Lifting Performance
Maximum lift capacity:
6000 lbs. (2721 kg)
Maximum lift height:
34’-3” (10.44 m)
Capacity at maximum lift height:
4000 lbs. (1820 kg)
Max. forward reach to load center:
23’-3” (7.09 m)
Capacity at maximum forward reach:
900 lbs. (408 kg)
Maximum below grade reach:
24” (610 mm)
Frame leveling:
10 o left/10 o right
General Dimensions
Based on standard machine equipped with listed tires, 48” masonry carriage and 48” pallet forks.
Recommended tire type:
15.00 x 19.5 12-ply
Inflate to 60 psi (415 kPa)
Overall length, less forks:
16’-0” (4.88 m)
Overall width:
7’-10” (2.39 m)
Overall height:
7’-9” (2.36 m)
Ground clearance: 14” (356 mm)
Wheel base: 9’-2” (2.8 m)
Outside turn radius: 12’-6” (3.81 m)
Machine weight:
15,100 lbs. (6855 kg)
Instrumentation
Gauges: Fuel level, hourmeter and coolant temperature
Monitoring lights:
Engine oil pressure, alternator, transmission oil temperature, brake failure
Visual indicators:
Boom angle, frame angle
Chapter 2
SPECIFICATIONS
Steering System
Steer Valve: Fixed displacement rotary
Displacement/Rev: 17.9 cu. in. (293 cc)
System pressure: 2000 psi (138 bar)
Steer cylinders: 1 per axle
Steer mode valve:
3-position, 4-way solenoid with dash-mounted switch actuation
Steer modes: 2-wheel, 4-wheel, crab
Braking System
Service brakes: Oil-immersed inboard hydraulic wet-disc type; separate front and rear systems;
Manual foot pedal actuation
Parking brake: Spring-applied, hydraulicrelease disc-type in front axle
Actuation is electric switch with engine running, automatic with engine off.
Electrical System
Type: 12-volt, negative ground
Battery: 950 cold cranking amps
Circuit protection: Fuse panel
Backup alarm: 107 dB(A)
Horn: 111 dB(A)
Standard features:
Brake lights, rear backup light, neutral start switch
Alternator: 75-amp
Service Capacities
Cooling System: 4.3 gallons (16.3 L)
50/50 mixture
Anti-freeze protection: -34 o F (-31 o C)
Pressure cap: 16 psi (110 kPa)
Fuel tank: 29 gals. (110 L)
Hydraulic reservoir and system: 35 gals. (133 L)
Transmission and cooler: 24 qts. (22.7 L)
Axles:
Differentials: 9.6 qts. (9 L) ea.
Hubs: 0.6 qts. (0.5 L) ea.
Transmission
Type: Clark Powershift T12000
Speeds: 3 fwd / 3 rev
Torque converter:
Single-stage, dual-phase
Travel Speeds:
1st gear: 3.6 mph (5.8 km/h)
2nd gear: 7.9 mph (12.7 km/h)
3rd gear: 20.2 mph (32.5 km/h)
Axles (front and rear)
Type: Dana
Drive/steer, open differential, double reduction planetary, full-time fourwheel drive
Overall ratio: 15.4:1
Engine Options
Features:
Turbocharged In-line 4-cycle,
4-cylinder, direct-injection diesel fuel system, in-line fuel filter w/water trap, positive pressure lubrication, liquid pressurized cooling system,
20” (508 mm) blower fan, dry dual-element air cleaner, spin-on oil filter.
Machines with s/n 16150 thru 16158:
John Deere 4045T Tier 3
276 cu. in. (4523 cc) displacement
84 hp (63 kW) @ 2400 rpm
Oil capacity: 15.5 qts. (14.7 L)
Machines beginning with s/n 16159:
John Deere 4045T Interim Tier 4
276 cu. in. (4523 cc) displacement
74 hp (55 kW) @ 2400 rpm
Oil capacity: 15.5 qts. (14.7 L)
Hydraulic System
Type: Open-center
Pump: Single-section gear type
Displacement / revolution:
2.7 cu. in. (44.3 cc)
Flow @ 2500 RPM:
29 gpm (110 L/min)
Main relief pressure:
3000 psi (207 bar)
Steer relief pressure:
2000 psi (138 bar)
Hydraulic filter:
In-tank return type, 10 micron media, replaceable element.
