advertisement
MAINTENANCE
Replacing Lamp Unit
CAUTION:
• Do not touch the lamp and the lamp unit carelessly. It is extremely hot. Wait at least one hour for the lamp to cool down before handling.
• Do not loosen any screws except for those mentioned below.
• The lamp may break if handled improperly.
• Do not use other than a Marantz replacement lamp unit.
❖
How to replace the Lamp Unit
PREPARATION:
When replacing the lamp, turn off the power for the projector. After the cooling fan stops, disconnect the power cord and wait for one hour until the lamp is cooled down completely, then replace the lamp.
1.
Press the STANDBY key on the remote controller or the
POWER key on the projector to turn the projector off.
5.
Remove the lamp cover screw.
2.
After the cooling fan stops, Unplug the AC power cord.
6.
Remove the lamp cover in the direction of the arrow.
Lamp cover
3.
Wait at the least one hour for the lamp and lamp unit to cool down.
4.
Read the caution and warning labels on the unit.
Lamp cover
7.
Remove the two screws of the lamp unit. At this time, do not remove the other screws.
WARNING
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
CAUTION : HIGH PRESSURE LAMP
MAY EXPLODED IF IMPROPERLY HANDLED.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
CAUTION HOT : UNPLUG
THE POWER CORD AND WAIT
60 MINUTES BEFORE CHARGING
THE LAMP.
ATTENTION CHAUD :
DEBRANCER LE CORD ON
MODEL NO. VP-16S1 / U1M
AC 120V 60HZ 2.0A
SERIAL NO.
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
WARNING
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
CAUTION :
HIGH PRESSURE LAMP
MAY EXPLODED IF IMPROPERLY HANDLED.
CAUTION HOT :
UNPLUG
THE POWER CORD AND WAIT
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
60 MINUTES BEFORE CHARGING
THE LAMP.
ATTENTION :
LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
ATTENTION CHAUD :
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
AC 120V 60H Z 2.0W
SERIAL NO.
MADE IN JAPAN
FABRIQUE AU JAPON
30
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 IMPORTANT SAFEGUARDS
- 5 Caution Concerning the Lamp Replacement
- 5 Caution Concerning the Lamp Unit
- 5 Cautions Concerning the Setup of the Projector
- 5 Notes on Operation
- 6 FEATURES
- 7 ACCESSORIES
- 8 PROJECTOR LAYOUT AND FUNCTIONAL OVERVIEW
- 8 Front and Top View
- 9 Rear and Terminals View
- 9 Bottom View
- 10 Remote Controller
- 11 Preparing the Remote Controller
- 11 Remote Controller Operational Range
- 12 CONNECTION
- 12 Connection with AC Power Supply
- 12 Connection with Video Equipments
- 13 Connection with a HD-Video, Satellite, Cable Tuner or PC
- 13 Advanced Connection
- 14 INITIAL SETTING
- 14 Turning on the Power
- 14 Zooming and Focusing
- 14 Adjusting the Image Position
- 15 Adjusting the Height
- 15 Detail Focusing
- 16 Keystone Correction
- 17 INSTALLATION
- 17 Recommended Setting
- 18 Screen Size and Projection Distance (inch)
- 19 Screen Size and Projection Distance (m)
- 20 BASIC OPERATIONS
- 20 Turning on the Power
- 20 Selecting the Input Signal Source
- 20 Selecting the Aspect Mode
- 21 The Screen Images in a 16:9 screen
- 22 The Screen Images in a 4:3 screen
- 23 To Turn off the Power
- 24 OPERATIONS
- 24 Menu Structure
- 25 Using On-Screen Menu
- 25 Picture Adjust
- 26 Fine Menu
- 28 Setting
- 29 Display
- 30 Configuration
- 31 Trigger
- 32 Memory
- 32 Lamp Life and Replace Lamp
- 34 MAINTENANCE
- 34 Replacing Lamp Unit
- 35 Cleaning the Lens
- 35 Replacement Parts
- 35 Optional Accessories
- 36 TROUBLESHOOTING
- 36 ERROR MODE
- 37 ON SCREEN MESSAGE
- 37 SPECIFICATIONS
- 38 GLOSSARY
- 39 DIMENSIONS