
● Use an unbroken nail strip with nails of all the same
length.
The Nailer is now ready to operate.
Magazine
(2) Slide the nail strip forward in the magazine.
Removing the nails:
1 Pull the nail feeder (B) backward.
2 Return the nail feeder (B) forward quietly while
pushing the nail feeder (A).
3 Pull out nails from the back of the magazine.
1
2
Nail feeder (A)
Nail feeder (B)
22
000Book̲NT1865DMA̲metabo.indb 22
Nails
3
2018/08/06 16:03:25
English
&lt;NT1850DE&gt;
(1) Lightly press the stop lever and gently pull out the
magazine cover.
(3) Slide the nail strip into the blade guide.
Press
Pull out
Stop lever
Magazine cover
(2) Set nail strip into the magazine and keep the points of
nails in contact with Groove.
Nail strip
Blade guide
(4) Confirm that nail strip is placed with side guide
grooves and Groove properly, then push the
magazine cover forward to be latched.
NAILER OPERATION
Read section titled “SAFETY” (pages 3 – 10).
DANGER
● Operators and others in
work area MUST wear safety
glasses with side shields
which conforms to ANSI Z87.1
specifications.
Groove
Nails strip Magazine
NOTE
● The nails shown in page 13 - 14 can be loaded onto
the side guide groove of the magazine without any
adjustment.
Always keep the points of nails in contact with
Groove.
Magazine
WARNING
●
●
Side guide
groove
●
Nail
Gap
Groove
●
●
000Book̲NT1865DMA̲metabo.indb 23
● NEVER point tool at yourself
or others in work area.
● Keep fingers AWAY from
trigger when not driving nails
to avoid accidental firing.
Do not use the electrical cord if damaged.
Have it repaired immediately.
Choice of triggering method is important.
Please read and understand “METHODS OF
OPERATION” found below.
Before starting work, check the nailing
operation switching device.
This metabo HPT nailer includes a nailing
operation switching device.
Before starting work, make sure that the
switching device is properly set.
If the switching device is not set properly, the
nailer will not operate correctly.
Never place your face, hands or feet near
firing head when using.
Do not drive nails on top of other nails or
with Nailer at too steep of an angle; nails can
ricochet and hurt someone.
23
2018/08/06 16:03:25
English
● Do not drive nails into thin boards or near
corners and edges of workpiece. Nails can be
driven through or away from workpiece and
hit someone.
● Never drive nails from both sides of a wall
at the same time. Nails can be driven into
and through the wall and hit a person on the
opposite side.
● Never use Nailer which is defective or
operating abnormally.
● Do not use Nailer as hammer.
● Remove all remaining fasteners and battery
from nailer when:
1) doing maintenance and inspection;
2) checking proper operation of push lever
and trigger;
3) attaching or removing the nose cap;
4) cleaning a jam;
5) it is not in use;
6) leaving work area;
7) moving it to another location; and
8) handing it to another person.
● Remove battery from Nailer when:
1) loading nails;
2) turning the adjuster.
This metabo HPT nailer is equipped with a nailer
operation switching device.
Use FULL SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
○ FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next,
pull the trigger to drive the nail.
Follow the same sequence to continue driving nails.
After nailing once, nailing will not be possible again
until remove finger from the trigger and lift the tool off
the wood surface completely.
○ CONTACT ACTUATION MECHANISM:
CONTACT ACTUATION can follow two different
sequences, depending on your use.
To drive several nails:
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
To drive a single nail:
1. Press the push lever against the wood.
2. Pull the trigger to drive the nail.
3. Remove your finger from the trigger and remove
the nailer from the wood.
24
000Book̲NT1865DMA̲metabo.indb 24
The NT1865DMA, NT1865DM employs a preventive
mechanism for unloaded operation.
The NT1865DMA, NT1865DM enters a state where
the push lever cannot be pushed up. This takes place
when the magazine is not loaded with nails or when the
remaining number of nails becomes less than 6 or 9.
