5. Interfacing Requirements. Black Box IC501A
Add to My manuals37 Pages
Black Box IC501A is a SCSI Fiber Optic Bus Extender that provides a simple, reliable, and cost-effective solution for extending SCSI signals over long distances, up to 17,000 feet (5,182 meters) using multimode fiberoptic cable. Ideal for a variety of applications, including extending SCSI peripherals away from noisy environments or connecting SCSI devices in remote locations.
advertisement
IC500A 7/12/00 12:38 PM Page 17
CHAPTER 5: Interfacing Requirements
5. Interfacing Requirements
5.1 SCSI Cable Interface Requirements
The SCSI Fiber Optic Bus Extender can be installed at any point on the SCSI bus.
The Extender provides an optically isolated SCSI bus over extended distances.
Terminators must be installed on both the local and extended bus. Make sure that
a maximum of two terminators are installed on each bus.
The Extender has a 50-pin and a 68-pin connector for narrow and wide SCSI devices, respectively.
5.1.1 S INGLE -E NDED SCSI F IBER O PTIC B US E XTENDER
The IC500A supports a maximum cable length of 19.7 feet (6 meters) at standard
SCSI data rates (5 Mbps, narrow), or 9 feet (2.7 meters) at “Fast” SCSI data rates
(10 Mbps).
5.1.2 D
IFFERENTIAL
SCSI F
IBER
O
PTIC
B
US
E
XTENDER
The IC501A supports a maximum cable length of 82 feet (25 meters) at standard or “Fast” SCSI data rates.
NOTE
Do not connect devices to both the Wide and Narrow connectors at the same time. This will cause termination and noise problems in your system.
Do not intermix single-ended and differential devices on any one side of the SCSI chain unless a SCSI differential converter is used to convert from one bus type to the other.
17
advertisement
Related manuals
advertisement
Table of contents
- 7 1. Specifications
- 9 2. Introduction
- 9 Description
- 9 Features
- 12 3. Installation
- 12 Unpacking Your Extender
- 12 AC Line Voltage
- 12 Placement
- 12 Cable Recommendations
- 13 Connecting the SCSI Fiber Optic Bus Extender to the SCSI Bus
- 13 Ensuring Proper SCSI Bus Termination
- 13 Connecting a Fiberoptic Cable
- 14 Connecting a DB9 Coax Cable
- 15 Verify Communications
- 16 4. Operator Controls and Indicators
- 16 AC Switch
- 16 Indicators
- 17 Front-Panel Keypad
- 18 5. Interfacing Requirements
- 18 SCSI Cable Interface Requirements
- 19 Internal/External Terminator Options
- 19 Internal Terminator Power and Fuse
- 20 Selecting Internal Terminator Power
- 20 RS-232 Interface Pin Assignment
- 21 Internal RS-232 Jumper Block
- 21 Rear-Panel Option Switches
- 22 RS-232 Remote Operation Commands
- 24 ASCII Character Reference for SCSI Fiber Optic Bus Extender Box Selection
- 25 5.10 Windows Software
- 25 5.11 Connecting Multiple SCSI Fiber Optic Bus Extenders
- 26 5.12 Rack Mount Installation
- 27 5.13 Fiberoptic Cable Requirements
- 28 6. Operation
- 28 SCSI Fiber Optic Bus Extender Operation
- 28 System Performance
- 28 System Configuration Options
- 30 7. SCSI Technical Information
- 30 SCSI Basics
- 31 SCSI Installation Tips
- 32 SCSI Interface Signal Descriptions