advertisement
8-21. Error Messages
The FGX-2220 has a number of specific error codes. Use the SYSTem:ERRor command to recall the error codes. For more information regarding the error queue.
8-21-1.Command Error Codes
-101 Invalid character
An invalid character was used in the command string. Example:
#, $, %.
-102 Syntax error
SOURce1:AM:DEPTh MIN%
Invalid syntax was used in the command string. Example: An unexpected character may have been encountered, like an unexpected space.
SOURce1:APPL:SQUare , 1
-103 Invalid separator
An invalid separator was used in the command string. Example: a space, comma or colon was incorrectly used.
APPL:SIN 1 1000 OR SOURce1:APPL:SQUare
-108 Parameter not allowed
The command received more parameters than were expected.
Example: An extra (not needed) parameter was added to a command
SOURce1:APPL? 10
-109 Missing parameter
The command received less parameters than expected.
Example: A required parameter was omitted.
SOURce1:APPL:SQUare .
-112 Program mnemonic too long
A command header contains more than 12 characters:
OUTP:SYNCHRONIZATION ON
-113 Undefined header
An undefined header was encountered. The header is syntactically correct. Example: the header contains a character mistake.
SOUR1:AMM:DEPT MIN
-123 Exponent too large
Numeric exponent exceeds 32,000. Example:
SOURce[1|2]:BURSt:NCYCles 1E34000
-124 Too many digits
The mantissa (excluding leading 0’s) contains more than 255 digits.
-128 Numeric data not allowed
An unexpected numeric character was received in the command. Example: a numeric parameter is used instead of a character string.
SOURce1:BURSt:MODE 123
198
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 14 1 GETTING STARTED
- 15 1-2. Panel Overview
- 19 1-3. Setting Up the function Generator
- 20 2. QUICK REFERENCE
- 20 2-1. How to use the Digital Inputs
- 21 2-2. How to use the Help Menu
- 22 2-3. Selecting a Waveform
- 22 2-3-1. Square Wave
- 23 2-3-2. Ramp Wave
- 23 2-3-3. Sine Wave
- 23 2-4. Modulation
- 23 2-4-1. AM
- 24 2-4-2. FM
- 24 2-4-3. FSK Modulation
- 25 2-4-4. PM Modulation
- 26 2-4-5. SUM Modulation
- 26 2-5. Sweep
- 27 2-6. Burst
- 28 2-7. ARB
- 28 –Add Built-In Waveform
- 28 2-7-2. ARB- Add Point
- 28 2-7-3. ARB- Add Line
- 29 – Output Section
- 29 2-8. Utility Menu
- 29 2-8-1. Save
- 30 2-8-2. Recall
- 30 2-9. Frequency Counter
- 30 2-9-1. Frequency Counter
- 30 2-10. Coupling
- 30 2-10-1. Frequency Coupling
- 31 2-10-2. Amplitude Coupling
- 31 2-11. Tracking
- 32 2-12. Menu Tree
- 32 2-12-1. Waveform
- 32 2-12-2. ARB-Display
- 33 2-12-3. ARB-Edit
- 33 2-12-4. ARB- Built In
- 34 2-12-5. ARB-Save
- 34 2-12-6. ARB-Load
- 35 2-12-7. ARB-Output
- 35 2-12-8. MOD
- 36 2-12-9. SWEEP
- 36 2-12-10. SWEEP- More
- 37 2-12-11. Burst- N Cycle
- 37 – Gate
- 38 2-12-13. UTIL
- 38 2-12-14. CH1/CH
- 38 2-13. Default Settings
- 40 3. OPERATION
- 40 3-1. Select a Waveform
- 40 3-1-1. Sine Wave
- 40 3-1-2. Square Wave
- 41 3-1-3. Setting the Pulse Width
- 43 3-1-4. Setting a Ramp Waveform
- 44 3-1-5. Selecting a Noise Waveform
- 45 3-1-6.Setting the Frequency
- 46 3-1-7. Setting the Amplitude
- 47 3-1-8. Setting the DC Offset
- 48 4. MODULATION
- 48 4-1. Amplitude Modulation (AM)
- 49 4-1-1. Selecting AM Modulation
- 49 4-1-2. AM Carrier Shape
- 50 4-1-3. Carrier Frequency
- 51 4-1-4. Modulating Wave Shape
- 52 4-1-5. AM Frequency