CAUTION
● Use caution not to throw the push lever tip onto
wood when the push lever cannot be pushed up.
METHODS OF OPERATION
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with this
Nailer.
They are:
1. Intermittent operation (Trigger fire):
2. Continuous operation (Push lever fire):
(1) Intermittent operation (Trigger fire)
Use the FULL SEQUENTIAL ACTUATION
MECHANISM setting.
WARNING
● For intermittent operation, Set the nailing
operation switch to FULL SEQUENTIAL
ACTUATION MECHANISM (Nailing operation
indicator is light in blue.) (i.e. Set to SINGLE
ACTUATION MECHANISM.)
● To avoid double firing or accidental firing due
to recoil.
1) Set to FULL SEQUENTIAL ACTUATION
MECHANISM.
2) Pull the trigger rapidly and firmly.
1 Set the nailing operation switch to FULL
SEQUENTIAL ACTUATION MECHANISM
(Nailing operation indicator is light in blue.)
(to set to FULL SEQUENTIAL ACTUATION
MECHANISM).
(Set the switching device to the nailing operation
indicator light in blue mode completely as
shown in the diagram. Otherwise, it will be set to
CONTACT ACTUATION MECHANISM.)
2 Position the nail outlet on the workpiece with
finger off the trigger.
3 Depress the push lever firmly until it is completely
depressed.
4 Pull the trigger to drive a nail.
5 Remove finger from the trigger and lift the tool off
the wood surface completely.
To continue nailing in a separate location, move the
nailer along the wood, repeating steps 2 - 5 as
required.
2018/08/06 16:03:25
English
NOTE
Operations 3 and 4 should be done within
2 seconds of each other. If more than 2 seconds
pass after 3, the Nailer will not work properly. If this
happens, retry from 3.
Nailing operation
indicator (Light in blue)
Push lever
Nailing
operation
switch
Trigger
3
NOTE
Operations 2 and 3 should be done within
2 seconds of each other. If more than 2 seconds
pass after 2, the Nailer will not work properly. If this
happens, retry from 2.
Nailing operation
indicator (blink in blue)
Nailing operation
switch
Previously pull the trigger
4
4
2
(2) Continuous operation (Push lever fire)
Using CONTACT ACTUATION MECHANISM
WARNING
● To avoid double firing or accidental firing due
to recoil.
1) Do not press the nailer against the wood
with excessive force.
2) Separate the nailer from the wood as it
recoils after nailing.
1 Set the nailing operation switch to CONTACT
ACTUATION MECHANISM (Nailing operation
indicator is blink in blue.)
(to set to CONTACT ACTUATION MECHANISM).
(Set the switching device to the nailing operation
indicator blink in blue completely as shown in the
diagram. Otherwise, it will not operate properly.)
2 Pull the trigger with the Nailer off the workpiece.
3 Depress the push lever against the workpiece to drive
a nail.
4 Move the Nailer along the workpiece with a bouncing
motion.
Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven,
remove finger from the trigger.
WARNING
● Keep your finger off the trigger except during
nailing operation, because serious injury
could result if the push lever accidentally
contacts you or others in work area.
● Keep hands and body away from the
discharge area. This metabo HPT nailer may
bounce from the recoil of driving a nail and
unwanted subsequent nail may be driven,
possibly causing injury.
NOTE
● If all warnings and instructions are followed,
safe operation is possible with all two systems:
FULL SEQUENTIAL ACTUATION MECHANISM,
CONTACT ACTUATION MECHANISM.
● Always handle nails and package carefully. If nails
are dropped, collating bond may be broken, which
will cause mis-feeding and jamming.
● After nailing:
1) remove battery from the Nailer;
2) remove all nails from the Nailer;
25
000Book̲NT1865DMA̲metabo.indb 25
2018/08/06 16:03:26
English
ADJUSTING THE NAILING DEPTH
To assure that each nail penetrates to the same depth,
be sure that the Nailer is always held firmly against the
workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
1 Remove the battery from the Nailer.
USING THE HOOK
WARNING
● When using the hook, turn off the power
switch (green light “OFF”). Pay sufficient
attention so that the main equipment does
not fall.
