advertisement
I NSTALLATION
2
2.1 U
NPACKING
If the Chemiluminescence (CLD) Analyzer Module is received as a separate unit, carefully examine the shipping carton and contents for signs of damage. Immediately notify the shipping carrier if the carton or contents is damaged. Retain the carton and packing material until all components associated with the CLD Analyzer Module are operational.
2.2 A
SSEMBLY
If the CLD Analyzer Module requires assembly with other components (e.g., the Platform and associated I/O Modules), do so at this time. Following the guides on the bottom left and bottom center of the Platform, carefully slide the Analyzer Module halfway into place.
CAUTION: HAND INJURY HAZARD
Do not place hands or fingers in the Platform front handles when front panel is open. Dropping the front panel of the Platform while hand or fingers are inside either handle can cause serious injury.
Lift the spring-loaded pins on the front of the Analyzer Module, and carefully slide it the rest of the distance. Secure the module in position by releasing the pins, which seat in the available holes in the bottom of the case (see Figure 2-1). If the module and Platform are difficult to assemble, remove the module, ensure the top cover of the module is firmly seated on the hold-down screws, and repeat the assembly procedure.
Refer to Section 2-4 for electrical connections.
Install I/O Module(s) according to guidelines in the I/O manual. After startup and calibration have been performed, secure the front panel with the six screws provided.
2.3 L
OCATION
Install the CLD Analyzer Module in a clean, weather-protected, vibration-free location free from extreme temperature variations and moisture. For best results, install the instrument near the sample stream to minimize sample transport time.
The analyzer should be installed within
±
15
°
of horizontal.
748410-A
August 1999
Chemiluminescense Detector Analyzer Module
Rosemount Analytical NGA 2000
5
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Purpose/Safety Summary
- 13 Specifications - General
- 13 Specifications - Physical
- 14 Specifications - Sample
- 14 Specifications - Gas Connections
- 15 Customer Service, Technical Assistance and Field Service
- 15 Returning Parts to the Factory
- 16 Documentation
- 16 Compliances
- 17 1.1 Overview
- 17 1.2 Typical Applications
- 17 1.3 Theory of Technology
- 18 1.4 Features
- 21 2.1 Unpacking
- 21 2.2 Assembly
- 21 2.3 Location
- 22 2.4.1 Overview
- 22 2.4.2 Connections
- 24 2.4.3 Specifications
- 25 2.5 Electrical Connections
- 29 3.1 OVERVIEW
- 29 3.2 Displays
- 29 3.2.1 Run Mode Display
- 29 3.2.2 Menu Displays
- 30 3.2.3 Help Displays
- 30 3.3 Startup Procedure
- 31 3.4 Binding
- 33 3.5 Calibration
- 34 3.6 Converter Temperature Adjustment Procedure
- 36 3.7 Measurement of Converter Efficiency
- 36 3.7.1 Test Setup for Measurement of Conversion Efficiency
- 36 3.7.2 Test Procedure
- 38 3.7.3 Subnormal Conversion Efficiency
- 40 3.7.4 Replacement of Converter
- 40 3.7.5 Capillaries
- 40 3.7.6 TEA Scrubber
- 41 3.8 Routine Operation
- 43 4.1 Overview
- 45 4.4 Converter
- 46 4.5 Ozonator
- 46 4.6 Printed Circuit Boards
- 46 4.7 Detector Disassembly
- 51 5.1 Replacement Parts