Sophos RED 10, RED 50 Operating instructions
Sophos RED 50: Secure and reliable connectivity for your branch offices. With advanced features like dual-WAN failover, high-speed LAN ports, and a built-in firewall, the RED 50 ensures uninterrupted internet access and protects your network from threats. Easily manage and monitor your remote locations from a central console. Ideal for small businesses and distributed enterprises seeking a cost-effective and secure networking solution.
Reklam
Reklam
Operating Instructions
Sophos RED Appliances
Sophos RED Appliances
Sophos RED Appliances Operating InstructionsIntroduction
These operating instructions will help you install and configure the Sophos
RED appliances and provide technical specifications of all RED devices.
In addition, please also see the following documents that contain useful
information on safety regulations, regulatory compliance, and configuration
options:
Ì Sophos RED Appliances Security Notes & Regulatory Compliance (part of
the scope of supply)
Ì Sophos RED 10/50 Quick Start Guide (part of the scope of supply
depending on RED model)
Ì Sophos UTM Administration Guide
The instructions must be read carefully prior to using the device and should
be kept in a safe place. You may download all user manuals and additional
documentation from the Sophos Knowledgebase at sophos.com.
RED 10
Scope of supply
Installation
Preliminary steps
Make sure that the RED appliance has been shipped to the branch office.
Ask the person who is going to put the RED appliance into operation at the
branch office to provide the unique RED-ID, which is printed at the bottom
of the device. Note that the RED appliance requires a working Internet
connection at your branch office.
Configuring the RED appliance
Configure the RED appliance in the central UTM appliance as described in
the Sophos UTM Administration Guide.
Sophos RED Quick Start Guide Power supply RJ45 Ethernet cable
Appliance and Security Notes
Security Notes and
Regulatory Compliance
Sophos Access Points
Quick Start Guide
RED 10
December 2012
These operating instructions will help you install and configure the Sophos
RED appliances and provide technical specifications of all RED devices.
In addition, please also see the following documents that contain useful
information on safety regulations, regulatory compliance, and configuration
options:
Ì Sophos RED Appliances Security Notes & Regulatory Compliance (part of
the scope of supply)
Ì Sophos RED 10/50 Quick Start Guide (part of the scope of supply
depending on RED model)
Ì Sophos UTM Administration Guide
The instructions must be read carefully prior to using the device and should
be kept in a safe place. You may download all user manuals and additional
documentation from the Sophos Knowledgebase at sophos.com.
RED 10
Scope of supply
Installation
Preliminary steps
Make sure that the RED appliance has been shipped to the branch office.
Ask the person who is going to put the RED appliance into operation at the
branch office to provide the unique RED-ID, which is printed at the bottom
of the device. Note that the RED appliance requires a working Internet
connection at your branch office.
Configuring the RED appliance
Configure the RED appliance in the central UTM appliance as described in
the Sophos UTM Administration Guide.
Sophos RED Quick Start Guide Power supply RJ45 Ethernet cable
Appliance and Security Notes
Security Notes and
Regulatory Compliance
Sophos Access Points
Quick Start Guide
RED 10
December 2012
Sophos RED Appliances Operating InstructionsConnecting branch office PCs to the RED appliance
At the branch office, use standard Ethernet cables to connect the PCs to
the LAN ports (LAN1-LAN4) of the RED appliance, either directly or via a
network switch.
Use the orange Ethernet cable (from the scope of supply) to connect the
WAN port of the RED appliance to the interface of your router or cable
modem that connects to the Internet.
Connecting the RED appliance to the power supply
Connect the RED appliance to the power supply from the scope of supply.
Plug the power supply into the electrical outlet. The Power LED will light.
After the system has booted, it will connect to the Internet. The status LEDs
System, Router, and Internet will light:
System booted
Router reachable
Internet connectivity up
If all four status LEDs are flashing (from left to right and vice versa), the
device is installing a new firmware version.
Important note: Do not unplug the power while the firmware is updating.