If the tool falls, there is a risk of accident.
Hook can be installed on the left or right side. (excluding
NT1865DMA)
(1) Securely hold the main unit and remove the screw
using an allen wrench.
Battery
2 If nails are driven too deep, turn the adjuster to the
shallow side.
Adjustments are in half-turn increments.
2
Too Deep
2
Too Shallow
3
4
5
6
Turn Adjuster
Turn Adjuster
Flush
(2) Remove the hook and hook plate.
Flush
If nails are driven too shallow, turn the adjuster to the
deep side.
Stop turning the adjuster when a suitable position is
reached for a nailing test.
Connect the battery to the Nailer.
ALWAYS WEAR SAFETY GLASSES.
Perform a nailing test.
Remove the battery from the Nailer.
Choose a suitable position for adjuster.
(3) Install the hook on the other side and securely
fasten with screw.
NOTE
Hook can be used as a hanger.
26
000Book̲NT1865DMA̲metabo.indb 26
2018/08/06 16:03:26
English
USING THE NOSE CAP
WARNING
● When attaching or detaching the nose cap,
be sure to remove your finger from the trigger
and remove all remaining fasteners and the
battery from the nailer.
If you like to protect the surface of workpiece against
scratches or markings made by the push lever, attach the
accessory nose cap to the push lever.
1 Remove all remaining fasteners and battery from
nailer.
2 Put the nose cap to the toe of the push lever.
3 The nose cap is marked to indicate the exit point of
the nail, making alignment easier.
4 When not using the nose cap, secure in the storage
compartment located on the reverse side of the
magazine.
Nose Cap Magazine
NT1850DE
NOTE
● The nose cap may reduce nailing depth due to its
thickness. Re-adjustment of nailing depth is required.
CLEARING A JAM
If nails are jammed in firing head, remove it, and adjust the
nailing in the following order.
CAUTION
● Remove the battery from the Nailer.
1 Remove the battery from the Nailer.
2 Remove all nails.
3 Release the Lock lever and open guide plate.
Nose Cap
Lock lever
2
Push Lever
3
Guide Plate
Nose Cap
Magazine
Nose Cap
Magazine
NT1865DM
NT1865DMA
4 Remove the jammed nail with a slotted-head
screwdriver.
CAUTION
● NEVER hit the driver blade.
● NEVER point the tool at yourself or another
person, to avoid risk of injury by mis-firing.
Even if the battery is removed from the nailer,
there is still energy of compressed air remaining
inside.
Push Lever
Nose Cap
27
000Book̲NT1865DMA̲metabo.indb 27
2018/08/06 16:03:26
English
5 Close guide plate and latch.
NOTE
● In case of frequent jam, contact a metabo HPT
authorized service center.
MAINTENANCE
NOTE
The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer.
Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer.
MAINTENANCE AND INSPECTION
&lt;Nailer&gt;
Read section titled “SAFETY” (pages 3 – 10).
WARNING
● Remove battery and all remaining fasteners
from Nailer when:
1) doing maintenance and inspection; and
2) clearing a jam.
3. WARNING LABEL
Change the WARNING LABEL if missing or
damaged.
A new WARNING LABEL is available from a
metabo HPT authorized service center.
Warning label
1. Inspecting the magazine
1 Remove battery.
2 Clean the magazine. Remove dust and wooden chips
which may have accumulated in the magazine.
CAUTION
● Check that the nail feeder slides smoothly by
pulling it with finger.
If not smooth, nails can be driven at an irregular
angle and hurt someone.
2. Storing
○ Do not store the Nailer, and battery in a cold weather
environment.
Keep them in a warm area.
○ When not in use, the Nailer, and battery should be
stored in a warm and dry place.
