LER 2935
5+
grades K+
botley
™
the coding robot
77-piece activity set
Activity Guide
Guía de actividades • Guide d’activités
Spielvorschläge
Introducing Botley™, the Coding Robot
Inserting Batteries
Botley requires (3) three AAA batteries. The Remote
Programmer requires (2) two AAA batteries. Please follow the
directions for battery installation on page 9.
Coding is the language we use to communicate with
computers. When you program Botley using the included
Remote Programmer, you are engaging in a basic form
of “coding.” Beginning with the very basics of sequence
programming is a great way to get started in the world of
coding. So why is learning this so important? Because it
helps teach and encourage:
1. Basic coding concepts
2. Advanced coding concepts like
If/Then logic
3. Critical thinking
4. Spatial concepts
5. Collaboration and teamwork
Note: When the batteries are low on power, Botley will beep
repeatedly and functionality will be limited. Please insert new
batteries.
Getting Started
In CODE mode, each arrow button you press represents a
step in your code. When you transmit your code to Botley,
he will execute all the steps in order. The lights on the
top of Botley will light up at the beginning of each step.
Botley will stop and make a sound when he completes the
code.
Set includes:
• 1 Botley robot
• 1 Remote
Programmer
• Detachable
robot arms
•
•
•
•
•
40 Coding cards
6 Boards
8 Sticks
12 Cubes
2 Cones
•
•
•
•
2 Flags
2 Balls
1 Goal
1 Sticker sheet
STOP Botley from moving at any time by pressing the center
button on top of him.
CLEAR deletes all previously programmed steps. Note that
the Remote Programmer retains code even if Botley is turned
off. Press CLEAR to start a new program.
Botley will power down if left idle for 5 minutes. Press the
center button on top of Botley to wake him up.
Basic Operation
Using the Remote Programmer
Power—Slide this switch
to toggle between OFF,
CODE, and LINEfollowing modes.
You can program Botley using the Remote Programmer.
Press these buttons to enter commands.
POWER
TRANSMIT
Botley moves forward
1 step (approximately 8",
depending on the surface).
Press to send your
code from the Remote
Programmer to Botley.
TURN LEFT
TURN RIGHT
Botley will rotate to
the left 90 degrees.
REVERSE
Botley moves
backward 1 step.
Botley will rotate to
the right 90 degrees.
CLEAR
Press to clear
all previously
programmed steps.
OBJECT DETECTION
Press to enable object
detection.
LOOP
Press to repeat a step
or sequence of steps.
2
STOP
SOUND
Press to toggle between
3 sound settings: High,
Low, and Off.
Start with a simple program. Try this:
1. Slide the POWER switch on the bottom of Botley
to CODE.
2. Place Botley on the floor (he works best on hard
surfaces).
• Check the lighting of your surroundings. Bright light can
affect the way the Remote Programmer works.
• Point the Remote Programmer directly at Botley.
• Bring the Remote Programmer closer to Botley.
Now, try a longer program. Try this:
1. Press CLEAR to delete the old program.
2. Enter the following sequence: FORWARD, FORWARD,
RIGHT, RIGHT, FORWARD.
3. Press TRANSMIT and Botley will execute the program.
Tips:
1. STOP Botley at any time by pressing the center button
on top of him.
2. You can transmit a program from up to 10' away
depending on the lighting (Botley works best in ordinary
room lighting).
3. You can add steps onto a program. Once Botley
completes a program, you can add more steps by
entering them into the Remote Programmer. When you
press TRANSMIT, Botley will restart the program
from the beginning, adding on the additional steps at
the end.
4. Botley can perform sequences of up to 80 steps! If you
enter a programmed sequence that exceeds 80 steps,
you’ll hear a sound indicating the step limit has been
reached.
3. Press the FORWARD arrow on the Remote Programmer.
Loops
4. Point the Remote Programmer at Botley and press the
TRANSMIT button.
Professional programmers and coders try to work as
efficiently as possible. One way to do this is by using LOOPS
to repeat a sequence of steps. Performing a task in the
fewest steps possible is a great way to make your code more
efficient. Every time you press the LOOP button, Botley will
repeat that sequence.
5. Botley will light up, make a sound to indicate the
program has been transmitted, and move forward
one step.
Note: If you hear a negative sound after pressing the transmit
button:
• Press TRANSMIT again. (Do not re-enter your program—
it will remain in the Remote Programmer memory until
you clear it.)
• Check that the POWER button on the bottom of Botley
is in the CODE position.
Try this (in CODE mode):
1. Press CLEAR to delete the old program.
2. Press LOOP, RIGHT, RIGHT, RIGHT, RIGHT, LOOP again
(to repeat the steps).
3. Press TRANSMIT.
Botley will perform two 360s, turning completely around
twice.
3
Now, add a loop in the middle of a program.
Try this:
1. Press CLEAR to delete the old program.
2. Enter the following sequence: FORWARD, LOOP, RIGHT,
LEFT, LOOP, LOOP, REVERSE.
