Managing Image Cartridge

Expected Cartridge Life

The life of your image cartridge depends on the amount of toner used in each print job. For instance, when you print a typical business letter with about 5% page coverage, you can expect a print cartridge life of approximately 5,000 pages. The actual number may vary according to the print density of the page you print. If you print a lot of graphics, you may need to change the cartridge more often.

You can extend the life of your print cartridge by using Econo Mode setting. Econo Mode uses approximately 50% less toner than normal printing. The printed image is much lighter, and is adequate for printing drafts or proofs.

Replacing Image Cartridge

When the image cartridge is near the end of its life, white streaks or hue changes will occur. You can temporarily re-establish print quality by redistributing the remaining toner in the cartridge.

1. Open the cover and remove the image cartridge.

2. Gently shake the cartridge to distribute the toner evenly inside the cartridge.

3. Reinstall the cartridge and close the cover.

This is typically successful one time only. When the toner will eventually run out, white pages will be printed when a print job is sent, or when a fax is received. The print cartridge needs to be replaced. See the following page.

Maintenance

3.13

To replace the image cartridge:

1. Pulling the cover release button toward you, open the machine cover.

2. Remove the old image cartridge.

Follow the instructions printed on the cartridge box to recycle the used cartridge.

3.14

Maintenance

3. Unpack a new image cartridge, and carefully remove the sealing tape.

4. Shake the cartridge from side to side 5 or 6 times to distribute the toner evenly inside the cartridge.

5. Find the cartridge slots inside the machine, one on each side. Grasp the handle and slide the cartridge down between the cartridge slots until it drops into place.

6. Close the cover firmly.

Maintenance

3.15

3.16

Maintenance

Memo

Appendix

4.1

Appendix

FCC Regulations

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

¥ Reorient or relocate the receiving antenna.

¥ Increase the separation between the equipment and receiver.

¥ Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

¥ Consult the dealer or an experienced radio/TV technician for help.

Do not make any changes or modifications to the equipment unless specified in the manual.

If such changes or modifications should be made, you could be required to stop operation of the equipment.

Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of

FCC Rules.

Canadian Radio Interference Regulations

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled ÒDigital

ApparatusÓ, ICES-003 of the Industry and Science Canada.

Cet appareil numŽrique respecte les limites de bruits radioŽlectriques applicables aux appareils numŽriques de Classe B prescrites dans la norme sur le matŽriel brouilleur:

ÒAppareils NumŽriquesÓ, NMB-003 ŽdictŽe par lÕIndustrie et Sciences Canada.

4.2

Appendix

EC Declaration of Conformity

We,

SAMSUNG ELECTRONICS CO.,LTD

#259, Gong Dan-Dong, Gumi-City, Kyung Buk, Korea declare sole responsibility that the

SF-5800/SF-5800P Laser Facsimile meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility and Low

Voltage Directive 73/23/EEC.

Compliance was demonstrated to the following specifications as listed in the official journal of the European Communities:

EN 50081-Emissions:

EN 55022 Radiated, Class B

EN 55022 Conducted, Class B

EN 60555-2 Power Harmonics

EN 50082-Immunity:

IEC 801-2 Electrostatic Discharge

IEC 801-3 RF Radiated

IEC 801-4 Fast Transient/Burst

EN 60950-Safety

Appendix

4.3

Laser Safety Statement

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR

Subchapter J for Class I(1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 825.

Class I laser products are not considered to be hazardous. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

WARNING Never operate or service the printer with the protective cover removed from the Laser/Scanner assembly. The reflected beam, although invisible, can damage your eyes.

CAUTION -INVISIBLE LASER RADIATION WHEN THIS COVER IS OPEN.

DO NOT OPEN THIS COVER

VORSICHT -UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG

GEÖFFENT. NICHT DEM STRAHL AUSETZEN.

ATTENTION -RAYONNEMENT LASER INVISIBLE EN CAS D’OVERTURE.

DANGEREUSE AU FAISCEAU.

ATTENZIONE -RADIAZIONE LASER INVISIBILE IN CASO DIAPERTURA.

EVITARE L’ESPOSIZIONE AL FASCIO.

PRECAUCION -RADIACION LASER IVISIBLE CUANDO SE ABRE. EVITAR EXPONERSE AL

RAYO.