Keep it out of reach of children.
4. Maintenance chart (See page 29)
5. Operator troubleshooting (See page 29 – 30)
6. Disposal of the exhausted battery
WARNING
Do not dispose of the exhausted battery. The
battery must explode if it is incinerated. The
product that you have purchased contains a
rechargeable battery. The battery is recyclable.
At the end of it’s useful life, under various state
and local laws, it may be illegal to dispose of this
battery into the municipal waste stream. Check
with your local solid waste officials for details
in your area for recycling options or proper
disposal.
28
000Book̲NT1865DMA̲metabo.indb 28
2018/08/06 16:03:27
English
7. Storage
Storing in a place below 104&deg;F (40&deg;C) and out of the
reach of children.
NOTE
Storing lithium-ion batteries
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries
with a low charge may result in performance
deterioration, significantly reducing battery usage
time or rendering the batteries incapable of holding a
charge.
However, significantly reduced battery usage time
may be recovered by repeatedly charging and using
the batteries two to five times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries
dead and purchase new batteries.
CAUTION
In the operation and maintenance of power tools,
the safety regulations and standards prescribed
in each country must be observed.
Important notice on the batteries for the
metabo HPT cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used
with batteries other than these designated by us, or
when the battery is disassembled and modified (such
as disassembly and replacement of cells or other
internal parts).
SERVICE AND REPAIRS
WARNING
● Only service personnel trained by metabo HPT,
distributor or employer shall repair the Nailer.
● Use only parts supplied or recommended by
metabo HPT for repair.
All quality Nailers will eventually require servicing or
replacement of parts because of wear from normal use.
NOTE
Specifications are subject to change without any
obligation on the part of metabo HPT.
Maintenance chart
ACTION
Clean magazine and feeder
mechanism.
Keep push lever working properly.
Prevent a jam.
WHY
HOW
Blow clean daily.
Promote operator safety and efficient Blow clean daily.
Nailer operation.
Operator troubleshooting
Most minor problems can be resolved quickly and easily using the table below.
If problems persist, contact a metabo HPT authorized service center for assistance.
PROBLEM
Power switch doesn’t turn on.
Turn on once, but turn off
automatically.
CHECK METHOD
CORRECTION
Low battery charge.
Charge the battery.
Damaged internal electronics.
Contact metabo HPT for inspection.
Push lever and/or trigger is ON state ? Keep push lever and trigger in OFF
state.
Keep no operation over 30 minutes ? Push and hold power switch more
(Auto-power off function)
than 1 second to switch “ON”
29
000Book̲NT1865DMA̲metabo.indb 29
2018/08/06 16:03:27
English
PROBLEM
Nailer doesn’t operate
(Power switch ON).
Nailer operates, but no nail is driven.
Weak drive.
Slow to cycle.
Drives too deep.
Skipping nails.
Intermittent feed.
Nails jam.
Driven nail is bent.
CHECK METHOD
Nailer not enough pressed against
workpiece.
Trigger not enough pulled.
More than 2 seconds pass from push
lever ON to trigger ON (or trigger ON
to push lever ON).
Preventive mechanism activated.
(No nails, or too few fasteners
remaining) (NT1865DMA /
NT1865DM only)
Lock lever(Trigger lock function) is
“ON” position.
Machine is too cold (below 23&deg;F
(-5&deg;C)) or too hot. (LED light blinks at
regular intervals, and power switch
goes off after 10 seconds.) (Refer to
page 19)
Damaged internal electronics.
Magazine is dirty.
Check for a jam.
Driver blade worn or damaged?
Ribbon spring weakened or
damaged?
Nail feeder damaged?
Check for proper nails.
Check position of nailing depth
adjustment adjuster.
Driver blade worn?
Compressed air pressure has
become low.
Damaged internal electronics.
Check position of nailing depth
adjustment adjuster.
Check for proper nails.
Nail feeder damaged?
Ribbon spring weakened or
damaged?