3. Press TRANSMIT and Botley will execute the program.
You can use LOOP as many times as you’d like, as long as you
don’t exceed the maximum number of steps (80).
Object Detection & If/Then Programming
If/Then programming is a way to teach robots how to behave
in certain conditions. We use If/Then behavior and logic all
the time. For example, IF it looks like rain outside, THEN we
might carry an umbrella. Robots can be programmed to use
sensors to interact with the world around them. Botley has an
object detection (OD) sensor that can help him “see” objects
in his path. Using this sensor is a great way to learn about If/
Then programming.
Try this (in CODE mode):
1. Place a cone (or similar object) about 10 inches directly
in front of Botley.
• Is the POWER button on the bottom of Botley in the
CODE position?
• Is the OBJECT DETECTION sensor on (the red light on
the programmer should be lit)?
• Is the object too small?
• Is the object directly in front of Botley?
• Is the lighting too bright? Botley works best in ordinary
room lighting. His performance may be inconsistent in
very bright sunlight.
Note: Botley will not move forward when he “sees” an object.
He’ll just honk until you move the object out of his way.
Black Line Following
Botley has a special sensor underneath him that allows him
to follow a black line. The included boards have a black line
printed on one side. Arrange these in a path for Botley to
follow. Note that any dark pattern or color change will affect
his movements, so be sure there are no other color or surface
changes near the black line. Arrange the boards like this:
2. Press CLEAR to delete the old program.
3. Enter the following sequence: FORWARD, FORWARD,
FORWARD.
4. Press the OBJECT DETECTION
(OD) button. You’ll hear a sound
and the red light on the Remote
Programmer will stay lit to indicate
that the OD sensor is on.
5. Next, enter in what you would like BOTLEY to do if he
“sees” an object in his path—try RIGHT, FORWARD, LEFT.
6. Press TRANSMIT.
Botley will execute the sequence. IF Botley “sees” an object
in his path, THEN he will perform the alternate sequence. He
will then finish the original sequence.
Note: Botley’s OD sensor is between his eyes. He only detects
objects that are directly in front of him and at least 2" tall by
11⁄2" wide. If Botley isn’t “seeing” an object in front of him,
check the following:
4
Start Botley
here
Botley will turn around and go back when he reaches the end
of the line.
Try this:
1. Slide the POWER switch on the bottom of Botley to
LINE.
2. Place Botley on the black line.
The sensor on the bottom of
Botley needs to be directly over
the black line.
3. Press the center button on top
of Botley to start line following.
If he just keeps spinning around,
nudge him closer to the line—he’ll say “Ah-ha” when he
finds the line.
4. Press the center button again to stop Botley—or just
pick him up!
You can also draw your own path for Botley to follow. Use a
white piece of paper and a thick black marker. Hand-drawn
lines must be between 4mm and 10mm wide and solid black
against white.
Detachable Robot Arms
Botley comes equipped with detachable robot arms,
designed to help him perform tasks. Snap the gear onto
Botley’s face, and insert the two robot arms.
Botley can now move objects like the balls and blocks
included in this set. Set up mazes and try to build a code to
direct Botley to move an object from one place to another.
Note: The object detection (OD) feature will not function well
when the detachable robot arms are attached. Please remove
the detachable robot arms when using this feature.
Coding Cards
Use the coding cards to keep track of each step in your
code. Each card features a direction or “step” to program
into Botley. These cards are color-coordinated to match the
buttons on the Remote Programmer.
We recommend lining up the coding cards horizontally in
sequence to mirror each step in your program, and to help
follow and remember the sequence.
Easter Eggs and Hidden Features
Enter these sequences on the Remote Programmer to make
Botley perform secret tricks!
Press CLEAR before trying each one.
1. Forward, Forward, Right, Right, Forward. Then press
Transmit. Botley wants to say “Hi!”
2. Forward, Forward, Forward, Forward, Forward,
Forward (that’s Forward x 6). Then press Transmit.
Botley is having fun now!
3. Right, Right, Right, Right, Left, Left, Left, Left, and
Transmit. Uh-oh, Botley’s a little dizzy.
For even more tips, tricks, and hidden features, please visit
http://learningresources.com/botley.
Troubleshooting
Remote Programmer/Transmitting codes
If you hear a negative sound after pressing the TRANSMIT
button, try the following:
• Check the lighting. Bright light can affect the way the
Remote Programmer works.
• Point the Remote Programmer directly at Botley.
• Bring the Remote Programmer closer to Botley.
• Botley can be programmed a maximum of 80 steps. Be
sure a programmed code is 80 steps or fewer.
• Botley will power down after 5 minutes if left idle. Press
the center button on top of Botley to wake him up. (He’ll
try to get your attention four times before he powers
down.)
• Be sure fresh batteries are inserted properly in both
Botley and the Remote Programmer.
• Check that nothing is obstructing the lens on the
programmer or on top of Botley.
Botley’s moves
If Botley isn’t moving properly, check the following:
• Be sure Botley’s wheels can move freely and nothing is
blocking their movement.