Rated flow: 100 gpm (379 L/min)
Rated pressure: 100 psi (690 kPa)
By-pass pressure (full flow):
25 psi (172 kPa)
Hydraulic strainer:
In-tank suction, 149 micron media, replaceable element.
Rated flow: 50 gpm (189 L/min)
By-pass pressure: 3 psi (21 kPa)
4
50960008/BP0514 PRINTED IN U.S.A.
Chapter 3
CHECKLISTS
PRE-DELIVERY
The following Checklist is an important reminder of the inspections that MUST be made before delivering the
Telescopic Handler to the customer. Check off each item after the prescribed action is taken.
√ Check that: q
NO parts of machine have been damaged in shipment.
Check for such things as dents and loose or missing parts; correct or replace components as required.
q
Battery is securely mounted and not cracked. Cable connections are tight. Electrolyte at proper level.
q
Cylinders, hoses and fittings are not damaged, leaking or loosely secured.
q
Oil, fuel and air filters are not damaged, leaking or loosely secured.
q
All grease fittings have been properly lubricated and no fittings are missing; see Lubrication chapter of this manual.
q
Wheel nuts are torqued to 450 ft.-lbs. (610 Nm).
q
Tires are inflated to 60 psi (415 kPa) cold.
q
Hydraulic system reservoir, engine crankcase, engine coolant, transmission and axles are filled to the proper operating fluid levels.
q
All adjustments have been made to comply with the settings given in this manual and in the separate engine manual.
q
All guards, shields and decals are in place and securely attached.
q
Model and serial numbers for this unit are recorded in space provided on this page and page 1.
Start the machine and test-run the unit while checking that proper operation is exhibited by all controls.
√ Check that: q
All indicators (lamps, switches, etc.) function properly.
q
All hand and foot controls operate properly.
q
The PWP System operates properly (if equipped). Refer to
Service and Storage chapter for the procedure to check the
PWP System.
q
Boom, Quick-attach ™ System with attachment tool and frame level control all function properly.
q
No hydraulic system leaks when under pressure.
q
Listen for abnormal noises or vibrations; if detected, determine their cause and repair as necessary.
I acknowledge that the pre-delivery procedures were performed on this unit as outlined above.
Dealership’s Name
Dealer Representative’s Name
Date Checklist Filled Out
Machine Model # Machine Serial # Engine Serial #
DELIVERY
√ Check that:
The following Checklist is a reminder of the important information that MUST be passed on to the customer at the time the unit is delivered. Check off each item as it is explained to the customer.
q
Review with the customer the contents of this manual and the AEM Safety Manual for the following: q
The Index at the back, for quickly locating topics; q
The Safety, Indicators and Controls, and Operation and
Adjustment chapters for information regarding safe use of the machine.
q
The Lubrication and Service and Storage chapters for information regarding proper maintenance of the machine.
Explain that regular lubrication and maintenance are required for continued safe operation and long life.
q
Give this Operator’s Manual and the AEM Safety Manual to the customer and instruct them to be sure to read and completely understand their contents before operating the unit.
q
Remind the customer of U.S. OSHA regulation 1910.178
(l), which specifies operator training requirements.
q
Explain that the customer must consult the engine manual
(provided) for related specifications, operating adjustments and maintenance instructions.
q
Completely fill out the Owner’s Registration, including customer’s signature, and return it to the Company.
q
Explain that a copy of the product warranty is included on the inside back cover of this Operator’s Manual.
Customer’s Signature
Date Delivered
(Dealer’s File Copy - Remove at Perforation)
5
PRINTED IN U.S.A.
50960008/BP0514
INTENTIONALLY BLANK
(To be removed as Dealer’s file copy)
50960008/BP0514
6
PRINTED IN U.S.A.