Driver blade worn or damaged?
Check for proper nails.
Driver blade worn or damaged?
CORRECTION
Hold nailer firmly and press to the
workpiece completely.
Pull the trigger firmly.
Make sure that less than 2 seconds
pass between push lever ON and
trigger ON (or between trigger ON
and push lever ON).
Reload the nails into magazine.
Set Lock lever to “OFF” position.
(Refer to page 19 – 20)
Allow the nailer to cool or warm-up
throughly in adequate condition.
Contact metabo HPT for inspection.
Blow and wipe clean the magazine.
Clear a jam (refer to page 27).
Contact metabo HPT for inspection.
Replace ribbon spring.
Replace nail feeder.
Use only recommended nails.
Readjust according to page 26.
Contact metabo HPT for inspection.
Contact metabo HPT for inspection.
Contact metabo HPT for inspection.
Readjust according to page 26.
Use only recommended nails.
Replace nail feeder.
Replace ribbon spring.
Contact metabo HPT for inspection.
Use only recommended nails.
Contact metabo HPT for inspection.
30
000Book̲NT1865DMA̲metabo.indb 30
2018/08/06 16:03:27
31
000Book̲NT1865DMA̲metabo.indb 31
2018/08/06 16:03:27
SECURITE
AVERTISSEMENTS DE S&Eacute;CURIT&Eacute; G&Eacute;N&Eacute;RAUX CONCERNANT LES OUTILS
&Eacute;LECTRIQUES
AVERTISSEMENT
32
000Book̲NT1865DMA̲metabo.indb 32
2018/08/06 16:03:28
000Book̲NT1865DMA̲metabo.indb 33
2018/08/06 16:03:28
– AVERTISSEMENT –
CONSIGNES DE S&Eacute;CURIT&Eacute; POUR CLOUEUR
AVERTISSEMENT
–
–
–
–
–
–
34
000Book̲NT1865DMA̲metabo.indb 34
2018/08/06 16:03:28
6.
7.
8.
9.
10.
000Book̲NT1865DMA̲metabo.indb 35
2018/08/06 16:03:28
36
000Book̲NT1865DMA̲metabo.indb 36
2018/08/06 16:03:28
000Book̲NT1865DMA̲metabo.indb 37
2018/08/06 16:03:28
11.
38
000Book̲NT1865DMA̲metabo.indb 38
2018/08/06 16:03:28
000Book̲NT1865DMA̲metabo.indb 39
2018/08/06 16:03:28
ATTENTION
Wh
40
000Book̲NT1865DMA̲metabo.indb 40
2018/08/06 16:03:28
CONSERVER CES INSTRUCTIONS
ET
LES METTRE A LA DISPOSITION
DES AUTRES UTILISATEURS
ET
PROPRIETAIRES DE CET OUTIL!
41
000Book̲NT1865DMA̲metabo.indb 41
2018/08/06 16:03:28
Crochet
Crochet
Bras d’arr&ecirc;t
Crochet
42
000Book̲NT1865DMA̲metabo.indb 42
2018/08/06 16:03:28
Rail guide
000Book̲NT1865DMA̲metabo.indb 43
2018/08/06 16:03:29
.12&quot;
(3.0mm)
Min.
Max.
2-1/2&quot; (65mm)
.095&quot; (2.4mm)
.045&quot;
(1.1mm)
1-1/4&quot; (32mm)
.072&quot; (1.8mm)
44
000Book̲NT1865DMA̲metabo.indb 44
2018/08/06 16:03:29
Min.
Max.
.065&quot;
(1.65mm)
.055&quot;
(1.4mm)
&lt;NT1850DE&gt;
Min.
Max.
