advertisement
Chapter 4: Operation
4.2 RS-232 Communication Commands
Table 4-1. RS-232 commands.
Switch Commands
Command Function
50701% Switch to HDMI input
Feedback Example
Switch to HDMI
50704% Switch to VGA input
50705% Change the horizontal polarity to the opposite.
Switch to VGA
Hpolarity:0/1
50706% Change the vertical polarity to the opposite. Vpolarity:0/1
50707% Check the present resolution and polarity.
1920 x 1080
Hpolarity:1
Vpolarity:0
50770% Enable auto-switching
50771% Disable auto-switching
Auto Switching
Manual Switching
Resolution Commands
Command Function
50619% Change the resolution to 1360 x 768 HD
Feedback Example
Resolution: 1360 x 768
50626% Change the resolution to 1024 x 768 XGA Resolution: 1024 x 768
50627% Change the resolution to 1280 x 720 720P Resolution: 1280 x 720
50628% Change the resolution to 1280 x 800
WXGA
Resolution: 1280 x 800
50629% Change the resolution to 1920 x 1080
1080P
50620% Change the resolution to 1920 x 1200
WUXGA
50621% Change the resolution to 1600 x 1200
UXGA
Resolution: 1920 x 1080
Resolution: 1920 x 1200
Resolution: 1600 x 1200
NOTE: Commands with grey background are for VGA sources only.
724-746-5500 | blackbox.com
Page 19
Chapter 4: Operation
Table 4-1 (continued). RS-232 commands.
Setup Commands
Command Function
502xx%
503xx%
504xx%
Set the brightness to xx. XX ranges from 00 to 99.
Set the contrast to xx. XX ranges from 00 to 99
Set the saturation to xx. XX ranges from 00 to 99.
Feedback Example
Brightness: xx
Contrast: xx
Saturation: xx
505xx%
50606%
50607%
50608%
50614%
Set the sharpness to xx. XX ranges from 00 to 99.
Auto-adjust the input parameter.
Adjust the color temperature.
Set the aspect ratio.
Set the picture mode.
50699% Check the system version.
50779% Switch to RS-232 mode 1, enable scaler to control far-end devices.
50780% Switch to RS-232 mode 2, enable far-end devices to control scaler.
50790% Set the HDCP status of the HDMI output socket to Active.
Sharpness: xx
VGA Input Auto
Color Temperature: xx (xx can be medium, warm, user, or cool)
Aspect Ratio: xx (xx can be
16:9, 4:3, or auto.)
Picture Mode: xx (xx can be dynamic, standard, mild, or user.)
Version Vx.x.x
RS-232 Mode 1: RS-232 Control
Scaler and Remote
RS-232 Mode 2: RS-232 and
Remote Control Scaler
HDCP Active
50791% Set the HDCP status of HDMI output socket to On.
HDCP On
50792% Set the HDCP status of HDMI output socket to Off.
HDCP Off
50698% Software update.
—
NOTE: Commands with grey background are for VGA sources only.
Page 20 724-746-5500 | blackbox.com
Chapter 4: Operation
Table 4-1 (continued). RS-232 commands.
Setup Commands (continued)
Command Function
50617% Reset to factory default.
Feedback Example
—
Inquire Commands
Command Function
50632%
50633%
50793%
Check the output resolution .
Check the picture mode.
Check HDCP status.
Feedback Example
Resolution: xx
Picture Mode: xx
HDCP Off
HDCP On
HDCP Active
50635% Check the image aspect ratio.
50636% Check the brightness.
50637% Check the contrast.
50638% Check the saturation.
Aspect Ratio: xx
Brightness: xx
Contrast: xx
Saturation: xx
50639% Check sharpness.
50640% Check the color temperature.
Sharpness: xx
Color Temperature: xx
Adjustment Commands
50678% Enable screen output adjusting. Enter Output Position Adjust
50679%
50670%
50671%
50672%
50673%
Disable screen output adjusting.
Move the image to left.
Move the image to right.
Move the image up.
Move the image down.
50674% Stretch left from left side (increase image width).
50675% Pull right from left side (decrease image width).
50676% Stretch upwards from bottom side
(decrease image height).
50677% Stretch downwards from bottom side.
Exit Output Position Adjust
Output Position Adjust X xx
Output Position Adjust X xx
Output Position Adjust Y xx
Output Position Adjust Y xx
Output Width Adjust xx
Output Width Adjust xx
Output Height Adjust xx
Output Height Adjust xx
(increase image height)
724-746-5500 | blackbox.com
Page 21
Chapter 4: Operation
Table 4-1 (continued). RS-232 commands.
EDID Commands
Command Function Feedback Example
50772% EDID passthrough
50773% Set EDID passthrough
EDID: bypass mode
EDID:1080P&PCM 2ch
50774% Set EDID data to 1080P Dolby 5.1
EDID:1080P&5.1ch
50775% Set EDID data to 1080P3D Dolby 5.1 EDID:1080P3d&5.1ch
50776% Set EDID data to 1080i PCM 2.0ch
EDID:1080i&PCM 2ch
50777% Set EDID data to 4K*2K PCM 2.0ch
EDID:4K&PCM 2ch
50778% Check EDID data
50799% Program EDID file, send EDID data within 10s
EDID:1080P&PCM 2ch
EDID:1080P&5.1ch
EDID:1080P3d&5.1ch
EDID:4K&PCM 2ch
Waiting for edid within 10 secs!
NOTES:
1. EDID commands are for HDMI sources only.
Page 22 724-746-5500 | blackbox.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project