- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- NXP
- DEMO9S08JS16
- User Guide
advertisement
8.8.1
J30 - Buzzer enable jumper BUZ_EN
8.9
8.9.1
Enables Buzzer to be controlled by PTF4. This is the default setting.
Figure 8-21: Buzzer Enable Jumper Settings BUZ_EN (J30)
IIC Pull-up
The DEMOJM provides external pull-up resistors for SCL and SDA lines, enabled by installing the corresponding jumpers on J31. By default both jumpers are installed.
J31 - IIC Pullup Enable Jumpers IIC_EN
Enables IIC external pullup. This is the default setting.
Figure 8-22: IIC External Pullup Enable IIC_EN (J31)
8.10
8.10.1
Analog Input Potentiometer
The DEMOJM provides an easy access 10KOhm potentiometer whose output may be connected to PTD1 and/or PTB2, selectable by J32, POT_EN.
J32 - Potentiometer Output Selection Jumpers POT_EN
8.11
Selects the potentiometer output connection. By default they are both connected.
Figure 8-23: Potentiometer Output Selection Jumpers POT_EN (J32)
Optional Jumpers For Various VDD And VSS
The DEMOJM provides 5 jumpers, J22 through J26, for different VDD and
VSS connections on the bottom of the board. By default, they are not
36 DEMO9S08JS16 User Manual
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION
- 5 Overview
- 5 Package Contents
- 5 Supported Devices
- 5 Recommended Materials On The Getting Started DVD-ROM
- 6 Handling Precautions
- 6 HARDWARE FEATURES
- 6 DEMOJM Base Board Features
- 8 On-Board Logic Analyzer
- 8 On-Board Virtual USB Port
- 9 DEMO9S08JS16 Daughter Card Features
- 9 DEMOJM Board Jumper/Connector Quick Reference
- 12 Signal Mapping of DC9S08JS16 to MCU_PORT
- 13 GETTING STARTED WITH THE DEMO9S08JS
- 13 SYSTEM SETUP
- 13 Overview
- 14 Operating System Requirements
- 14 Software Setup
- 15 Quick Startup
- 15 Hardware Setup
- 19 OPERATING MODES
- 19 Overview
- 19 Debug Mode
- 20 Run Mode
- 20 External BDM Mode
- 20 P&E EMBEDDED MULTILINK TOOLKIT PC APPLICATIONS
- 20 Logic Analyzer Application
- 21 Terminal Application
- 22 DEMO9S08JS16 Unsecure Application
- 23 Accelerometer Demo Application
- 25 Serial Grapher Application
- 28 DEMONSTRATION MICROCONTROLLER APPLICATIONS
- 28 Logic Analyzer Application
- 28 Serial Accelerometer Application
- 29 JUMPER SETTINGS
- 29 System Power
- 29 Virtual Serial Port
- 30 CAN Port
- 31 Mini-USB Port
- 35 LED Display Port
- 35 Input and Reset Switches
- 37 3-Axis Accelerometer Jumper Settings
- 39 Buzzer
- 40 IIC Pull-up
- 40 Analog Input Potentiometer
- 40 Optional Jumpers For Various VDD And VSS
- 41 DEMO9S08JS16 CODE DEVELOPMENT SOFTWARE
- 41 Using CodeWarrior With The DEMO9S08JS
- 41 P&E Software Tools for HCS08 Microcontrollers
- 42 TRANSITIONING TO YOUR OWN TARGET
- 42 Hardware Solutions At A Glance
- 43 Working With P&E’s USB Multilink
- 44 Working With P&E’s Cyclone PRO
- 45 TROUBLESHOOTING
- 45 DEMOJM Board Is Undetected
- 46 CodeWarrior Installation Fails (WinDriver Error)