advertisement
8: Device Ports
Console Port
The console port initially has the same defaults as the device ports. Use the
page to change the settings, if desired.
To set console port parameters:
1.
Click the Devices tab and select Console Port. The following page displays:
Figure 8-9 Devices > Console Port
2.
Change the following as desired:
Baud
Data Bits
Stop Bits
Parity
Flow Control
Timeout
Show Lines on
Connecting
The speed with which the device port exchanges data with the attached serial device.
From the drop-down list, select the baud rate. Most devices use 9600 for the administration port, so the console port defaults to this value.
Number of data bits used to transmit a character. From the drop-down list, select the number of data bits. The default is 8 data bits.
The number of stop bits that indicate that a byte of data has been transmitted.
From the drop-down list, select the number of stop bits. The default is 1.
Parity checking is a rudimentary method of detecting simple, single-bit errors.
From the drop-down list, select the parity. The default is none.
A method of preventing buffer overflow and loss of data. The available methods include none, xon/xoff (software), and RTS/CTS (hardware). The default is none.
The number of minutes (1-30) after which an idle session on the console is automatically logged out. Disabled by default.
If selected, when you connect to the console port with a terminal emulator, you will see the last lines output to the console, for example, the SLC boot messages or the last lines output during a CLI session on the console.
SLC™ Console Manager User Guide 114
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Copyright and Trademark
- 2 Warranty
- 2 Open Source Software
- 2 Contacts
- 2 Disclaimer and Revisions
- 3 Revision History
- 5 Table of Contents
- 14 List of Figures
- 18 List of Tables
- 19 Chapter Summaries
- 21 Conventions
- 21 Additional Documentation
- 22 SLC Models and Part Numbers
- 24 System Features
- 25 Protocols Supported
- 25 Access Control
- 25 Device Port Buffer
- 25 Configuration Options
- 26 Hardware Features
- 26 Serial Connections
- 27 Network Connections
- 27 PC Card Interface
- 28 USB Port
- 29 What’s in the Box
- 30 Product Information Label
- 30 Technical Specifications
- 31 Physical Installation
- 31 Connecting to Device Ports
- 32 Connecting to Network Ports
- 32 Connecting to Terminals
- 32 Power
- 32 AC Input
- 33 DC Input
- 34 Recommendations
- 34 IP Address
- 35 Method #1 Using the Front Panel Display
- 35 Before you begin, ensure that you have:
- 35 Front Panel LCD Display and Keypads
- 36 Navigating
- 37 Entering the Settings
- 38 Restoring Factory Defaults
- 38 To use the LCD display to restore factory default settings:
- 38 Method #2 Quick Setup on the Web Page
- 38 To complete the Quick Setup page:
- 39 Network Settings
- 40 Date & Time Settings
- 40 Administrator Settings
- 40 Method #3 Quick Setup on the Command Line Interface
- 41 To complete the command line interface Quick Setup script:
- 43 Next Step
- 44 Web Interface
- 46 Logging In
- 46 To log in to the SLC console manager web interface:
- 47 Logging Out
- 47 To log off the SLC web interface:
- 47 Web Page Help
- 47 To view detailed information about an SLC web page:
- 47 Command Line Interface
- 47 Logging In
- 47 To log in to the SLC command line interface:
- 48 To log in any other user:
- 48 Logging Out
- 48 Command Syntax
- 49 Command Line Help
- 49 Tips
- 50 General CLI Commands
- 50 To configure the current command line session:
- 50 To set the number of lines displayed by a command:
- 50 To show current CLI settings:
- 50 To view the last 100 commands entered in the session:
- 51 To clear the command history:
- 51 To view the rights of the currently logged-in user:
- 52 Requirements
- 53 To enter settings for one or both network ports:
- 54 Eth1 and Eth2 Settings
- 55 Gateway
- 55 Hostname & Name Servers
- 56 DNS Servers
- 56 DHCP-Acquired DNS Servers
- 56 GPRS-Acquired DNS Servers
- 56 TCP Keepalive Parameters
- 56 Ethernet Counters
- 56 Network Commands
- 56 To configure Ethernet port 1 or 2:
- 57 To configure up to three DNS servers:
- 57 To set the default and alternate network gateways:
- 57 To set the SLC host name and domain name:
- 57 To set TCP Keepalive and IP Forwarding network parameters:
- 57 To view all network settings:
