- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- NXP
- DEMO9S08JS16
- User Guide
advertisement
10.3.2
allows the on-board storage of multiple programming images. When connected to a PC for programming or loading it can communicate via the ethernet, USB, or serial interfaces.
Software
The Cyclone PRO comes with intuitive configuration software and interactive programming software, as well as easy to use automated control software.
The Cyclone PRO also functions as a full-featured debug interface, and is supported by Freescale’s CodeWarrior as well as development software from
P&E.
P&E’s Cyclone PRO is also available bundled with additional software as part of various Development Packages. In addition to the Cyclone PRO, these
Development Packages include in-circuit debugging software, flash programming software, a Windows IDE, and register file editor.
11 TROUBLESHOOTING
11.1
DEMOJM Board Is Undetected
Q: The connection assistant indicates that my DEMOJM board is undetected even though I have connected the hardware to my USB port. What should I do?
A: The connection assistant, which displays in either Codewarrior or P&E’s development software, is a dialog which allows the user to connect to the
DEMOJM hardware. If this dialog indicates that the DEMOJM hardware is not connected to the PC, the first step is to make sure that the DEMOJM hardware is connected to the PC via a USB 2.0 high-speed cable. If it is connected, unplug and then plug in the USB cable on the DEMOJM board and click refresh in the connection assistant. If the hardware still does not show up, try the following remedies:
(A) Re-Enable the USB driver
If you connected the DEMOJM interface prior to the installation of P&E’s
Embedded Multilink drivers, Windows will not have been able to find the appropriate driver and may have disabled the device. The DEMOJM board shows up in Window’s device manager as a “P&E Multilink,” since it contains
P&E’s Embedded Multilink circuitry. If you unplug and then plug in the device,
Windows will automatically disable it even if you have installed the drivers. To
DEMO9S08JS16 User Manual 41
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION
- 5 Overview
- 5 Package Contents
- 5 Supported Devices
- 5 Recommended Materials On The Getting Started DVD-ROM
- 6 Handling Precautions
- 6 HARDWARE FEATURES
- 6 DEMOJM Base Board Features
- 8 On-Board Logic Analyzer
- 8 On-Board Virtual USB Port
- 9 DEMO9S08JS16 Daughter Card Features
- 9 DEMOJM Board Jumper/Connector Quick Reference
- 12 Signal Mapping of DC9S08JS16 to MCU_PORT
- 13 GETTING STARTED WITH THE DEMO9S08JS
- 13 SYSTEM SETUP
- 13 Overview
- 14 Operating System Requirements
- 14 Software Setup
- 15 Quick Startup
- 15 Hardware Setup
- 19 OPERATING MODES
- 19 Overview
- 19 Debug Mode
- 20 Run Mode
- 20 External BDM Mode
- 20 P&E EMBEDDED MULTILINK TOOLKIT PC APPLICATIONS
- 20 Logic Analyzer Application
- 21 Terminal Application
- 22 DEMO9S08JS16 Unsecure Application
- 23 Accelerometer Demo Application
- 25 Serial Grapher Application
- 28 DEMONSTRATION MICROCONTROLLER APPLICATIONS
- 28 Logic Analyzer Application
- 28 Serial Accelerometer Application
- 29 JUMPER SETTINGS
- 29 System Power
- 29 Virtual Serial Port
- 30 CAN Port
- 31 Mini-USB Port
- 35 LED Display Port
- 35 Input and Reset Switches
- 37 3-Axis Accelerometer Jumper Settings
- 39 Buzzer
- 40 IIC Pull-up
- 40 Analog Input Potentiometer
- 40 Optional Jumpers For Various VDD And VSS
- 41 DEMO9S08JS16 CODE DEVELOPMENT SOFTWARE
- 41 Using CodeWarrior With The DEMO9S08JS
- 41 P&E Software Tools for HCS08 Microcontrollers
- 42 TRANSITIONING TO YOUR OWN TARGET
- 42 Hardware Solutions At A Glance
- 43 Working With P&E’s USB Multilink
- 44 Working With P&E’s Cyclone PRO
- 45 TROUBLESHOOTING
- 45 DEMOJM Board Is Undetected
- 46 CodeWarrior Installation Fails (WinDriver Error)