advertisement
Operation flow
The operation flow of the recorder is as follows.
z x c v b n m
,
.
Rack mounting
Connections
Startup
Install the HDD units
Network settings of the recorder
Network settings of a PC
Formatting of the hard disk drives
Network settings of the camera
Setup
Install the recorder in the rack. (Refer to the installation guide.)
Go to step 2 when not installing it in the rack.
Connect the recorder to each device. (Refer to the installation guide.)
Turn on the power of the recorder. (Refer to the installation guide.)
When using extension units, turn the power of all the extension units before turning on the power of the recorder.
Install hard disk drives in the recorder. (Refer to the installation guide.)
When unformatted hard disk drives are installed, they will automatically be formatted.
According to your needs, determine the operational mode.
Operate the buttons on the front panel of the recorder to configure the network settings of the recorder. (Page 11)
Change the TCP/IP setting of the PC to conform to the settings of the recorder. (Page 13)
Display the disk configuration menu and format the hard disk drives. (Page 89)
Display the camera setup menu and configure the network settings of the cameras. (Page 49)
Perform the required settings on the setup menu to start operation. (Page 8)
⁄0
Start operation
When necessary
Replacement of the hard disk drives
It is possible to replace the hard disk drives without turning off the power of the recorder. (Refer to the Installation guide.)
7
8
Setup menu and its items
It is necessary to configure the settings on the setup menu in advance to use the recorder. The setup menu will be displayed by clicking the [Setup] button.
Setup items Description
Reference page
Quick
Setup
Basic
Basic
Displays the "Quick" page that contains the minimum required settings to be configured to operate the recorder.
26
31 Settings for the basic operations of the recorder can be configured.
Current time and date can be set.
32 Time & date
Emergency rec.
Emergency rec.
Event
Basic
Terminal alarm
Site alarm
Command alarm
Schedule
Time table
Program
Special days
Settings relating to emergency recording such as the recording time and recording rate can be configured.
Basic settings relating to the event actions can be configured.
Event actions to be taken at a terminal alarm occurrence can be set.
Event actions to be taken at a site alarm occurrence can be set.
Event actions to be taken at a command alarm occurrence can be set.
Create timetables for each day of the week, and assign a program to each timetable.
Up to 8 recording programs can be created. Settings relating to recordings such as the recording rate for each camera channel can be configured.
Timetables to special days aside from other days of the week can be assigned.
34
39
40
41
42
47
43
48
Camera
NW camera
Group
Sequence
Network settings of cameras such as the IP address and the port number of the cameras, etc. can be configured.
The title of the camera group can be set.
Settings that required to perform the sequence display of live images from cameras can be configured.
49
54
55
Setup items
Server
NTP
FTP
Proxy
Network
Basic
DDNS
SNMP
Panasonic alarm protocol
User mng.
Basic
Administrator
User
Host
User level
Description
Settings that are required to correct time based on the NTP server, such as the NTP server address, can be configured.
Settings that are required to transmit images from cameras connected to the recorder to a designated FTP server periodically can be configured.
Settings relating to the mail notification function, that sends e-mails to addresses registered in advance at an event or error occurrence, can be configured.
Basic network proxy settings can be configured. Determine whether or not to use the proxy server, and configure the settings such as the server address settings, etc.
Network settings can be configured. Settings that are required to connect to a network such as the IP address and gateway address can be configured.
Setting relating to DDNS can be configured. Determine whether to enable or disable DDNS, and configure the settings of the registered user names, etc.
Settings relating to SNMP can be configured. Configure the settings to check the status of the recorder, etc. by connecting the SNMP manager.
Settings that are required to send a message to addresses registered in advance using "Panasonic alarm protocol" when an event or a problem occurs can be configured.
Reference page
57
58
60
62
63
67
68
69
Determine whether to enable or disable the user authentication and the host authentication.
Information of the registered administrators such as the administrator name, password, the default screen, etc can be edited.
Settings relating to the user authentication such as user registration can be configured. User information can be edited or deleted.
User name, password and operational level can be set.
Settings relating to the host authentication such as registration of PCs (hosts) to allow to access the recorder via a network can be configured. Host information can be edited or deleted.
Operational levels and IP addresses of PCs can be set.
Functions operable in each user level can be set.
70
71
72
74
76
9
10
Setup items
Maintenance
Product information
Disk information
Network information
Disk
Settings management
Config.
Disk information
Format
Description
Versions of the software, the hardware (this recorder), MAC address, serial number, temperature inside the recorder and software version of the connected extension unit will be displayed.
Disk partition information of the recorder will be displayed.
Information such as the recording information, operational mode of the hard disk drives, disk capacities, available capacity of each recording area, etc. will be displayed.
Network information such as IP addresses of NW camera connected to the recorder, communication rate to network, etc. will be displayed.
Settings relating to an action to be taken when available capacity of the hard disk drives run out can be configured, and data recorded on the hard disk drives can be deleted.
The settings of the recorder can be saved and the saved settings can be loaded to the recorder.
Reference page
78
79
82
83
85
Information such as the recording information, operational mode of the hard disk drives, disk capacities, available capacity of each recording area, etc. will be displayed.
Assignment of event recording area and copy area, and formatting of the hard disk drives can be performed.
87
89
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement