7.4 Function in 1-channel DMX mode. Varytec LED Pad7 7x10W 6in1 RGBWAUV BL, LED Pad7 7x10W 6in1 RGBAWUV BL, LED Pad7 7x10W 6in1 RGBWAUV WH

Operating

7.4 Function in 1-channel DMX mode

Channel

1

Value

0…255

Function

Colour selection

7.5 Functions in 6-channel DMX mode

4

5

6

2

3

Channel

1

Value

0…255

0…255

0…255

0…255

0…255

0…255

Function

Intensity red (0 % to 100 %)

Intensity green (0 % to 100 %)

Intensity blue (0 % to 100 %)

Intensity white (0 % to 100 %)

Intensity amber (0 % to 100 %)

Intensity UV (0 % to 100 %)

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

41

Operating

7.6 Functions in 7-channel DMX mode

6

7

4

5

2

3

Channel

1

Value

0…255

0…255

0…255

0…255

0…255

0…255

0…255

Function

Intensity (0 % to 100 %)

Intensity red (0 % to 100 %)

Intensity green (0 % to 100 %)

Intensity blue (0 % to 100 %)

Intensity white (0 % to 100 %)

Intensity amber (0 % to 100 %)

Intensity UV (0 % to 100 %)

42

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

Operating

7.7 Functions in 10-channel DMX mode

6

7

4

5

8

2

3

Channel

1

Value

0…255

0…255

0…255

0…255

0…255

0…255

0…255

0…50

51…101

102…152

153…203

Function

Intensity (0 % to 100 %)

Intensity red (0 % to 100 %)

Intensity green (0 % to 100 %)

Intensity blue (0 % to 100 %)

Intensity white (0 % to 100 %)

Intensity amber (0 % to 100 %)

Intensity UV (0 % to 100 %)

No function

Auto mode 1

Auto mode 2

Sound mode 1

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

43

Operating

Channel

9

10

Value

204…255

0…255

0…255

0…9

10…255

Function

Sound mode 2

Automatic show speed, slow to fast, if channel 8 = 51…152

Microphone sensitivity, if channel 8 = 153…255 (0 to 29: microphone off, 30 to 255 = low to high)

No function

Strobe frequency slow to fast

44

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

Technical specifications

8 Technical specifications

Light source

Optical properties

Control

Number of DMX channels

Input connections

Output connections

Power consumption

Supply voltage

Fuse

7 × 6-in1 LEDs (RGBWAUV), each 10 W

Beam angle 25°

DMX, infrared remote control, buttons and display on the device

1, 6, 7 or 10

Power supply

DMX control

Power supply of further devices

DMX control

70 W

IEC chassis plug C14

XLR chassis socket, 3-pin

IEC chassis plug C13

XLR chassis socket, 3-pin

100 – 240 V 50/60 Hz

5 mm × 20 mm, 3.15 A, 250 V, fast-acting

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

45

Technical specifications

Degree of protection

Mounting options

Dimensions (W × H × D)

Weight

Ambient conditions

IP20 hanging

186 × 186 × 128 mm (without bracket)

260 × 260 × 128 mm (incl. bracket)

1.9 kg

Temperature range

Relative humidity

0 °C…40 °C

50 %, non-condensing

46

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

Further information

Construction

Colour mixture

LED type

Base housing

Fanless

Remote control

Wireless DMX

Housing colour

Flat PAR

RGBAWUV x-in-1

Yes

No included

No

Item no. 390703: white

Item no. 428171: black

Technical specifications

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

47

Plug and connection assignments

9 Plug and connection assignments

Introduction

This chapter will help you select the right cables and plugs to connect your valuable equip‐ ment so that a perfect light experience is guaranteed.

Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a short circuit or ‘just’ a not working light show!

DMX connections

The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for the pin assignment of a suitable XLR plug.

2

3

Pin

1

Configuration

Ground, shielding

Signal inverted (DMX–, ‘cold signal’)

Signal (DMX+, ‘hot signal’)

48

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

Troubleshooting

10 Troubleshooting

NOTICE!

Possible data transmission errors

For error-free operation make use of dedicated DMX cables and do not use ordi‐ nary microphone cables.

Never connect the DMX input or output to audio devices such as mixers or ampli‐ fiers.

In the following we list a few common problems that may occur during operation. We give you some suggestions for easy troubleshooting:

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

49

Troubleshooting

Symptom Remedy

The unit does not work, no light Check the mains connection.

Apparently no function despite proper power supply

No response to the DMX con‐ troller

Check if the unit is in DMX mode or in ‘slave’ mode. If so, check the unit in another mode.

1. Check whether the DMX controller is switched on.

Check the DMX connectors and cables for proper con‐ nection.

2. Check the address settings and the DMX polarity.

3. Try using another DMX controller.

4. Check whether the DMX cables run near or parallel to high-voltage cables that may cause damage or interfer‐ ence to a DMX interface circuit.

If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at

www.thomann.de

.

50

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

Cleaning

11 Cleaning

Optical lenses

Fan grids

Clean the optical lenses, that are accessible from the outside, regularly in order to optimize the light output. The frequency of cleaning depends on the operating environment: wet, smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device.

n Clean with a soft cloth using our lamp and lens cleaner (item no. 280122).

n

Always dry the parts carefully.

The fan grids of the device must be cleaned of any contamination, such as dust, etc. on a reg‐ ular basis. Before cleaning, switch off the device and disconnect mains-operated devices from the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly damp lint-free cloth.

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

51

Protecting the environment

12 Protecting the environment

Disposal of the packaging mate‐ rial

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.

Ensure that plastic bags, packaging, etc. are properly disposed of.

Do not just dispose these materials with your normal household waste, but make sure that they are fed to a recovery. Please follow the notes and markings on the packaging.

Disposal of batteries

Batteries must not be disposed of as domestic waste or thrown into fire. Dispose of the bat‐ teries according to national or local regulations regarding hazardous waste. To protect the environment, dispose of empty batteries at your retail store or at appropriate collection sites.

52

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

Disposal of your old device

Protecting the environment

This product is subject to the European Waste Electrical and Electronic Equipment Directive

(WEEE) in its currently valid version. Do not dispose with your normal household waste.

Dispose this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

53

Notes

54

LED Pad 7 7x10W 6in1 RGBWAUV

LED PAR

Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de