- 57 To view Ethernet port settings and counters:
- 57 To view DNS settings:
- 57 To view gateway settings:
- 57 To view the host name of the SLC unit:
- 58 IP Filter
- 58 Viewing IP Filters
- 58 To view a list of IP filters:
- 59 Enabling IP Filters
- 59 To enable IP filters:
- 59 Configuring IP Filters
- 59 To add an IP filter:
- 60 Rule Parameters
- 62 Updating an IP Filter
- 62 To update an IP filter rule set:
- 62 Deleting an IP Filter
- 62 To delete an IP filter rule set:
- 62 Mapping a Ruleset
- 62 To map a rule set to a network interface:
- 62 To delete a mapping:
- 62 IP Filter Commands
- 62 To enable or disable IP filtering for incoming network traffic:
- 62 To set IP filter mapping:
- 63 To set IP filter rules:
- 63 Routing
- 63 To configure routing settings:
- 64 Dynamic Routing
- 64 Static Routing
- 64 Equivalent Routing Commands
- 64 To configure static or dynamic routing:
- 64 To set the routing table to display IP addresses (disable) or the corresponding host names (enable):
- 65 VPN
- 65 To complete the VPN page:
- 68 System Logging and Other Services
- 68 SSH/Telnet/Logging
- 69 System Logging
- 70 Audit Log
- 70 SMTP
- 70 SSH
- 71 Telnet
- 71 Web SSH/Web Telnet Settings
- 71 Phone Home
- 72 SNMP
- 73 Communities
- 73 Version 3
- 74 V3 Read-Only User
- 74 V3 Read-Write User
- 74 SNMP, SSH, Telnet, and Logging Commands
- 74 To configure services (system logging, SSH and Telnet access, SSH and Telnet timeout, SNMP agent, email (SMTP) server, and audit log):
- 75 To view current services:
- 75 NFS and SMB/CIFS
- 76 To configure NFS and SMB/CIFS:
- 76 SMB/CIFS Share
- 77 NFS and SMB/CIFS Commands
- 77 To mount a remote NFS share:
- 77 To unmount a remote NFS share:
- 77 To view NFS share settings:
- 77 To configure the SMB/CIFS share, which contains the system and device port logs:
- 77 To change the password for the SMB/CIFS share login (default is cifsuser):
- 77 To view SMB/CIFS settings:
- 78 Secure Lantronix Network
- 78 To access Secure Lantronix Managers and Spider devices on the local network:
- 79 To directly access the CLI interface for a device:
- 79 To configure how Secure Lantronix devices are searched for on the network:
- 80 Secure Lantronix Network Commands
- 80 To detect and view all SLC console manager or user-defined IP addresses on the local network:
- 81 To detect and display all secure Lantronix managers and Spider devices on the local network:
- 81 Date and Time
- 81 To set the local date, time, and time zone:
- 82 To synchronize the SLC unit with a remote timeserver using NTP:
- 82 Date and Time Commands
- 82 To set the local date, time, and local time zone (one parameter at a time):
- 82 To view the local date, time, and time zone:
- 82 To synchronize the SLC console manager with a remote time server using NTP:
- 83 To view NTP settings:
- 83 Web Server
- 83 To configure the Web Server:
- 84 Admin Web Commands
- 84 To configure the timeout for web sessions:
- 84 To configure the web server to use SSLv2 in addition to SSLv3 and TLSv1:
- 85 To configure the strength of the cipher used by the web server
- 85 To enable or disable iGoogle Gadget web content:
- 85 To configure the group that can access the web:
- 85 To configures the banner displayed on the web home page:
- 85 To define a list of network interfaces the web is available on:
- 85 To terminate a web session:
- 85 To view the current sessions and their ID:
- 85 To import an SSL certificate or reset the web server certificate to the default:
- 85 Services - Web Sessions
- 85 To view or terminate current web sessions:
- 86 Services - SSL Certificate
- 86 To view, reset, import, or change an SSL Certificate:
- 88 Web Server Commands
- 88 iGoogle Gadgets
- 88 To set up an SLC iGoogle gadget:
- 90 Connection Methods
- 90 Permissions
- 91 Device Status
- 92 Device Port Settings
- 93 To set up Telnet, SSH, and TCP port numbering:
- 93 Telnet/SSH/TCP in Port Numbers
- 93 To set limits on direct connections:
- 93 To configure a specific port:
- 93 Global Commands
- 93 To configure settings for all or a group of device ports:
- 94 To view global settings for device ports:
- 94 Device Ports - Settings
- 94 To open the Device Ports - Settings page:
- 96 Device Port Settings
- 96 IP Settings
- 97 Data Settings
- 98 Hardware Signal Triggers
- 98 Modem Settings
- 99 Modem Settings: Text Mode
