Important Safety Information. Greenlee H6510A Impact Wrench, H6510, H6510A

Impact Wrench

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards or unsafe practices which could result in an injury or property damage. The signal word, defined below, indicates the severity of the hazard. The message after the signal word provides information for preventing or avoiding the hazard.

Skin injection hazard:

Oil under pressure easily punctures skin causing serious injury, gangrene or death. If you are injured by escaping oil, seek medical attention immediately.

• Do not use fingers or hands to check for leaks.

• Do not hold hose or couplers while operating the power source.

• Depressurize the hydraulic system before servicing.

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

• Use accessories that are approved for impact use only. Accessories that are not approved for impact applications can break when used with impacttype tools.

• Inspect accessories before use. Discard accessories that have cracks, chips or gauges.

Failure to observe this warning could result in severe injury or death.

Electric shock hazard:

This tool is not insulated. When using this unit near energized electrical lines:

• Use only certified non-conductive hoses and proper personal protective equipment.

• Select and maintain the hydraulic fluid to meet the minimum dielectric standards required by your safety department.

Failure to observe this warning could result in severe injury or death.

Wear eye protection when operating or servicing this tool.

Failure to wear eye protection could result in serious eye injury from flying debris or hydraulic oil.

Greenlee / A Textron Company 3 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Impact Wrench

IMPORTANT SAFETY INFORMATION

• Keep all parts of the body away from rotating parts when the tool is in operation. Contact with moving parts can result in severe injury.

• Do not change accessories, inspect or clean tool when it is connected to a power source. Accidental start-up can result in serious injury.

• Maintain a firm grip on tool, using both hands at all times. Serious injury can result if an operator does not control the tool.

• Do not lock trigger in the power-ON position.

Operator can not stop tool when trigger is locked.

Failure to observe these warnings could result in severe injury or death.

Do not reverse hydraulic flow. Operation with hydraulic flow reversed can cause tool malfunction. Connect the supply (pressure) hose and return (tank) hose to the proper tool ports.

Failure to observe this warning could result in severe injury or death.

Tool and accessory may be hot during and after operation.

Contact with hot surfaces could result in serious injury.

• Wear protective gloves when handling, removing and installing drill bits. Drill bits can cut even when stationary.

• Inspect tool before use. Replace any worn or damaged parts. A damaged or improperly assembled tool can malfunction, injuring nearby personnel.

• Inspect the hydraulic hoses and couplings every operating day. Repair or replace if leakage, cracking, wear, or damage is evident. Damaged hoses or couplings can fail, resulting in injury or property damage.

• Use this tool for manufacturer’s intended use only.

Use other than that which is described in this manual could result in injury or property damage.

• Make sure all bystanders are clear of the work area when handling, starting, and operating the tool.

Nearby personnel can be injured by flying parts in the event of a tool malfunction.

Do not exceed the following hydraulic power source maximums:

• Hydraulic flow: 45.4 l/min (12 gpm)

• Pressure relief: 138 bar (2000 psi)

• Back pressure: 13.8 bar (200 psi)

Failure to observe this warning could result in severe injury or death.

Do not disconnect tool, hoses, or fittings while the tool is running or if the hydraulic fluid is hot.

Hot hydraulic fluid could cause serious burns.

Procedure for disconnecting hydraulic hoses, fittings or components:

1. Move the flow lever on the hydraulic power source to the OFF position.

2. Stop the power source.

3. Follow the sequence under Disconnecting

Hoses to prevent pressure buildup. In case some pressure has built up, loosen hoses, fittings or components slowly.

Note: Keep all decals clean and legible, and replace when necessary.

Greenlee / A Textron Company 4 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070