• Botley can move on a variety of surfaces, but works best
on smooth, flat surfaces like wood or flat tile.
• Do not use Botley in sand or water.
• Be sure fresh batteries are inserted properly in both
Botley and the Remote Programmer.
Object Detection
If Botley isn’t detecting objects or working erratically using
this feature, check the following:
• Remove the detachable robot arms before using object
detection.
• If Botley isn’t “seeing” an object, check its size and
shape. Objects should be at least 2" tall and 1½" wide.
• When OD is on, Botley will not move forward when he
“sees” an object—he’ll just stay in place and honk until
you move the object out of his way. Try
5
reprogramming Botley to go around the object.
3. Multiple Turns
Coding Challenges
Start on an orange
board. Program Botley
to “touch” every
board and return to its
starting board.
The coding challenges below are designed to get you familiar with coding
Botley. They are numbered in order of difficulty. The first few challenges are for
beginning coders, while challenges 8–10 will really test your coding skills.
1. Basic Commands
4. Programming Tasks
2. Introducing Turns
Program Botley to move
and deposit the orange
ball in the orange goal.
Start on the BLUE
board. Program
Botley to get to the
GREEN board.
Start on a BLUE board.
Program Botley to get to
the next BLUE board.
5. Programming Tasks
6. There and Back
Program Botley to move
and deposit both the
orange ball and blue
ball in the orange goal.
6
Program Botley to
carry a ball, starting
on the orange board
and returning all the
way back without
dropping it.
7
7. If/Then/Else
8. Nowhere to Run
Battery Information
Using Object Detection,
program Botley to keep
turning around between
the objects.
Program Botley to move
forward 3 steps to get to
the orange board. Then,
use Object Detection to
go around the blocks.
When the batteries are low on power, Botley will beep
repeatedly. Please insert new batteries to continue using
Botley.
Installing or Replacing Batteries
WARNING! To avoid battery leakage, please follow these
instructions carefully.
Failure to follow these instructions can result in battery acid
leakage that may cause burns, personal injury, and property
damage.
Requires: 5 x 1.5V AAA batteries and a Phillips screwdriver
• Batteries should be installed or replaced by an adult.
• Botley requires (3) three AAA batteries. The Remote
Programmer requires (2) two AAA batteries.
• On both Botley and the Remote Programmer, the
battery compartment is located on the back of the unit.
• To install batteries, first undo the screw with a Phillips
screwdriver and remove the battery-compartment door.
Install batteries as indicated inside the compartment.
9. Make a Square
Using the LOOP command, program Botley to
move in a square pattern.
10. Combo Challenge
Using both LOOP and Object
Detection, program Botley to
move from the blue board to
the green board.
• Replace compartment door and secure with screw.
Battery Care and Maintenance Tips
• Use (3) three AAA batteries for Botley and (2) two AAA
batteries for the Remote Programmer.
• Be sure to insert batteries correctly (with adult
supervision) and always follow the toy and battery
manufacturer’s instructions.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel-cadmium) batteries.
• Do not mix new and used batteries.
• Insert battery with the correct polarity. Positive (+)
and negative (-) ends must be inserted in the correct
directions as indicated inside the battery compartment.
• Do not recharge non-rechargeable batteries.
• Only charge rechargeable batteries under adult
supervision.
• Remove rechargeable batteries from the toy before
charging.
• Only use batteries of the same or equivalent type.
• Do not short-circuit the supply terminals.
• Always remove weak or dead batteries from the
product.
• Remove batteries if product will be stored for an
extended period of time.
• Store at room temperature.
• To clean, wipe the surface of the unit with a dry cloth.
• Please retain these instructions for future reference.
8
9
ES
Giro a la izquierda
Encendido
Bucle
Parar
Insertar las pilas
Primeros pasos
10
Bucles
11
12
• No mezcles pilas nuevas y viejas.
INTRODUCIR GIROS
IR Y VOLVER
COMANDOS BÁSICOS
DESAFÍO COMBINADO
FR
•
•
•
•
•
13
Transmettre
Alimentation
14
Stop
3. AVANT, AVANT, AVANT, AVANT, TOURNER À GAUCHE, TOURNER À GAUCHE,
TOURNER À GAUCHE, TOURNER À GAUCHE et Transmettre. Oh, oh ! Le robot Botley
a la tête qui tourne.
Démarrez le robot
Botley ici.
15
DE
•
•
•
•
•
•
•
•
Linkskurve
An/Aus
Stopp
Objekterkennung
Lautstärke
SANS ISSUE
16
17
Programmierkarten
18
19
Learn more about our products
at LearningResources.com
©
Learning Resources, Inc., Vernon Hills, IL, US
Learning Resources Ltd., Bergen Way,
King’s Lynn, Norfolk, PE30 2JG, UK
Please retain the package for future reference.
Made in China.
LRM2935-GUD
Hecho en China.Conserva el envase para
futuras consultas.
Fabriqué en Chine.Veuillez conserver l’emballage.
Hergestellt in China.Bitte Verpackung gut aufbewahren.">
