- Computers & electronics
- Computer components
- System components
- Internal hard drives
- Seagate
- ST3500641AS-AN
- Data Sheet
advertisement
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab.
• EUT name (model numbers): See table below
• Certificate numbers:
Model
ST3500841A, ST3500641A, ST3400833A, ST3400633A, ST3300822A
ST3300622A, ST3250824A, ST3250624A, ST3200827A, ST3160812A
ST3160212A, ST3120814A, ST3120213A, ST3802110A, ST3402111A
Certificate Number
E-H011-05-3453 (B)
• Trade name or applicant: Seagate Technology
• Manufacturing date: September 2005
• Manufacturer/nationality: Singapore and China
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).
2.13.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.
30 Barracuda 7200.9 PATA Product Manual, Rev. C
advertisement
Key Features
- 500 GB 3.5" 7200 RPM Serial ATA II
- Storage drive buffer size: 16 MB
- 690 g
Related manuals
advertisement
Table of contents
- 9 Introduction
- 11 Drive specifications
- 11 Specification summary table
- 26 Formatted capacity
- 26 LBA mode
- 26 Default logical geometry
- 27 Recording and interface technology
- 28 Physical characteristics
- 28 Seek time
- 28 Start/stop times
- 29 Power specifications
- 29 Power consumption
- 32 Conducted noise
- 32 Voltage tolerance
- 32 Power-management modes
- 33 Environmental specifications
- 33 Ambient temperature
- 33 Temperature gradient
- 33 Humidity
- 33 Altitude
- 34 Shock
- 34 Vibration
- 35 Acoustics
- 36 Electromagnetic immunity
- 37 Reliability
- 37 Agency certification
- 37 Safety certification
- 37 Electromagnetic compatibility
- 38 FCC verification
- 39 Environmental protection
- 39 European Union Restriction of Hazardous Substances (RoHS)
- 39 Corrosive environment
- 41 Configuring and mounting the drive
- 41 Handling and static discharge precautions
- 42 Breather filter hole precautions
- 43 Jumper settings
- 43 Master/slave configuration
- 43 Cable-select option
- 43 Alternate capacity jumper
- 44 Ultra ATA/100 cable
- 44 Drive mounting
- 47 ATA interface
- 47 ATA interface signals and connector pins
- 48 Supported ATA commands
- 50 Identify Device command
- 54 Set Features command
- 55 S.M.A.R.T. commands
- 57 Seagate Technology support services