- 53 4-1-6. Modulation Depth
- 54 4-1-7. Selecting the (AM) Modulation Source
- 55 4-2. Frequency Modulation (FM)
- 56 4-2-1. Selecting Frequency Modulation (FM)
- 56 4-2-2. FMCarrier Shape
- 56 4-2-3. FM Carrier Frequency
- 58 4-2-4. FM Wave Shape
- 59 4-2-5. FM Frequency
- 60 4-2-6. Frequency Deviation
- 61 4-2-7. Selecting (FM) Modulation Source
- 62 4-3. Frequency Shift Keying (FSK) Modulation
- 63 4-3-1. Selecting FSK Modulation
- 63 4-3-2. FSK Carrier Shape
- 63 4-3-3. FSK Carrier Frequency
- 64 4-3-4. FSK Hop Frequency
- 66 4-3-5. FSK Rate
- 67 4-3-6. FSK Source
- 68 4-4. Phase Modulation (PM)
- 68 4-4-1. Selecting Phase Modulation (PM)
- 69 4-4-2. PM Carrier Waveform
- 69 4-4-3. PM Carrier Frequency
- 70 4-4-4. PM Wave Shape
- 71 4-4-5. PM Frequency
- 72 4-4-6. Phase Deviation
- 73 4-4-7. Select the PM Source
- 74 4-5. SUM modulation
- 74 4-5-1. Selecting SUM modulation
- 75 4-5-2. SUM Carrier Waveform
- 75 4-5-3. SUM Carrier Frequency
- 76 4-5-4. SUM Waveform
- 77 4-5-5. Modulating Waveform Frequency
- 78 4-5-6. SUM Amplitude
- 79 4-5-7. Select the SUM Amplitude Source
- 80 4-6. Frequency Sweep
- 81 4-6-1. Selecting Sweep Mode
- 81 4-6-2. Setting Start and Stop Frequency
- 82 4-6-3. Center Frequency and Span
- 84 4-6-4. Sweep Mode
- 85 4-6-5. Sweep Time
- 86 4-6-6. Marker Frequency
- 87 4-6-7. Sweep Trigger Source
- 88 4-7. Burst Mode
- 88 4-7-1. Selecting Burst Mode
- 89 4-7-2. Burst Modes
- 89 4-7-3. Burst Frequency
- 90 4-7-4. Burst Cycle/Burst Count
- 92 4-7-5. Infinite Burst Count
- 92 4-7-6. Burst Period
- 93 4-7-7. Burst Phase
- 95 4-7-8. Burst Trigger Source
- 96 4-7-9. Burst Delay
- 97 4-7-10. Burst Trigger Output
- 99 5. SECONDARY SYSTEM FUNCTION SETTINGS
- 99 5-1. Save and Recall
- 102 5-2. System and Settings
- 102 5-2-1. Viewing and Updating the Firmware
- 102 5-2-2. Setting the Buzzer Sound
- 103 5-2-3. Frequency Counter
- 104 5-3. Dual channel Settings
- 104 5-3-1. Frequency Coupling
- 105 5-3-2. Amplitude Coupling
- 106 5-3-3. Tracking
- 107 6. CHANNEL SETTINGS
- 107 6-1. Output Impedance
- 108 6-2. Selecting the Output Phase
- 109 6-3. Synchronizing the Phase
- 109 6-4. DSO Link
- 111 7. ARBITRARY WAVEFORMS
- 111 7-1. Inserting Built-In Waveforms
- 111 7-1-1. Create an AbsAtan Waveform
- 112 7-1-2. Built-in Waveform
- 113 7-2. Display an Arbitrary Waveform
- 113 7-2-1. Set the Horizontal Display Range
- 114 7-2-2. Set the Vertical Display Properties
- 116 7-2-3. Page Navigation (Back Page)
- 117 7-2-4. Page Navigation (Next Page)
- 119 7-2-5. Display
- 119 7-3. Editing an Arbitrary Wavefrom
- 119 7-3-1. Adding a Point to an Arbitrary Waveform
- 121 7-3-2. Adding a Line to an Arbitrary Waveform
- 123 7-3-3. Copy a Waveform
- 124 7-3-4. Clear the Waveform
- 126 7-3-5.ARB Protection
- 128 7-4.Ouput an Arbitrary Waveform
- 128 7-4-1. Ouput Arbitrary Waveform
- 129 7-5. Saving/Loading an Arbitrary Waveform
- 129 7-5-1. Saving a Waveform to Internal Memory
- 131 7-5-2. Saving a Waveform to USB Memory
- 133 7-5-3. Load a Waveform from Internal Memory
- 135 7-5-4. Load a Waveform from USB
- 138 8. REMOTE INTERFACE
- 138 8-1. Establishing a Remote Connection
- 138 8-1-1. Configure USB interface
- 138 8-1-2. Remote control terminal connection
- 139 8-1-3. Command Syntax
- 143 8-2. Command List
- 146 8-3. System Commands
- 146 8-3-1. SYSTem:ERRor?
