- Industrial & lab equipment
- Oxygen Equipment
- Rosemount
- OCX 8800 O2 / Combustibles Transmitter General Purpose
- Owner's manual
Overview. Rosemount OCX 8800 O2 / Combustibles Transmitter General Purpose
Add to My manuals164 Pages
advertisement
Instruction Manual
IM-106-880 Original Issue
February 2005
Section 4 Using the LOI
OCX 8800
OVERVIEW
DISPLAY ORIENTATION
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-1
Display Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-1
LOI Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-2
LOI Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-4
D/A Trim Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-8
This section describes the installation and operation of the LOI module in the
OCX 8800.
The LOI module mounts to a connector on the LOI board. The board is installed on the end of the electronics stack in the electronics housing,
Figure 4-1. There are four mating connectors on the back of the LOI module
that allow the LOI to be oriented as desired by the user.
Figure 4-1. LOI Components
Mounting
Electronics Housing
(Cover Removed)
Electronics Stack
LOI Connector
LOI Board
LOI Module aly tic al
http://www.processanalytic.com
advertisement
Related manuals
advertisement
Table of contents
- 7 Component Checklist
- 7 System Overview
- 15 Specifications
- 20 Mechanical Installation
- 26 Electrical Installation
- 32 Pneumatic Installation
- 38 Initial Startup
- 39 Verify Installation
- 41 Initial Power Up
- 42 Set Test Gas Values
- 42 OCX 8800 Reset Procedure
- 43 Overview
- 43 Display Orientation
- 44 LOI Controls
- 44 Overview
- 44 LOI Key Functions
- 45 LOI Status Codes
- 46 LOI Menu Tree
- 50 D/A Trim Procedures
- 53 Overview
- 53 HART Communicator Signal Connections
- 56 HART Communicator PC Connections
- 57 HART Menu Tree
- 61 D/A Trim Procedures
- 63 Overview
- 63 Fully Automatic Calibration
- 66 Operator - Initiated Autocalibration
- 66 Manual Calibration
- 73 Overview
- 73 OCX 8800 Removal and Installation
- 74 OCX with Remote Electronics
- 80 Repair Sensor Housing
- 80 Sensor Housing Disassembly
- 90 Sensor Housing Assembly
- 100 Repair Electronics Housing
- 100 Electronics Housing Disassembly
- 103 Electronics Housing Assembly
- 106 Replace Tube Fittings
- 106 Remove Tube Fittings
- 107 Install Tube Fittings
- 109 Overview
- 109 Grounding
- 109 Electrical Noise
- 109 Electrostatic Discharge
- 110 Total Power Loss
- 110 Diagnostic Alarms
- 111 Fault Isolation
- 119 Alarm Relay Events
- 122 Sensor Housing
- 126 Electronics Housing
- 129 O2 Cell and Heater Strut Assembly
- 132 Safety Instructions
- 145 Ceramic Fiber Products Material Safety Data Sheet
- 151 High Pressure Gas Cylinders
- 153 Overview
- 153 Description
- 154 Installation
- 154 Setup
- 159 Returning Material