- 99 Modem Settings: PPP Mode
- 101 Port Status and Counters
- 101 Device Ports - SLP / ServerTech CDU
- 101 To open the Device Ports - SLP page:
- 102 To enter SLP commands:
- 102 Status/Info
- 103 SLP Commands
- 103 Device Port - Sensorsoft Device
- 104 Device Port Commands
- 104 To configure a single port or a group of ports (for example, set deviceport port 2-5,6,12,15- 16 baud 2400):
- 105 To view the settings for one or more device ports:
- 105 To view a list of all device port names:
- 105 To view the modes and states of one or more device port(s):
- 105 To view device port statistics and errors for one or more ports:
- 105 To zero the port counters for one or more device ports:
- 106 Device Commands
- 106 To send commands to (or control) a device connected to an SLC device port over the serial port:
- 107 Interacting with a Device Port
- 107 To connect to a device port to monitor it:
- 107 To connect to a device port to monitor and/or interact with it, or to establish an outbound network connection:
- 108 Device Ports - Logging
- 108 Local Logging
- 108 NFS File Logging
- 108 USB Flash Drive Logging
- 109 PC Card Logging
- 109 Email/SNMP Notification
- 109 Sylogs Logging
- 109 To set logging parameters:
- 110 Local Logging
- 110 Email/SNMP Traps
- 111 Log Viewing Attributes
- 112 NFS File Logging
- 112 USB/PC Card Logging
- 112 Syslog Logging
- 112 Logging Commands
- 112 To configure logging settings for one or more device ports:
- 113 To view a specific number of bytes of data for a device port:
- 113 To clear the local log for a device port:
- 114 Console Port
- 114 To set console port parameters:
- 115 Console Port Commands
- 115 To configure console port settings:
- 115 To view console port settings:
- 115 Host Lists
- 115 To add a host list:
- 116 Host Parameters
- 117 To view or update a host list:
- 118 Host Parameters
- 119 To delete a host list:
- 119 Host List Commands
- 119 To configure a prioritized list of hosts to be used for modem dial-in connections:
- 119 To add a new host entry to a list or edit an existing entry:
- 119 To move a host entry to a new position in the host list:
- 119 To delete a host list, or a single host entry from a host list:
- 119 To display the members of a host list:
- 120 Scripts
- 120 To add a script:
- 121 Scripts
- 122 User Rights
- 122 To view or update a script:
- 123 To rename a script:
- 123 To delete a script:
- 123 To change the permissions for a script:
- 123 To use a script at the CLI:
- 123 Batch Script Syntax
- 124 Interface Script Syntax
- 125 Primary Commands
- 127 Secondary Commands
- 128 Control Flow Commands
- 129 Sample Scripts
- 129 Interface Script—Monitor Port
- 131 Batch Script—SLC CLI
- 133 Sites
- 133 To add a site:
- 135 To view or update a site:
- 135 To delete a site:
- 135 To create or edit a site:
- 135 To delete a site:
- 136 Modem Dialing States
- 136 Dial In
- 136 Dial-back
- 137 Dial-on-demand
- 137 Dial-in & Dial-on-demand
- 138 Dial-back & Dial-on-demand
- 139 CBCP Server
- 140 Set Up of PC Card Storage
- 142 Modem Settings
- 144 Data Settings
- 144 ISDN Settings
- 144 GSM/GPRS Settings
- 145 Text Mode
- 145 PPP Mode
- 146 IP Settings
- 147 PC Card Commands
- 148 Set Up of USB Storage
- 148 To configure the USB port, from the USB Ports table,
- 149 To configure the USB Modem port, from the Modem USB Ports table:
- 151 Data Settings
- 151 GSM/GPRS Settings
- 151 Modem Settings
- 152 Text Mode
- 153 PPP Mode
- 154 IP Settings
- 155 Manage Firmware and Configuration Files
- 156 USB Commands
- 157 Types of Endpoints and Connections
- 157 Typical Setup Scenarios for the SLC Unit
- 157 Terminal Server
- 158 Remote Access Server
- 158 Reverse Terminal Server
- 159 Multiport Device Server
- 159 Console Server
- 160 Connection Configuration
- 160 To create a connection:
- 162 To view, update, or disconnect a current connection:
- 163 Connection Commands
- 163 To connect to a device port to monitor and/or interact with it, or to establish an outbound network connection:
- 163 To configure initial timeout for outgoing connections:
- 163 To monitor a device port:
- 163 To connect a device port to another device port or an outbound network connection (data flows in both directions):
- 164 To connect a device port to another device port or an outbound network connection (data flows in one direction):