- 146 8-3-2. *IDN?
- 146 8-3-3. *RST
- 147 8-3-4. SYSTem:VERSion?
- 147 8-3-5. *OPC
- 148 8-3-6. *OPC?
- 148 8-4. Status Register Commands
- 148 8-4-1. *CLS
- 148 8-4-2. *ESE
- 149 8-4-3. *ESR?
- 149 8-4-4. *STB?
- 124 8-4-5. *SRE
- 124 8-5. System Remote Commands
- 124 8-5-1. SYSTem:LOCal
- 125 8-5-2. SYSTem:REMote
- 125 8-6. Apply Commands
- 126 8-6-1. SOURce[1|2]:APPLy:SINusoid
- 127 8-6-2. SOURce[1|2]:APPLy:SQUare
- 127 8-6-3. SOURce[1|2]:APPLy:RAMP
- 128 8-6-4. SOURce[1|2]:APPLy:PULSe
- 128 8-6-5. SOURce[1|2]:APPLy:NOISe
- 129 8-6-6. SOURce[1|2]:APPLy:USER
- 129 8-6-7. SOURce[1|2]:APPLy?
- 129 8-7. Output Commands
- 130 8-7-1. SOURce[1|2]:FUNCtion
- 131 8-7-2. SOURce[1|2]:FREQuency
- 132 8-7-3. SOURce[1|2]:AMPlitude
- 133 8-7-4. SOURce[1|2]:DCOffset
- 134 8-7-5. SOURce[1|2]:SQUare:DCYCle
- 134 8-7-6. SOURce[1|2]:RAMP:SYMMetry
- 135 8-7-7. OUTPut[1|2]
- 136 8-7-8. OUTPut[1|2]:LOAD
- 136 8-7-9. SOURce[1|2]:VOLTage:UNIT
- 137 8-8. Pulse Configuration Commands
- 137 8-8-1. SOURce[1|2]:PULSe:PERiod
- 138 8-8-2. SOURce[1|2]:PULSe:WIDTh
- 139 8-9. Amplitude Modulation (AM) Commands
- 139 8-9-1. AM Overview
- 140 8-9-2. SOURce[1|2]:AM:STATe
- 140 8-9-3. SOURce[1|2]:AM:SOURce
- 141 8-9-4. SOURce[1|2]:AM:INTernal:FUNCtion
- 141 8-9-5. SOURce[1|2]:AM:INTernal:FREQuency
- 142 8-9-6. SOURce[1|2]:AM:DEPTh
- 143 8-10. Frequency Modulation (FM) Commands
- 143 8-10-1. FM Overview
- 143 8-10-2. SOURce[1|2]:FM:STATe
- 144 8-10-3. SOURce[1|2]:FM:SOURce
- 144 8-10-4. SOURce[1|2]:FM:INTernal:FUNCtion
- 145 8-10-5. SOURce[1|2]:FM:INTernal:FREQuency
- 146 8-10-6. SOURce[1|2]:FM:DEViation
- 147 8-11. Frequency-Shift Keying (FSK) Commands
- 147 8-11-1. FSK Overview
- 147 8-11-2. SOURce[1|2]:FSKey:STATe
- 148 8-11-3. SOURce[1|2]:FSKey:SOURce
- 148 8-11-4. SOURce[1|2]:FSKey:FREQuency
- 143 8-11-5. SOURce[1|2]:FSKey:INTernal:RATE
- 144 8-12. Phase Modulation (PM)Commands
- 144 8-12-1. PM Overview
- 144 8-12-2. SOURce[1|2]:PM:STATe
- 145 8-12-3. SOURce[1|2]:PM:SOURce
- 145 8-12-4. SOURce[1|2]:PM:INTernal:FUNction
- 146 8-12-5. SOURce[1|2]:PM:INTernal:FREQuency
- 147 8-12-6. SOURce[1|2]:PM:DEViation
- 148 8-13. SUM Modulation (SUM) Commands
- 148 8-13-1. SUM Overview
- 148 8-13-2. SOURce[1|2]:SUM:STATe
- 149 8-13-3. SOURce[1|2]:SUM:SOURce
- 149 8-13-4. SOURce[1|2]:SUM:INTernal:FUNction
- 150 8-13-5.SOURce[1|2]:SUM:INTernal:FREQuency
- 150 8-13-6. SOURce[1|2]:SUM:AMPL
- 152 8-14. Frequency Sweep Commands
- 152 8-14-1. Sweep Overview
- 153 8-14-2. SOURce[1|2]:SWEep:STATe
- 153 8-14-3. SOURce[1|2]:FREQuency:STARt
- 154 8-14-4. SOURce[1|2]:FREQuency:STOP