ADVARSEL -USYNLIG LASERSTRÅLNING VED ÅBNING NÅR SIKKERHEDSBRYDERE

ER UDE AF FUNKTION UNDGÅ UDSAETTELSE FOR STRÅLNING.

ADVARSER -USYNLIG LASERSTRÅLNING NÅR DEKSEL ÅPNES. STIRR IKKE INN I

STRÅLEN. UNNGÅ EKSPONERING FOR STRÅLEN.

VARNING -OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPAND OCH SPÄRREN

ÅR URKOPPLAD. BETRAKTA EJ STRÅLEN STRÅLEN AR FARLIG.

VARO -AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.

4.4

Appendix

Laser product labels are located above the print cartidge.

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

APPAREIL À LASER DE CLASSE 1

TO IEC 825

Safety Information

PRODUCT SAFETY

USA

CANADA

EEC (Europe)

CB

UL 1950 (UL LISTING)

CSA C22.2 No. 950 & UL 1950 (CSA Certification)

IEC 60950/EN 60950 (T Ü V GS Certification)

IEC 60950

LASER SAFETY

EEC (Europe)

USA

HD 194. & EN 60825

21 CFR, Chapter 1, Subchapter J (CDRH Certified)

Appendix

4.5

Power Saver

This printer contains advanced energy conservation technology that reduces power consumption when it is not in active use.

When the printer does not receive data for an extended period of time, power consumption is automatically lowered. For potentially faster printing of the first page, you may turn the power save off from the Remote Control Panel setting.

The energy star emblem does not represent EPA endorsement of any product or service.

The equipment has been approved to [Commission Decision “CTR 21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

In the event of problems, you should contact you contact your equipment supplier in the first instance.

4.6

Appendix

Specifications

Applicable line

Data coding

Modem speed

Transmission speed

Effective scanning width

Effective printing width

Scanning method

Public Switched Telephone Network (PSTN) or behind PABX

MH/MR/MMR

14400/12000/9600/7200/4800/2400 bps

Approx. 6 sec. (V.17 ECM: 14.4 kbps)

8.3 inches (210 mm)

8.2 inches (202 mm)

Sheet-fed Contact Image Sensor (CIS)

Printing speed

Automatic document feeder

8 PPM

30 pages (based on 20 Ib or 75 g/m 2 )

Power requirements

Power consumption

Environmental conditions

Auto dialer

Document size Ð Width

Ð Length

- Weight

(thickness)

220/240 VAC, 50/60 Hz

(Standby) 13 W

Temperature : 50¡F to 86¡F (10¡C to 30¡C)

Humidity : 30% to 80% RH

One-touch dialing (registration for 20 numbers)

Speed dialing (Registration for 80 numbers)

5.8 to 8.5 inches (148 to 216 mm)

Single page : 5 to 59 inches (128 to 1,500 mm)

Multi pages : 8.3 to 11.7 inches (279 to 297 mm)

Single page : 50 to 100g/m 2 (0.07 to 0.20 mm)

20 pages : 50 to 90g/m

30 pages : 75g/m 2

2 (0.07 to 0.13 mm), Uncoated paper

(0.1 mm), Uncoated paper

Recording paper size Letter : 8.5 ✕ 11 inches (216 ✕ 279 mm)

- for automatic feeder A4 : 8.3 ✕ 11.6 inches (210 ✕ 297 mm)

Legal : 8.5 ✕ 14 inches (216 ✕ 356 mm) weight : 60 to 90 g/m 2

Ð for manual feeder thickness : 0.08 to 0.12 mm min. : 4 ✕ 5.9 inches (100 ✕ 149 mm)

(weight : 60 to 130 g/m 2 )

Recording paper capacity Paper : 150 sheets (based on 75g/m 2 paper)

Other media : Up to 5 sheets (OHP, envelopes, labels)

Printing method

Scanning density Ð Horizontal

Ð Vertical

Image cartridge life

Laser Scanning Unit

300 dpi

Standard : 3.85 lines/mm (98 Lpi)

Fine : 7.7 lines/mm (196 Lpi)

Super fine : 11.8 lines/mm (300 Lpi)

5,000 @ 5 % coverage(A4)

Appendix

4.7