3. Installation. Black Box IC501A
Add to My manuals37 Pages
Black Box IC501A is a SCSI Fiber Optic Bus Extender that provides a simple, reliable, and cost-effective solution for extending SCSI signals over long distances, up to 17,000 feet (5,182 meters) using multimode fiberoptic cable. Ideal for a variety of applications, including extending SCSI peripherals away from noisy environments or connecting SCSI devices in remote locations.
advertisement
IC500A 7/12/00 12:38 PM Page 11
3. Installation
CHAPTER 3: Installation
3.1 Unpacking Your Extender
Unpack your SCSI Fiber Optic Bus Extender from its original shipping carton and check the contents. The package should include:
• (1) SCSI Fiber Optic Bus Extender
• (1) AC power cord (115 or 230 VAC, depending on what you ordered)
• This user’s manual
• 10-ft. (3-m) 9-pin male to 9-pin female RS-232 cable
• 9-pin male to 25-pin female RS-232 adapter
• SCSI Fiber Optic Bus Extender Control software
• Rackmount rails
• Desk-mount rubber feet
• Two loopback connectors
3.2 AC Line Voltage
The Extender can be externally connected to any AC input voltage between 100 and 240 volts. Unless otherwise specified, the Extender will be shipped with a 110volt power cord. Black Box offers a complete source of replacement power cords for most countries and appropriate voltages.
3.3 Placement
Place the Extender near the host computer and peripherals. Make sure the ventilation slots on the sides of the unit obtain adequate airflow. Do not place the
Extender on any devices that generate excessive heat.
3.4 Cable Recommendations
High-quality shielded SCSI cables will provide the greatest noise immunity and distance from the Extender to your peripherals. But in any case, no cables connected to the Extender may exceed 19.7 feet (6 meters) for single-ended or 82 feet (25 meters) for differential devices.
11
advertisement
Related manuals
advertisement
Table of contents
- 7 1. Specifications
- 9 2. Introduction
- 9 Description
- 9 Features
- 12 3. Installation
- 12 Unpacking Your Extender
- 12 AC Line Voltage
- 12 Placement
- 12 Cable Recommendations
- 13 Connecting the SCSI Fiber Optic Bus Extender to the SCSI Bus
- 13 Ensuring Proper SCSI Bus Termination
- 13 Connecting a Fiberoptic Cable
- 14 Connecting a DB9 Coax Cable
- 15 Verify Communications
- 16 4. Operator Controls and Indicators
- 16 AC Switch
- 16 Indicators
- 17 Front-Panel Keypad
- 18 5. Interfacing Requirements
- 18 SCSI Cable Interface Requirements
- 19 Internal/External Terminator Options
- 19 Internal Terminator Power and Fuse
- 20 Selecting Internal Terminator Power
- 20 RS-232 Interface Pin Assignment
- 21 Internal RS-232 Jumper Block
- 21 Rear-Panel Option Switches
- 22 RS-232 Remote Operation Commands
- 24 ASCII Character Reference for SCSI Fiber Optic Bus Extender Box Selection
- 25 5.10 Windows Software
- 25 5.11 Connecting Multiple SCSI Fiber Optic Bus Extenders
- 26 5.12 Rack Mount Installation
- 27 5.13 Fiberoptic Cable Requirements
- 28 6. Operation
- 28 SCSI Fiber Optic Bus Extender Operation
- 28 System Performance
- 28 System Configuration Options
- 30 7. SCSI Technical Information
- 30 SCSI Basics
- 31 SCSI Installation Tips
- 32 SCSI Interface Signal Descriptions