- 164 To terminate a bidirectional or unidirectional connection:
- 164 To view connections and their IDs:
- 164 To display details for a single connection:
- 164 To display global connections:
- 165 To enable, disable, and set the precedence of authentication methods:
- 167 Authentication Commands
- 167 To set ordering of authentication methods:
- 167 To view authentication methods and their order of precedence:
- 168 Local and Remote User Settings
- 169 To enable local and/or remote users:
- 169 Adding, Editing or Deleting a User
- 169 To add a user:
- 173 Shortcut
- 173 To add a user based on an existing user:
- 173 To edit a local user:
- 173 To delete a local user:
- 173 To change the sysadmin password:
- 173 Local Users Commands
- 173 To configure local accounts (including sysadmin) who log in to the SLC console manager by means of SSH, Telnet, the Web, or the console port:
- 174 To set whether a complex login password is required:
- 174 To enable or disable authentication of local users:
- 174 To set a login password for the local user:
- 174 To delete a local user:
- 174 To view settings for all users or a local user:
- 174 To block (lock out) a user's ability to log in:
- 174 To allow (unlock) a user's ability to log in:
- 174 Local User Rights Commands
- 174 To add a local user to a user group or to change the group the user belongs to:
- 174 To set a local user's permissions (not defined by the user group):
- 175 To remove a permission, type a minus sign before the two-letter abbreviation for a user right.
- 175 To view the rights of the currently logged-in user:
- 175 Remote User Commands
- 175 To configure whether remote users who are not part of the remote user list will be authenticated:
- 175 To configure attributes for users who log in by a remote authentication method:
- 175 To remove a permission, type a minus sign before the two-letter abbreviation for a user right.
- 175 To remove a remote user:
- 175 To view settings for all remote users:
- 175 To view the rights of the currently logged-in user:
- 176 NIS
- 176 To configure the SLC unit to use NIS to authenticate users:
- 178 NIS Commands
- 178 To configure the SLC unit to use NIS to authenticate users who log in via the Web, SSH, Telnet, or the console port:
- 179 To set group and permissions for NIS users:
- 179 To set permissions for NIS users not already defined by the user rights group:
- 179 To remove a permission, type a minus sign before the two-letter abbreviation for a user right.
- 179 To set a default custom menu for NIS users:
- 179 To view NIS settings:
- 179 LDAP
- 179 To configure the SLC unit to use LDAP to authenticate users:
- 183 LDAP Commands
- 183 To configure the SLC unit to use LDAP to authenticate users who log in via the Web, SSH, Telnet, or the console port:
- 184 To set user group and permissions for LDAP users:
- 184 To remove a permission, type a minus sign before the two-letter abbreviation for a user right.
- 184 To set a default custom menu for LDAP users:
- 184 To view LDAP settings:
- 185 RADIUS
- 185 To configure the SLC unit to use RADIUS to authenticate users:
- 188 RADIUS Commands
- 188 To configure the SLC console manager to use RADIUS to authenticate users who log in via the Web, SSH, Telnet, or the console port:
- 188 To identify the RADIUS server(s), the text secret, and the number of the TCP port on the RADIUS server:
- 188 To set the number of seconds after which the connection attempt times out:
- 188 To set user group and permissions for RADIUS users:
- 188 To set permissions for RADIUS users not already defined by the user rights group:
- 189 To remove a permission, type a minus sign before the two-letter abbreviation for a user right.
- 189 To set a default custom menu for RADIUS users:
- 189 To view RADIUS settings:
- 189 User Attributes & Permissions from LDAP Schema or RADIUS VSA
- 190 Kerberos
- 190 To configure the SLC unit to use Kerberos to authenticate users:
- 193 Kerberos Commands
- 193 To configure the SLC unit to use Kerberos to authenticate users who log in via the Web, SSH, Telnet, or the console port:
- 193 To set user group and permissions for Kerberos users:
- 194 To set permissions for Kerberos users not already defined by the user rights group:
- 194 To remove a permission, type a minus sign before the two-letter abbreviation for a user right.
