- Computers & electronics
- Networking
- American Time
- AllSync IQ ASQMSTR-00X2E
- Installation and Operation Manual
Wired Clock Circuit Option. American Time AllSync IQ ASQMSTR-00X2E, AllSync IQ ASQMSTR-00X6E, AllSync IQ ASQMSTR-00X8E
Add to My manuals57 Pages
advertisement
![Wired Clock Circuit Option. American Time AllSync IQ ASQMSTR-00X2E, AllSync IQ ASQMSTR-00X6E, AllSync IQ ASQMSTR-00X8E | Manualzz Wired Clock Circuit Option. American Time AllSync IQ ASQMSTR-00X2E, AllSync IQ ASQMSTR-00X6E, AllSync IQ ASQMSTR-00X8E | Manualzz](http://s3.manualzz.com/store/data/027711668_1-4e79c81ec46c1b5d712246a1ddef61c5-360x466.png)
Wired Clock Circuit Option
1:49
FRI OCT 3 2014
American Time
800-328-8996
Wired Clock Circuit Installation
To install wired clock circuits:
1. Disconnect and lock out power to the AllSync IQ Master and any circuit wiring.
2. Remove the terminal block cover from the AllSync IQ.
a. Remove screw from each side of the cover.
b. Lift the cover up off the unit.
3. Route signal circuit wires into the wiring compartment of the AllSync IQ.
1:49
FRI OCT 3 2014
:45
AM
American Time
800-328-8996
a. Remove knockout(s).
b. Use copper conductors only.
c. Use strain relief connector fittings in the knockout holes to secure the wires.
d. Route the wires into the wiring compartment, leaving enough slack to make all connections to the relay terminals.
4. Connect clock wires to the circuit relay terminals
H N
NO COM
CLOCK 1
NC NO COM
CLOCK 2
NC NO
BELL 1
COM NO
BELL 2
COM NO
BELL 3
COM NO
BELL 4
COM NO
BELL 5
COM NO
BELL 6
COM
Clock Circuit Terminals
Clock Circuit Fuses Surge Supression
ON/OFF Switches
See Appendix H on Page 50 for Clock Circuit Wiring Diagram
12
© American Time
1:49
FRI OCT 3 2014
American Time
800-328-8996
Adjust Time Menu
The Adjust Time menu serves two functions:
1. Manual correction of impulse secondary clocks, and
2. Simple synchronization of the AllSync IQ to an external time source.
u
9 to access the Adjust Time Menu v
1 to enter Adjust System Clocks Menu w
1 to bring up the Calculated Adjust screen
Enter the time shown on the secondary clocks (to the nearest
minute). The time entered should be in 12 hour format as AM/PM
settings are irrelevant.
O . The time difference between the secondary clocks and
the system controller is displayed.
O to initiate automatic correction of the secondary clocks
and return to the Adjust Time screen.
x
2 in the Adjust System Clocks menu (#3 at right) brings
up the Manual Adjust screen.
> repeatedly to correct impulse clocks manually.
when finished to return to the Adjust Time menu.
y
2 in the Adjust Time screen (#2 above) causes the unit to attempt synchronization with external time sources* in order of priority. If successful, a message confirming this flashes before the Time Display screen appears.
*The time sync priority can be configured. Reference Settings and
Configuration on Page 33.
2
Adjust Time
Choose:
1=Adjust System Clks
2=Ethernet Sync Now
3
Adjust System Clocks
1=Calculated Adjust
2=Man. Adjust Impulse
0=Cancel
3a
4
Calc Clock Adjust
Enter Time Shown on secondary clocks
00:00
Adjust System Clocks
Manual Adj. Impulsed
>=Advance Clocks
(1 per min) OK=Done
© American Time
13
advertisement
Related manuals
advertisement
Table of contents
- 4 Introduction
- 10 Ethernet Installation
- 12 Wired Clock Circuit Option
- 14 Wired Signal Circuit Installation
- 15 Wired Signal Circuit Programming
- 24 Remote Connect Web Interface-10 pages
- 32 Settings & Configurations
- 38 Troubleshooting Wired Clock Circuit
- 37 Troubleshooting Remote Connect
- 35 Troubleshooting GPS
- 41 Appendix A: Ethernet Timekeeping
- 44 Appendix D: Wired Signal Circuit Programming Examples
- 47 Appendix E: Checking IQ System Controller Status Information
- 48 Appendix H: Maintenance Guide
- 50 Appendix I: Clock Circuit Wiring Diagrams-5 pages
- 56 Glossary