- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Battery chargers
- Studer Innotec
- XTH 5000-24
- Installation and operating instructions
FIGURE ELEMENT'S (AC PART). Studer Innotec XTH 6000-48, XTH 5000-24, XTH 8000-48
Add to My manuals36 Pages
advertisement
![FIGURE ELEMENT'S (AC PART). Studer Innotec XTH 6000-48, XTH 5000-24, XTH 8000-48 | Manualzz FIGURE ELEMENT'S (AC PART). Studer Innotec XTH 6000-48, XTH 5000-24, XTH 8000-48 | Manualzz](http://s1.manualzz.com/store/data/003518102_1-403b97cd5bef6cd79cac60fbfc9baf6e-360x466.png)
STUDER Innotec Xtender
13
Figure element's (AC part)
Elem.
Description
A
Comment
Input supply cable The section is determined by means of the maximum current at source and the protection device (H). In multi-unit systems, cables (A) of the same phase must have the same length and section (see comment fig. 12-2/3).
C cable
Connection of the neutrals same length and section (see comment fig. 12-2/3). The section must be selected by means of the Xtender’s output current given on the type plate and the protection device selected for the input (see fig.
1a).
See chapter 4.2 - p. 10.
In a fixed installation where the neutral is connected to the earth at a single installation point upstream of the Xtender, it is permissible to carry out a connection of the neutrals in order to preserve an unchanged earthing system downstream, independent of the operating mode of the Xtender. This choice shows the advantage of keeping the differential protection devices downstream of the
Xtender.
This connection (C) is not permitted if a socket is installed upstream of the Xtender. breaker
E Earth-neutral connection bridge
U) according to the local requirements and in compliance with the applicable regulations and standards.
The neutral is earthed at a single point of the installation, downstream of the source and upstream of the protection device(s) at the default current (DDR). When several sources are available, each source must have an earthed neutral. If the source has to be retained with an isolated earthing system (IT) the applicable local provisions and regulations must be applied.
F AC output protection devices used may be installed downstream of the Xtender (main circuit for the Xtender breaker before distribution). The cable section is to be dimensioned according to the calculation table of maximum output current (fig. 1).
The Xtender has an internal current limitation the value of which is
G Generator stated on the type plate Fig. 1b (35).
The generator is dimensioned according to the requirements of the user. Its rated current will determine the configuration adjustment
{1107} “maximum current of the AC source”. at the Xtender dimensioned according to the power output of the source at the input cable section used. It will not exceed a calibre equivalent to the input current “I AC in” given on the type plate of the unit Fig. 1b (35).
J socket
L
P
R
S Secured grid connection cable must not exceed a length of 2 m, and the socket must remain permanently accessible. The socket will be protected by a protection device of appropriate calibre. The connection of the neutrals (C) is prohibited in this case.
Distribution to the users supplied by the grid or the generator when this is present or by the Xtender within the limit of its power output from energy stored in the battery. This distribution is carried out in conformity with the local standards and regulations.
Installation and operating Instructions Xtender V1.3 Page 30
advertisement
Related manuals
advertisement
Table of contents
- 3 INTRODUCTION
- 3 GENERAL INFORMATION
- 6 ASSEMBLY AND INSTALLATION
- 9 CABLING
- 15 POWERING UP THE INSTALLATION
- 16 DESCRIPTION AND FUNCTIONING
- 24 CONTROL
- 26 MAINTENANCE OF THE INSTALLATION
- 26 PRODUCT RECYCLING
- 26 EC DECLARATION OF CONFORMITY
- 27 COMMENTS OF ANNEXES’ FIGURES
- 29 FIGURE ELEMENT'S (DC PART)
- 30 FIGURE ELEMENT'S (AC PART)
- 31 ELEMENTS OF CONNEXION CABINET (FIG 4A)
- 32 CONTROL AND DISPLAY PARTS FOR THE XTENDER (FIG. 4B)
- 32 TYPE PLATE ELEMENTS (FIG. 1B)
- 34 TABLE OF STANDARD CONFIGURATIONS
- 36 TECHNICAL DATA