- 194 To set a default custom menu for Kerberos users:
- 194 To view Kerberos settings:
- 194 TACACS+
- 194 To configure the SLC console manager to use TACACS+ to authenticate users:
- 197 TACACS+ Commands
- 197 To configure the SLC console manager to use TACACS+ to authenticate users who log in via the Web, SSH, Telnet, or the console port:
- 197 To set user group and permissions for TACACS+ users:
- 197 To set permissions for TACACS+ users not already defined by the user rights group:
- 198 To remove a permission, type a minus sign before the two-letter abbreviation for a user right.
- 198 To set a default custom menu for TACACS+ users:
- 198 To view TACACS+ settings:
- 198 Groups
- 198 To configure Groups in the SLC console manager:
- 201 To view or update a group:
- 201 To delete a group:
- 201 SSH Keys
- 201 Imported Keys
- 202 Exported Keys
- 202 To configure the SLC unit to use SSH keys to authenticate users:
- 203 Imported Keys (SSH In)
- 203 Host & User Associated with Key
- 204 Host & Login for Import
- 204 Exported Keys (SSH Out)
- 205 Host and Login for Export
- 205 To view or delete a key:
- 206 To view, reset, or import SSH RSA1, RSA, And DSA host keys:
- 207 SSH Commands
- 207 To import an SSH key:
- 207 To export a key:
- 208 To export the public keys of all previously created SSH keys:
- 208 To delete a key:
- 208 To import an SLC host key or to reset a SLC host key to the default:
- 208 To reset defaults for all or selected host keys:
- 208 To display SSH keys that have been imported:
- 208 To display SSH keys that have been exported:
- 208 To display host keys (public key only):
- 209 Custom Menus
- 209 To add a custom menu:
- 212 To view or update a custom menu:
- 212 To delete a custom menu:
- 212 To create a new custom menu from an existing custom menu:
- 212 Custom User Menu Commands
- 212 To assign a custom user menu to a local or remote user:
- 212 To create a new custom user menu or add a command to an existing custom user menu:
- 212 To change a command or nickname within an existing custom user menu:
- 213 To set the optional title for a menu:
- 213 To enable or disable the display of command nicknames instead of commands:
- 213 To enable or disable the redisplay of the menu before each prompt:
- 213 To delete a custom user menu or one command within a custom user menu:
- 213 To view a list of all menu names or all commands for a specific menu:
- 216 SLC Maintenance
- 216 To configure settings:
- 218 Internal Temperature
- 218 Site Information
- 218 SLC Firmware
- 219 Boot Banks
- 219 Load Firmware Via Options
- 219 Configuration Management
- 220 To set the acceptable range for the internal temperature sensor (an SNMP trap is sent if the temperature is outside of this range):
- 221 To display the acceptable range and the current reading from the internal temperature sensor:
- 221 To set the acceptable range for the internal temperature sensor (an SNMP trap is sent if the temperature is outside of this range):
- 221 To display the acceptable range and the current reading from the internal temperature sensor:
- 221 To save the current SLC configuration to a selected location:
- 221 To restore a saved configuration to the SLC:
- 221 To restore the SLC to factory default settings:
- 222 To delete or rename a configuration (the user is prompted for the new name for renames):
- 222 To copy the current configuration (or optionally, a configuration from another location) to the other bank (for dual-boot SLB/SLC units):
- 222 To update the SLB/SLC firmware to a new revision (the firmware file should be accessible via the settings displayed by 'admin ftp show'):
- 222 To set the boot bank to be used at the next SLB/SLC reboot (for dual-boot SLB/SLC units):
- 222 To copy the boot bank from the currently booted bank to the alternate bank (for dual-boot SLB/SLC units):
- 222 To list the current firmware revision, the boot bank status (for dual-boot SLB/SLC units), and optionally displays the log containing details about firmware updates:
- 222 To manage configuration files:
- 223 Administrative Commands
- 223 To copy the boot bank from the currently booted bank to the alternate bank (for dual-boot SLB/SLC units):
- 223 To reboot the SLC:
- 223 To prepare the SLC console manager to be powered off:
- 223 To list current hardware and firmware information:
- 224 To update SLC firmware to a new revision:
- 224 To set the boot bank to be used at the next SLC unit reboot:
- 224 To list the current firmware revision:
- 224 To set the FTP/TFTP/SFTP server used for firmware updates and configuration save/ restore:
- 224 To view FTP settings:
- 224 To set the FTP server password and prevent it from being echoed:
- 224 To restore the SLC console manager to factory default settings:
- 224 To restore a saved configuration to the SLC unit:
- 225 To save the current SLC configuration to a selected location:
- 225 To delete a saved configuration:
- 225 To list the configurations saved to a location:
- 225 To run the quick setup script:
- 225 System Logs
- 225 To view system logs:
- 227 To clear system logs:
- 227 System Log Command
- 227 To view the system logs containing information and error messages:
- 228 To clear one or all of the system logs:
- 228 Audit Log
- 229 Email Log
- 230 Diagnostics
- 231 Diagnostic Commands
- 231 To display the ARP table of IP address-to-hardware address mapping:
- 232 To display a report of network connections:
- 232 To resolve a host name into an IP address:
- 232 To test a device port by transmitting data out the port and verifying that it is received correctly:
- 232 To display the route that packets take to get to a network host:
- 232 To verify that the host is up and running:
- 232 To display performance statistics for an Ethernet port or a device port (averaged over the last 5 seconds):
- 232 To generate and send Ethernet packets:
- 233 To display all network traffic, applying optional filters:
- 233 To display information on the internal memory, storage and processes of the SLC unit:
- 234 Status/Reports
- 234 View Report
- 235 Status Commands
- 235 To display device port modes and states for one or more ports:
- 236 To display a snapshot of configurable parameters:
- 236 To generate a report for one or more ports:You can optionally email the displayed information.