.039&quot;
(1mm)
.049&quot;
(1.25mm)
2&quot; (50mm)
.075&quot; (1.9mm)
5/8&quot; (16mm)
.043&quot; (1.1mm)
2-1/2&quot; (65mm)
.110&quot; (2.8mm)
1&quot; (25mm)
.051&quot; (1.3mm)
45
000Book̲NT1865DMA̲metabo.indb 45
2018/08/06 16:03:29
ACCESSOIRES STANDARD
3
2
4
1
NT1850DE
NT1865DM
NT1865DMA
(LSRK)
6
1
2
3
4
5
6
7
NT1850DE
NT1865DM
NT1865DMA
(NN)
5
7
1
2
3
46
000Book̲NT1865DMA̲metabo.indb 46
2018/08/06 16:03:29
M&Eacute;THODE DE RETRAIT ET
D’INSTALLATION DE LA BATTERIE
ATTENTION
Batterie
Pousser
AVERTISSEMENT
47
000Book̲NT1865DMA̲metabo.indb 47
2018/08/06 16:03:30
Clignote
Clignote
Clignote
ATTENTION
UC18YFSL
Env. 45 min.
48
000Book̲NT1865DMA̲metabo.indb 48
2018/08/06 16:03:30
ATTENTION
PR&Eacute;PARATION DE LA PILE
000Book̲NT1865DMA̲metabo.indb 49
2018/08/06 16:03:30
50
000Book̲NT1865DMA̲metabo.indb 50
2018/08/06 16:03:30
G&acirc;chette
Levier de
verrouillage
ATTENTION
000Book̲NT1865DMA̲metabo.indb 51
ATTENTION
2018/08/06 16:03:30
Batterie
Pousser
52
000Book̲NT1865DMA̲metabo.indb 52
2018/08/06 16:03:31
□ LE CLOUEUR NE DOIT PAS FONCTIONNER.
la
□ LE
CLOUEUR
CORRECTEMENT.
DOIT
FONCTIONNER
CHARGEMENT DES CLOUS
Le
□ LE CLOUEUR NE DOIT PAS FONCTIONNER.
Magasin
53
000Book̲NT1865DMA̲metabo.indb 53
2018/08/06 16:03:31
3
Clous
Rainure
Recharge Magasin
de clous
54
000Book̲NT1865DMA̲metabo.indb 54
2018/08/06 16:03:31
AVERTISSEMENT
Magasin
●
Clou
●
Ecart
●
●
●
●
●
●
●
●
000Book̲NT1865DMA̲metabo.indb 55
2018/08/06 16:03:32
ATTENTION
METHODES D’UTILISATION
56
000Book̲NT1865DMA̲metabo.indb 56
2018/08/06 16:03:32
G&acirc;chette
4
2
57
000Book̲NT1865DMA̲metabo.indb 57
2018/08/06 16:03:32
R&Eacute;GLAGE DE LA PROFONDEUR DE
CLOUAGE
3
4
5
6
2
Pas assez profond
A ras
58
000Book̲NT1865DMA̲metabo.indb 58
2018/08/06 16:03:32
Chapuchon
de bec
2
&Eacute;LIMINATION D’UN BLOCAGE
ATTENTION
Bras de contact
3
Plque de guldage
Chapuchon Magasin
de bec
NT1865DMA
Chapuchon
Magasin
de bec
000Book̲NT1865DMA̲metabo.indb 59
NT1865DM
59
2018/08/06 16:03:33
ATTENTION
ATTENTION
60
000Book̲NT1865DMA̲metabo.indb 60
2018/08/06 16:03:33
ATTENTION
61
000Book̲NT1865DMA̲metabo.indb 61
2018/08/06 16:03:34
62
000Book̲NT1865DMA̲metabo.indb 62
2018/08/06 16:03:34
63
000Book̲NT1865DMA̲metabo.indb 63
2018/08/06 16:03:34
64
000Book̲NT1865DMA̲metabo.indb 64
2018/08/06 16:03:34
SEGURIDAD
ADVERTENCIAS DE SEGURIDAD GENERAL DE LA HERRAMIENTA EL&Eacute;CTRICA
ADVERTENCIA
000Book̲NT1865DMA̲metabo.indb 65
2018/08/06 16:03:34
66
000Book̲NT1865DMA̲metabo.indb 66
2018/08/06 16:03:34
– ADVERTENCIA –
ADVERTENCIAS DE SEGURIDAD DE LA CLAVADORA
ADVERTENCIA
–
–
–
–
–
–
67
000Book̲NT1865DMA̲metabo.indb 67
2018/08/06 16:03:34
68
000Book̲NT1865DMA̲metabo.indb 68
2018/08/06 16:03:34
000Book̲NT1865DMA̲metabo.indb 69
17.
