advertisement
![Maintenance. Haul-Master 69377, Item 69377, Drywall Panel Hoist | Manualzz Maintenance. Haul-Master 69377, Item 69377, Drywall Panel Hoist | Manualzz](http://s1.manualzz.com/store/data/003203140_1-dfc3714745ccc2c2cde32a24f1ac8299-360x466.png)
cleaning, Maintenance, and lubrication
procedures not specifically explained in this manual must be performed only by a qualified technician.
tO preVent SeriOUS inJUry FrOM tOOl FailUre:
Do not use damaged equipment. if abnormal noise or vibration occurs, have the problem corrected before further use.
caUtiOn! to prevent injury:
Wear anSi-approved safety goggles and heavy-duty leather work gloves during inspection and maintenance, especially near the wire rope.
1. beFOre eacH USe, inspect the general condition of the tool. Check for loose screws, wire rope fraying and other wire rope wear, misalignment or binding of moving parts, cracked or broken parts and any other condition that may affect its safe operation.
WarninG! A Wire Rope breaking while under load can cause serious personal injury and property damage. Broken Wire Rope strands are sharp and can cause puncture injuries.
2. Inspect the tool before beginning work each day.
Have the Wire Rope replaced immediately as soon as wear is detected.
WarninG! Do not lubricate any part of the
Winch components. The Brake is friction based and may fail if lubricated.
3. Occasionally oil the Caster Wheel bearings.
4. If the telescoping sections do not slide freely, apply paraffin wax or candle wax to the sides as a lubricant.
Wire rope Safety information
1. Since the safe operation of this Hoist depends on safe maintenance of the steel Wire Rope, it is important that you carefully monitor and maintain the included Wire Rope. Have the Wire
Rope replaced by a qualified technician as soon as it has any fault, defect or noticeable wear.
2. The American Society of Mechanical Engineers lists standards for the safe use of wire rope in its standard numbered ASME B30 19-2000.
This standard is available to the public, and we strongly suggest you become familiar with it.
3. The following does not replace the information found in ASME B30 19-2000, but paraphrases some of the important information contained therein.
a. Inspection should be made at least once every work day. Inspector should look for damage to the wire rope, such as crushing, kinking, broken strands, corrosion etc. Particular attention should be paid to undue wear and stress points, such as near pulleys, crimped ends, hooks, etc.
b. Wire ropes should be taken out of service if discovered to be damaged, and must be replaced before resuming use of the affected tool.
4. The wire rope must be replaced with one of identical diameter and construction. The wire rope provided with this Hoist is suited to the purpose, and any replacement must be at least to the original standard.
Page 12 For technical questions, please call 1-888-866-5797.
Item 69377
pleaSe reaD tHe FOllOWinG careFUlly
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Item 69377 For technical questions, please call 1-888-866-5797.
Page 13
advertisement
Related manuals
advertisement
Table of contents
- 3 Safety
- 4 Specifications
- 4 Assembly
- 8 Operation
- 12 Maintenance
- 14 Parts List and Diagram
- 16 Warranty