Operating instructions
read the EntirE iMpOrtant SaFEty inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
inspect tool before use, looking for damaged, loose, and missing parts. if any problems are found, do not use tool until repaired.
Workpiece and Work area Set up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children or pets to prevent distraction and injury.
2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the air hose to possible damage.
The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be hazardous objects
(such as utility lines or foreign objects) nearby that will present a hazard while working.
Single-Sequential actuation Mechanism Definition
The single-sequential actuation mechanism is designed to allow accurate placement of fasteners.
The tool should only actuate if the Workpiece Contact is pressed against the workpiece prior to pulling the Trigger. It should only actuate again if the trigger is released and squeezed again. The
Tool should not actuate if the Workpiece Contact is not pressed against an object.
Single-Sequential actuation Mechanism testing procedure
tO prEVEnt SEriOuS inJury FrOM acciDEntaL DiScHarGE:
Empty the tool before this procedure. point the tool at a piece of scrap wood when testing.
1. Disconnect the tool from the air supply.
2. Empty the magazine of fasteners.
3. Check that the Trigger and the Workpiece
Contact move freely, without sticking.
6. Hold the tool away, or off of the workpiece.
The Workpiece Contact should return to its original position. Squeeze the Trigger.
the tool must not cycle (actuate).
If it cycles (actuates), stop immediately and take the tool to a qualified service technician.
4. Connect the air supply to the tool and set within the Operating Air Pressure indicated on the Specification chart.
5. Test the tool by pressing the Workpiece Contact against the workpiece without pulling the Trigger.
the tool must not cycle (actuate).
If it cycles (actuates), stop immediately and have it repaired by a qualified service technician.
7. Press the Workpiece Contact against the workpiece and squeeze the Trigger.
the tool must cycle (actuate) only once.
Release the trigger, slide the nailer to a fresh piece of wood, and squeeze it again.
the tool must cycle (actuate) again only once.
With the Trigger depressed, carefully lift the tool and press it against the workpiece again.
the tool must not cycle (actuate).
If it fails to act in the manner explained in bold, have it repaired by a qualified service technician.
Page 12
For technical questions, please call 1-888-866-5797.
Item 64269
Loading the tool
tO prEVEnt SEriOuS inJury FrOM acciDEntaL DiScHarGE, BEFOrE LOaDinG:
• Wear anSi-approved safety goggles with side shields.
Other people in the work area must also wear ANSI-approved impact safety goggles with side shields.
• release the trigger.
• Detach the air supply.
• attempt to discharge the tool into a piece of scrap wood to ensure that it is disconnected and is incapable of driving any fasteners.
1. Depress the Latch (36) and pull back on the Moveable Magazine (43), pulling it out of Fixed Magazine (44).
2. Insert the fasteners into the Moveable Magazine.
If loading staples, fit the crown of the staples so they fit over and ride on the rail of the Magazine.
3. After the nails or staples are loaded, slide the Moveable Magazine back into
Fixed Magazine until the Latch snaps back into place, locking the Moveable Magazine.
note:
The small window gauge on the left side of the Moveable Magazine indicates how many fasteners remain inside Nailer-Stapler.
General Operating instructions
1. Before each use, test the tool as directed in the prior section.
2. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use.
WarninG! tO prEVEnt
SEriOuS inJury: Keep second hand away from tool discharge area, especially if holding workpiece. tool applies extreme force to fastener, and fasteners may deflect or discharge in an unexpected direction.
cautiOn! tO prEVEnt inJury:
Do not hold tool near body while driving. tool recoil can cause injury.
3. Position tool at desired fastener location and depress the Workpiece Contact fully against the workpiece.
Squeeze the trigger to discharge a fastener.
4. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool.
cautiOn! tO prEVEnt inJury
FrOM tOOL FaiLurE:
Do not exceed the tool’s maximum air pressure rating.
If the tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger tool may be required.
5.
after use, to prevent accidents:
a.
release the trigger.
b.
Detach the air supply.
c.
attempt to discharge the tool into a piece of scrap wood to ensure that it is disconnected and is incapable of driving any fasteners.
d.
release the trigger again.
e.
clean external surfaces with clean, dry cloth.
f.
Store indoors out of children’s reach.
Item 64269
For technical questions, please call 1-888-866-5797.
Page 13
user-Maintenance instructions
procedures not specifically explained in this manual must be performed only by a qualified technician.
tO prEVEnt SEriOuS inJury FrOM acciDEntaL DiScHarGE,
BEFOrE any MaintEnancE Or rEpairS arE DOnE (including clearing jams):
• Wear anSi-approved safety goggles with side shields.
Other people in the work area must also wear ANSI-approved impact safety goggles with side shields.
• release the trigger.
• Detach the air supply.
• attempt to discharge the tool into a piece of scrap wood to ensure that it is disconnected and is incapable of driving any fasteners.
• Empty the magazine and leave it open during service. the Magazine is spring-loaded and may cause parts or a fastener to fly out of the tool.
tO prEVEnt SEriOuS inJury FrOM tOOL FaiLurE:
Do not use damaged equipment. if abnormal noise, vibration, or leaking air is detected, have the problem corrected before further use.
tO prEVEnt EXpLOSiOn: Lubricate only with specified lubricants. Lubricate the air inlet using only pneumatic tool oil. Lubricate the internal mechanism using only white lithium grease. Other lubricants may damage the mechanism and may be highly flammable, causing an explosion.
note:
These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air-operated tool.
1.
BEFOrE EacH uSE,
inspect the general condition of the tool. Check for:
• proper workpiece contact operation,
• free workpiece contact and trigger movement,
• loose hardware or housing,
• misalignment or binding of moving parts,
• cracked or broken parts, and
• any other condition that may affect its safe operation.
2.
Daily - air Supply Maintenance:
Every day, perform maintenance on the air supply according to the component manufacturers' instructions. Maintain the lubricator's oil level.
Drain the moisture filter regularly.
Performing routine maintenance on the air supply will allow the tool to operate more safely and will also reduce wear on the tool.
Page 14
For technical questions, please call 1-888-866-5797.
Item 64269