○
○
18.
19.
20.
21.
22.
23.
2018/08/06 16:03:34
70
000Book̲NT1865DMA̲metabo.indb 70
2018/08/06 16:03:35
8.
9.
10.
11.
000Book̲NT1865DMA̲metabo.indb 71
ADVERTENCIA
2018/08/06 16:03:35
PRECAUCI&Oacute;N
72
000Book̲NT1865DMA̲metabo.indb 72
2018/08/06 16:03:35
Wh
N&uacute;mero de 2 o 3 d&iacute;gitos
&iexcl;GUARDE ESTAS INSTRUCCIONES
Y
P&Oacute;NGALAS A DISPOSICI&Oacute;N DE
OTROS USUARIOS
Y
PROPIETARIOS DE ESTA
HERRAMIENTA!
73
000Book̲NT1865DMA̲metabo.indb 73
2018/08/06 16:03:35
Gatillo
Gatillo
74
000Book̲NT1865DMA̲metabo.indb 74
2018/08/06 16:03:35
Enganche
Bater&iacute;a
000Book̲NT1865DMA̲metabo.indb 75
2018/08/06 16:03:35
.12&quot;
(3.0mm)
Min.
Max.
2-1/2&quot; (65mm)
.095&quot; (2.4mm)
.045&quot;
(1.1mm)
1-1/4&quot; (32mm)
.072&quot; (1.8mm)
76
000Book̲NT1865DMA̲metabo.indb 76
2018/08/06 16:03:35
Min.
Max.
.065&quot;
(1.65mm)
.055&quot;
(1.4mm)
&lt;NT1850DE&gt;
Min.
Max.
.039&quot;
(1mm)
.049&quot;
(1.25mm)
2&quot; (50mm)
.075&quot; (1.9mm)
5/8&quot; (16mm)
.043&quot; (1.1mm)
2-1/2&quot; (65mm)
.110&quot; (2.8mm)
1&quot; (25mm)
.051&quot; (1.3mm)
77
000Book̲NT1865DMA̲metabo.indb 77
2018/08/06 16:03:36
ACCESORIOS EST&Aacute;NDAR
3
2
4
1
NT1850DE
NT1865DM
NT1865DMA
(LSRK)
6
5
7
NT1850DE
NT1865DM
NT1865DMA
(NN)
1
2
3
78
000Book̲NT1865DMA̲metabo.indb 78
2018/08/06 16:03:36
M&Eacute;TODO DE EXTRACCI&Oacute;N E
INSTALACI&Oacute;N DE LA BATER&Iacute;A
PRECAUCI&Oacute;N
ADVERTENCIA
Asidero
Enganche
79
000Book̲NT1865DMA̲metabo.indb 79
2018/08/06 16:03:36
Destello
Iluminaci&oacute;n permanente
Se encender&aacute; durante 0.5 segundos.
No se encender&aacute; durante 0.5 segundos.
(Apagada durante 0.5 segundos)
Se encender&aacute; durante 1 segundo. No
se encender&aacute; durante 0.5 segundos.
(Apagada durante 0.5 segundos)
Se encender&aacute; durante 0.1 segundos.
No se encender&aacute; durante 0.1 segundos.
(Apagada durante 0.1 segundos)
de
del
PRECAUCI&Oacute;N
UC18YFSL
Aprox. 45 min.
