- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- Jacuzzi
- (2017) J-300™
- Owner's manual
advertisement
J-300
A. Programming the Primary Filtration Cycle
To change the programmed Primary Filtration Cycle:
Note: If no button is pressed within 5 seconds of each selection the screen will revert back to the Main Menu and the current settings will remain active.
1. Press until you get to the “ PF” Menu. The display will scroll
“ PRIMARY FILTER.” After the second scroll, if no action is taken, the system will revert back to the Main Menu.
2. Press or to display the current start time and prepare the system for changes.
3. Press or to adjust the start time, in 1-hour increments. To switch from “AM” to “PM” you must round a 12-hour period.
4. Press
1
to confirm and save the start time.
5. Press or to adjust the duration of cycle, in 1-hour increments.
6. Press
1
to confirm and save the duration time. The system will return to the “ PRIMARY FILTER” Menu.
In extreme bitter cold weather, where freezing can occur, we recommend you program the primary filtration cycle to run 24
hours. Refer to the “Winterizing” section on page 45.
11.2 Secondary Filtration Menu
The jets pump 1 activates during the secondary filtration to provide additional skimming. The spa is programmed with a default setting of
Holiday Mode, but can be programmed to other modes. There are 3 different modes, Holiday, Light and Heavy Mode.
Note: During the secondary filtration the jets pump 1, circulation pump and CLEAR RAY are activated.
• Holiday Mode disables the Secondary Filtration.
• Light Mode will activate two 10-minute cycles every other day; one at 8:00 AM and the other at 8:00 PM.
• Heavy Mode will activate two 10-minute cycles every day; one at 8:00 AM and the other at 8:00 PM.
A. Programming the Secondary Filtration Cycle
To change the programmed Secondary Filtration Cycle:
Note: If no button is pressed within 5 seconds of each selection the screen will revert back to the Main Menu and the current settings will remain active.
1. Press until you get to the “ SF” Menu. The display will scroll
“ SECONDARY FILTER.” After the second scroll, if no action is taken, the system will revert back to the Main Menu.
2. Press or to enter the Secondary Filtration programming.
Continually press to scroll through the following modes:
• Holiday Mode: The screen will display “HOL” and scroll
“HOLIDAY MODE.”
33
advertisement
Related manuals
advertisement
Table of contents
- 7 Important Spa Owner Information
- 7 FCC Notice
- 8 Important Safety Instructions for all Spa Owners
- 12 Entrapment Risk
- 13 3.2 Hyperthermia
- 14 (Canada Only)
- 14 General Electrical Safety Instructions
- 15 Choosing A Location
- 16 Outdoor Location
- 16 Indoor Location
- 17 Remote Monitoring System
- 18 General Electrical Safety Instructions
- 19 Power Requirements
- 21 Electrical Wiring Instructions
- 26 Spa Fill Up Procedure
- 31 Control Functions
- 31 Control Panel
- 32 General Spa Features And Controls
- 33 10.0 Operating Instructions
- 33 10.1 Register Your New Spa
- 34 10.2 Completing Your Registration
- 34 10.3 Setting Water Temperature
- 35 10.4 Activate Jet Pumps
- 35 10.5 Light On/Off Button
- 35 10.6 Light Mode Button
- 36 10.7 Jets
- 36 10.8 Selecting Desired Massage Action
- 36 10.9 Waterfall Feature
- 36 RAY on Demand
- 37 10.11 Air Controls
- 37 10.12 Optional BLUEWAVE® Spa Stereo System
- 37 10.13. Blow-Out Cycle
- 37 10.14 Cleanup Cycle
- 38 11.0 Menu Features and Programming Instructions
- 38 11.1 Primary Filtration Menu
- 39 11.2 Secondary Filtration Menu
- 40 11.3 Programming the Heating Mode
- 41 11.4 Programming the Change Filter Timer
- 41 RAY Timer
- 42 11.6 Programming the Water Refresh Timer
- 42 11.7 Programming the Time
- 43 11.8 Programming the Date
- 43 11.9 Programming the Temperature Format
- 43 11.10 Programming the Language
- 44 11.11 Programming the Lock Feature
- 44 11.12 Resetting the Wi-Fi Connection (optional feature)
- 45 12.0 Spa Maintenance
- 45 12.1 Cleaning The Filters
- 48 12.2 Draining and Refilling
- 49 12.3 Pillow Care
- 49 12.4 Cleaning The Spa Interior
- 49 12.5 Cover Care and Maintenance
- 50 12.6 Tool Free Access Door
- 51 12.7 Maintaining The Synthetic Cabinet
- 51 12.8 Winterizing
- 52 12.9 Restarting Your Spa in Cold Weather
- 52 13.0 Water Quality Maintenance
- 53 13.1 pH Control
- 53 13.2 Sanitizing
- 54 RAY® (Ultraviolet) Water Purification System
- 55 Quartz Tube Maintenance
- 57 14.0 Error Conditions/Error Messages
- 57 14.1 Summer Logic
- 57 14.2 Panel Displays COOL
- 58 14.3 Panel Displays ICE
- 58 14.4 Panel Displays SN
- 58 14.5 Panel Displays SN
- 58 RAY Bulb
- 58 14.7 Panel Displays Change Filter
- 58 14.8 Panel Displays Change Water
- 59 14.9 Panel Displays FL
- 59 14.10 Panel Displays FL
- 59 14.11 Panel Displays OH
- 59 14.12 Panel Displays (-- -- -- --)
- 60 15.0 Troubleshooting Procedures
- 60 15.1 FL--1 and FL
- 60 15.2 None of the Components Operate (e.g. Pump, Light)
- 60 15.3 Pump Does Not Operate
- 61 15.4 Poor Jet Action
- 61 15.5 Water is Too Hot
- 61 15.6 No Heat
- 62 16.0 Circuit Board Diagrams
- 62 J-375 and J-385 Dedicated Power Models (60 Hz)
- 63 Models (For a 3-wire 120V 60 Hz connection)
- 64 Models (For a 4-wire 240V 60 Hz connection)
- 65 J-385 Models (50 Hz)
- 66 16.5 Export J-315 and J-325 Models (50 Hz)
- 67 17.0 Dip Switch Settings and Wiring
- 67 17.1 Switch settings for Domestic 60Hz Models
- 68 17.2 Switch settings for Export 50Hz Models
- 70 17.3 Single Service 50Hz Connection
- 70 17.4 Dual Service 50Hz Connection
- 71 17.5 Three Service 50Hz Connection
- 72 18.0 Optional BLUEWAVE® Spa Stereo System
- 73 18.1 Pairing the Remote and Stereo
- 73 18.2 Audio Settings
- 75 18.3 Wireless Remote Control Functions
- 76 18.4 Electronic Device Connections and Functions
- 78 18.5 Wireless Remote Battery Replacement Procedure
- 79 18.6 BLUEWAVE® Spa Stereo System Specifications
- 79 18.7 Stereo Cautions