- 236 To display the overall status of all SLC devices:
- 236 To display a list of all current connections:
- 236 To provide details, e.g., endpoint parameters and trigger, for a specific connection:
- 236 Emailing Logs and Reports
- 236 To email a log to an individual:
- 237 To email a log to Lantronix Technical Support:
- 239 Events
- 240 Events Commands
- 240 To manage the response to events that occur in the SLC unit:
- 240 To update event definitions:
- 241 To delete an event:
- 241 To view events:
- 241 LCD/Keypad
- 241 To configure the LCD and Keypad:
- 242 To configure the LCD:
- 242 To configure the Keypad:
- 242 LCD/Keypad Commands
- 243 Banners
- 243 To configure banner settings:
- 244 Banner Commands
- 245 Telnet/SSH to a Remote Device
- 247 Dial-in (Text Mode) to a Remote Device
- 248 Local Serial Connection to Network Device via Telnet
- 250 Introduction to Commands
- 250 Command Syntax
- 251 Command Line Actions and Categories
- 251 Tips
- 252 Deprecated Commands
- 252 Administrative Commands
- 261 Audit Log Commands
- 261 Authentication Commands
- 262 CLI Commands
- 263 Connection Commands
- 266 Console Port Commands
- 267 Custom User Menu Commands
- 269 Date and Time Commands
- 270 Device Commands
- 270 Device Port Commands
- 274 Diagnostic Commands
- 277 Email Log Commands
- 277 Events Commands
- 278 Group Commands
- 279 Host List Commands
- 280 IP Filter Commands
- 282 Kerberos Commands
- 283 LDAP Commands
- 284 Local Users Commands
- 287 Log Commands
- 289 Network Commands
- 291 NFS and SMB/CIFS Commands
- 293 NIS Commands
- 294 PC Card Commands
- 297 RADIUS Commands
- 299 Remote Users Commands
- 300 Routing Commands
- 300 Script Commands
- 302 Services Commands
- 303 Site Commands
- 304 To create or edit a site:
- 304 To delete a site:
- 304 SLC Network Commands
- 305 SSH Key Commands
- 307 Status Commands
- 307 System Log Commands
- 308 TACACS+ Commands
- 309 Temperature Commands
- 309 USB Commands
- 313 User Permissions Commands
- 313 VPN Commands
- 313 Parameters
- 315 Accessing the Bootloader
- 315 Bootloader Commands
- 316 Administrator Commands
- 317 Security Practice
- 317 Factors Affecting Security
- 318 Cover
- 318 Power Plug
- 318 Input Supply
- 319 Grounding
- 319 Fuses
- 319 Rack
- 320 Port Connections
- 321 Geräteabdeckung
- 321 Netzstecker
- 322 Stromversorgung
- 322 Anschluß an die Schutzerde
- 322 Gerätesicherung
- 322 Rack / Einbauschrank
- 323 Signalverbindungen
- 340 Installing Schema Support in Window AD Server
- 344 Creating the SLC Schema Attribute
- 345 Adding the Attribute to the Users Group in Windows
- 348 Adding the Permissions to the Individual User
- 350 Values to Use
- 351 String Format