- 154 8-14-5. SOURce[1|2]:FREQuency:CENTer
- 155 8-14-6. SOURce[1|2]:FREQuency:SPAN
- 156 8-14-7. SOURce[1|2]:SWEep:SPACing
- 156 8-14-8. SOURce[1|2]:SWEep:TIME
- 157 8-14-9. SOURce[1|2]:SWEep:SOURce
- 158 8-14-10. SOURce[1|2]:MARKer:FREQuency
- 158 8-14-11. SOURce[1|2]:MARKer
- 159 8-15. Burst Mode Commands
- 159 8-15-1. Burst Mode Overview
- 160 8-15-2. SOURce[1|2]:BURSt:STATe
- 161 8-15-3. SOURce[1|2]:BURSt:MODE
- 161 8-15-4. SOURce[1|2]:BURSt:NCYCles
- 162 8-15-5. SOURce[1|2]:BURSt:INTernal:PERiod
- 163 8-15-6. SOURce[1|2]:BURSt:PHASe
- 164 8-15-7. SOURce[1|2]:BURSt:TRIGger:SOURce
- 165 8-15-8. SOURce[1|2]:BURSt:TRIGger:DELay
- 165 8-15-9. SOURce[1|2]:BURSt:TRIGger:SLOPe
- 166 8-15-10. SOURce[1|2]:BURSt:GATE:POLarity
- 166 8-15-11. SOURce[1|2]:BURSt:OUTPut:TRIGger:SLOPe
- 167 8-15-12. OUTPut[1|2]:TRIGger
- 168 8-15-13. SOURce[1|2]:BURSt:TRIGger:MANual
- 168 8-16. Arbitrary Waveform Commands
- 168 8-16-1. Arbitrary Waveform Overview
- 169 8-16-2. SOURce[1|2]:FUNCtion USER
- 169 8-16-3. SOURce[1|2]:DATA:DAC
- 202 8-16-4. SOURce[1|2]:ARB:EDIT:COPY
- 202 8-16-5. SOURce[1|2]:ARB:EDIT:DELete
- 203 8-16-4. SOURce[1|2]:ARB:EDIT:DELete:ALL
- 203 8-16-7. SOURce[1|2]:ARB:EDIT:POINt
- 203 8-16-8. SOURce[1|2]:ARB:EDIT:LINE
- 204 8-16-9. SOURce[1|2]:ARB:EDIT:PROTect
- 204 8-16-10. SOURce[1|2]:ARB:EDIT:PROTect:ALL
- 204 8-16-11. SOURce[1|2]:ARB:EDIT:UNProtect
- 204 8-16-12. SOURce[1|2]:ARB:OUTPut
- 205 8-17. COUNTER Commands
- 205 8-17-1. COUNTER:STATE
- 205 8-17-2. COUNter:GATe
- 206 8-17-3. COUNter:VALue?
- 206 8-18. PHASE Commands
- 206 8-18-1. SOURce[1|2]:PHASe
- 207 8-18-2. SOURce[1|2]:PHASe:SYNChronize
- 207 8-19. COUPLE Commands
- 207 8-19-1.SOURce[1|2]:FREQuency:COUPle:MODE
- 207 8-19-2. SOURce[1|2]:FREQuency:COUPle:OFFSet
- 208 8-19-3. SOURce[1|2]:FREQuency:COUPle:RATio
- 208 8-19-4. SOURce[1|2]:AMPlitude:COUPle:STATe
- 209 8-19-5. SOURce[1|2]:TRACk
- 209 8-20. Save and Recall Commands
- 210 8-20-1. *SAV
- 210 8-20-2. *RCL
- 210 8-20-3. MEMory:STATe:DELete
- 210 8-20-4. MEMory:STATe:DELete ALL
- 211 8-21. Error Messages
- 211 8-21-1.Command Error Codes
- 212 8-21-2.Execution Errors
- 217 8-21-3.Query Errors
- 217 8-21-4.Arbitrary Waveform Errors
- 218 8-22. SCPI Status Register
- 218 8-22-1. Register types
- 219 8-22-2. FGX-2220 Status System
- 220 8-22-3. Questionable Status Register
- 220 8-22-4. Standard Event Status Registers
- 221 8-22-5. The Status Byte Register
- 222 8-22-6. Output Queue
- 222 8-22-7. Error Queue
- 223 9. APPDENIX
- 223 9-1. FGX-2220 Specifications
- 227 9-2. External Dimensions Figure