80
000Book̲NT1865DMA̲metabo.indb 80
2018/08/06 16:03:36
PRECAUCI&Oacute;N
Luz en verde
ENCENDIDO
PREPARACI&Oacute;N DE LA BATER&Iacute;A
000Book̲NT1865DMA̲metabo.indb 81
2018/08/06 16:03:37
82
000Book̲NT1865DMA̲metabo.indb 82
2018/08/06 16:03:37
PRECAUCI&Oacute;N
PRECAUCI&Oacute;N
83
000Book̲NT1865DMA̲metabo.indb 83
2018/08/06 16:03:37
Gatillo
Alimentador de
clavos (B)
Asidero
Enganche
Bater&iacute;a
Pulsador
Insertar Sacar
000Book̲NT1865DMA̲metabo.indb 84
2018/08/06 16:03:37
No accione el
gatillo
□ EL CLAVADOR NO DEBER&Aacute; FUNCIONAR.
□ EL CLAVADOR DEBER&Aacute;
ADECUADAMENTE.
FUNCIONAR
000Book̲NT1865DMA̲metabo.indb 85
2018/08/06 16:03:37
1
2
Alimentador
Alimentador de de clavos (A)
clavos (B)
3
Clavos
Alimentador
de clavos (B)
Alimentador
de clavos (A)
86
000Book̲NT1865DMA̲metabo.indb 86
2018/08/06 16:03:37
000Book̲NT1865DMA̲metabo.indb 87
2018/08/06 16:03:38
PRECAUCI&Oacute;N
M&Eacute;TODOS DE OPERACI&Oacute;N
88
000Book̲NT1865DMA̲metabo.indb 88
2018/08/06 16:03:38
Gatillo
3
4
Apriete primero el gatillo
4
2
000Book̲NT1865DMA̲metabo.indb 89
89
2018/08/06 16:03:38
AJUSTE DE LA PROFUNDIDAD DE
CLAVADO
2
Poca
profundidad
3
4
5
6
A ras
A ras
90
000Book̲NT1865DMA̲metabo.indb 90
2018/08/06 16:03:38
2
UTILIZACI&Oacute;N DE LA TAPA PARA EL
MORRO
91
000Book̲NT1865DMA̲metabo.indb 91
2018/08/06 16:03:38
PRECAUCI&Oacute;N
PRECAUCI&Oacute;N
PRECAUCI&Oacute;N
92
000Book̲NT1865DMA̲metabo.indb 92
2018/08/06 16:03:39
93
000Book̲NT1865DMA̲metabo.indb 93
2018/08/06 16:03:39
Evitar atascos.
PARA
C&Oacute;MO
Sople diariamente.
94
000Book̲NT1865DMA̲metabo.indb 94
2018/08/06 16:03:39
95
000Book̲NT1865DMA̲metabo.indb 95
2018/08/06 16:03:39
Please contact Koki Holdings America Ltd.
at 1-800-59-TOOLS (toll free), or metabo HPT
AUTHORIZED POWER TOOL SERVICE
CENTER regarding COLLECTION.
Pour le RAMASSAGE,contacter Koki Holdings
America Ltd. au 1-800-59-TOOLS (appel gratuit),
ou UN SERVICE APR&Egrave;S-VENTE D’OUTILS
&Eacute;LECTRIQUE AGR&Eacute;&Eacute; PAR metabo HPT.
Issued by
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo 108-6020, Japan
Distributed by
1111 Broadway Ave,
Braselton, Georgia, 30517
3405 American Drive, Units 9-10,
Mississauga, ON, L4V 1T6
809
Code No. C99719363 G
Printed in China
000Book̲NT1865DMA̲metabo.indb 96
2018/08/06 16:03:40">

Hello! I am an AI chatbot specifically trained to assist you with the Hikoki NT1850DE Instruction manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

It looks like you''ve reached a document that is written in multiple languages, including one that isn''t your native language. You can use the following links to temporarily hide pages without the language you prefer.