Fisher ROC Serial Driver Help

Index

'

'<Device Name>' - Failed to read EFM pointer file. <Extended Error> 26

'<Device Name>' - Failed to write EFM pointer file. <Extended Error> 26

A

Address '<address>' is out of range for the specified device or register 21

Address Descriptions 15

Address Specification 8

Address Validation 21

Automatic Tag Database Generation 14

Automatic Tag Database Generation Error Messages 22

B

Bit Assignments 19

Block read for point type '<point type>', logical address '<logical address>', parameter range

'<start parameter - end parameter>' of device '<device name>' failed. Parameters are not

in the loaded UDP configuration 33

Block read for point type <point type>, logical address <logical address>, parameter range

<start parameter - end parameter> of device <device name> failed. <Error Reason> 27

C

Channel Setup 6

Communications error on '<channel name>' [<error mask>] 31

COMn does not exist 32

COMn is in use by another application 32

D

Data Type <type>' is not valid for device address '<address>' 22

www. kepware.com

36

37

Fisher ROC Serial Driver Help

Data Types Description 13

Device '<device>' responded with error. (Tag '<tag address>') - Details: '<error code>' 27

Device address '<address>' contains a syntax error 22

Device address '<address>' is not supported by model '<model name>' 22

Device address '<address>' is Read Only 22

Device name '<device name>' is not responding 30

Device Setup 7

Device Specific Messages 26

Device Status Messages 30

E

EFM '<type>' upload failed for device '<device>'. <Reason> 31

EFM Meters 10

Error Descriptions 20

Error importing CSV tag record <record number>: Address '<Address>' is out of range for the

specified device or register 23

Error opening COMn 32

Error Reasons 21

F

Failed to obtain data block for PointType = <point type>, Logical Address = <address>,

Starting Parameter = <starting parameter>, Ending Parameter <ending parameter> for

device '<device>'. Error = <ROC error code> 27

Failed to write data for PointType = '<point type>', Logical Address = '<address>',

Parameter = '<parameter>' for device '<device>'. Error = '<error code>' 28

H

Help Contents 5

M

Missing address 22

www. kepware.com

Fisher ROC Serial Driver Help

O

Operator Identification 9

Operator identification failed for device '<device name>'. <Error Reason> 28

Overview 5

P

Point Number Details 18

R

Read for point type '<point type>', logical address '<logical address>', parameter number

'<parameter>' of device '<device name>' failed. Parameter is not in the loaded UDP

configuration 33

Read for point type <point type>, logical address <logical address>, parameter number

<parameter number> of device <device name> failed. <Error Reason> 28

Resetting the EFM cache for device '<device>' 31

ROC Error Codes 34

ROC initialization error: Unable to read general configuration 28

ROC initialization error: Unable to retrieve I/O map 29

ROC Point Types 15

S

Serial Communications 31

Serialization of EFM data to temporary file '<file name>' failed. Reason: '<file I/O error>' 29

T

Tag Import Settings 7

The username or password supplied was not accepted. Error = 6 29

The username or password supplied was not accepted. Error = 63 29

Time synchronization with device '<device name>' failed. <Error Reason> 30

www. kepware.com

38

39

Fisher ROC Serial Driver Help

U

Unable to generate a tag database for device '<device>'. Reason: <Error Reason> 23

Unable to generate a tag database for device '<device>'. Reason: Auto tag generation failed.

Device is not responding 23

Unable to generate a tag database for device '<device>'. Reason: Error while reading from

import file 24

Unable to generate a tag database for device '<device>'. Reason: Error while reading from

ROC system file 24

Unable to generate a tag database for device '<device>'. Reason: Failed to open recordset 24

Unable to generate a tag database for device '<device>'. Reason: Import file <file name> not

found 24

Unable to generate a tag database for device '<device>'. Reason: Input file is corrupt 24

Unable to generate a tag database for device '<device>'. Reason: Input file not found 25

Unable to generate a tag database for device '<device>'. Reason: Low memory resources 25

Unable to generate a tag database for device '<device>'. Reason: ROC system file <file name>

not found 25

Unable to generate a tag database for device '<device>'. Reason: System DB file <file name>

not found 25

Unable to load User-Defined Point configuration for point type <point type>, logical address

<logical address>, parameter number <parameter> of device <device name>. The

number of parameters for this point is 0 33

Unable to parse the User-Defined Point configuration information for point type '<point type>'

on device '<device name>' 33

Unable to set comm parameters on COMn 32

User-Defined Point Configuration upload for point type '<point type>', logical address

'<logical address>', parameter number '<parameter>' of device '<device name>' failed.

<Error Reason> 33

User-Defined Point Error Messages 32

User-Defined Point Types 18

W

Write for the following tags of device <device name> failed: <tag list>. <Error Reason> 30

Write request rejected on Read Only item reference '<channel name>' '<device name>'

'<address>' 30

www. kepware.com