- Home
- Domestic appliances
- Climate control
- Fireplaces
- Dragon Wholesaling
- 864 TRV GSR2
- Installation manual
advertisement
Installation
(for qualified installers only)
Diffuser Plate Adjustment
Certain vent configurations require the diffuser plate to be adjusted (refer to the approved vent configuration charts for details). Position # 1 is stock (bent). Position # 2 is flattened. See the directions below to change the diffuser to position #2.
Firebox Roof
23
Back Wall of Firebox
Remove the exhaust restrictor.
1/4" (6mm) Nutdriver
1/4" (6mm) Nutdriver
Remove the diffuser.
DIFFUSER SIDE VIEW
Before (Stock - Position # 1)
Bend the round portion of the diffuser so it is flat (position # 2).
After (Position # 2)
Secure the flattened diffuser plate with the screws removed earlier.
© Travis Industries 4141013
Replace the exhaust restrictor (see “Exhaust
Restrictor Adjustment” for restrictor settings).
100-01389
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Overview
- 6 Installation Options
- 6 Heating Specifications
- 6 Dimensions
- 7 Packing List
- 7 Additional Items Required
- 7 Installation Overview
- 7 Recommended Installation Procedure
- 8 Top Vent or Rear Vent Configuration
- 8 Converting the Fireplace to Top Vent Configuration
- 9 Converting the Fireplace to Top Vent (continued)
- 10 Fireplace Placement Requirements
- 10 Clearances
- 10 Raised Fireplaces
- 11 Configuration
- 13 Nailing Brackets
- 14 Corner Installations - Rear Vent Configuration
- 15 Corner Installations - Top Vent Configuration
- 16 Gas Line Requirements
- 16 Gas Line Connection
- 16 Gas Inlet Pressure
- 17 Gas Line Location
- 17 Converting Gas Line to the Left Side
- 18 Electrical Connection (required)
- 19 Vent Requirements
- 19 Vent Clearances
- 19 Altitude Considerations
- 20 Approved Vent
- 20 Vent Installation
- 21 Approved Vent Configurations
- 21 Restrictor Position
- 21 Exhaust Restrictor Adjustment
- 22 Intake Restrictor Adjustment
- 23 Diffuser Plate Adjustment
- 24 Termination (no vertical rise)
- 25 Termination (with vertical rise)
- 26 Termination
- 29 Termination Requirements
- 30 Hearth Requirements
- 31 Facing Requirements
- 31 Drywall Installation
- 32 Facing Overview
- 32 Optional Faceplates
- 33 combustible under 1" (25mm) thick)
- 34 thick) - Side View
- 35 combustible over 1" (25mm) thick)
- 36 Faces
- 37 Thick Facing Installation - Side View
- 38 Mantel Requirements
- 38 Combustible Mantels
- 38 Examples
- 38 Non-Combustible Mantels
- 39 with Hor. Termination
- 40 Termination
- 41 Steps for Finalizing the Installation
- 42 Air Shutter Adjustment
- 43 Barrier Removal
- 44 Glass Frame Removal and Installation
- 45 (continued)
- 46 Log Set Installation
- 46 Log Set Overview
- 47 Back Log
- 47 Right Log
- 48 Front Left Log
- 48 Left Log
- 49 Center Twig
- 49 Front Ember Chunk
- 50 Left Twig
- 50 Center Left Twig
- 51 Center Log
- 51 Right Twig
- 52 Ember Installation
- 52 Rock Wool Placement
- 53 LP Conversion Instructions
- 56 Fireback Installation
- 57 Grill Installation
- 58 Wiring Diagram
- 60 Index