Otherwise the RED appliance will be rendered inoperable and must be
returned to the reseller.
Establishing a tunnel between the branch office and the central
UTM Gateway
The RED appliance will now automatically retrieve its configuration file from
the Internet and establish an encrypted tunnel to the central office. The
Tunnel LED will now light:
Tunnel up
If any of the four status LEDs is not lit or if the System LED is red and
blinking, please refer to "Controls and LED codes" section below to identify
the error.
Controls and LED Codes
Power 1 x 10/100
Base-TX port
1 x USB port
Power
10/100 Base-TX ports
Status signal 4 x 10/100
Base-TX ports
At the branch office, use standard Ethernet cables to connect the PCs to
the LAN ports (LAN1-LAN4) of the RED appliance, either directly or via a
network switch.
Use the orange Ethernet cable (from the scope of supply) to connect the
WAN port of the RED appliance to the interface of your router or cable
modem that connects to the Internet.
Connecting the RED appliance to the power supply
Connect the RED appliance to the power supply from the scope of supply.
Plug the power supply into the electrical outlet. The Power LED will light.
After the system has booted, it will connect to the Internet. The status LEDs
System, Router, and Internet will light:
System booted
Router reachable
Internet connectivity up
If all four status LEDs are flashing (from left to right and vice versa), the
device is installing a new firmware version.
Important note: Do not unplug the power while the firmware is updating.
Otherwise the RED appliance will be rendered inoperable and must be
returned to the reseller.
Establishing a tunnel between the branch office and the central
UTM Gateway
The RED appliance will now automatically retrieve its configuration file from
the Internet and establish an encrypted tunnel to the central office. The
Tunnel LED will now light:
Tunnel up
If any of the four status LEDs is not lit or if the System LED is red and
blinking, please refer to "Controls and LED codes" section below to identify
the error.
Controls and LED Codes
Power 1 x 10/100
Base-TX port
1 x USB port
Power
10/100 Base-TX ports
Status signal 4 x 10/100
Base-TX ports
Sophos RED Appliances Operating InstructionsControls
LEDs
Power
On continuously Power off
Flashing Power on
LAN Connection
On continuously Network connection, no activity
Flashing Network activity
LED codes
LED booting codes
System Router Internet Tunnel Description
The RED device is booting
The RED device has finished booting
The RED device is connecting to
the default gateway/ router
The default gateway/router is reachable
The RED device is connecting
to the Internet
The connection to the Internet
has been established
The RED device is connecting
to the UTM appliance
The connection to the UTM
appliance has been established
The RED device is installing
a new firmware
LED GSM/UMTS failover codes
System Router Internet Tunnel Description
GSM/UMTS failover is active
The default gateway/router is reachable
The connection to the Internet
has been established
The connection to the UTM
appliance has been established
LED error codes
System Router Internet Tunnel Description
DHCP or static address settings failed,
default gateway not reachable
Internet not reachable
No connection to UTM appliance
No configuration or firmware
update failed
off flashing On continuously
LEDs
Power
On continuously Power off
Flashing Power on
LAN Connection
On continuously Network connection, no activity
Flashing Network activity
LED codes
LED booting codes
System Router Internet Tunnel Description
The RED device is booting
The RED device has finished booting
The RED device is connecting to
the default gateway/ router
The default gateway/router is reachable
The RED device is connecting
to the Internet
The connection to the Internet
has been established
The RED device is connecting
to the UTM appliance
The connection to the UTM
appliance has been established
The RED device is installing
a new firmware
LED GSM/UMTS failover codes
System Router Internet Tunnel Description
GSM/UMTS failover is active
The default gateway/router is reachable
The connection to the Internet
has been established
The connection to the UTM
appliance has been established
LED error codes
System Router Internet Tunnel Description
DHCP or static address settings failed,
default gateway not reachable
Internet not reachable
No connection to UTM appliance
No configuration or firmware
update failed
off flashing On continuously
5
6
7
8
9
10
Reklam