5 Mechanical module. Thermoplan fox2

The Thermoplan FOX2 is a coffee maker designed for commercial use. It features a touchscreen interface for easy operation, two bean hoppers for different coffee blends, and a built-in milk frother. The machine also includes a cleaning system to ensure optimal performance and hygiene.

PDF

Document

Technical manual

5 Mechanical module

5.1 Error messages mechanical module

Error no. / picture

TX0107

TX0113

TX0114

TX0115

TX0116

Piston error

Flow error

Overtime error

Text Cause

Bean hopper empty (left-hand side) - Bean hopper left is empty

- Lock of bean hopper is closed /

not connected

- After grinding, the brew cylinder

moves completely over the fix

piston (like in rinse).

- Grinder motor or starting

condenser is defective

- Grinder motor triac on power print

is defective.

Bean hopper empty (right-hand side)

- Brew cylinder cannot travel to

desired position

- The gear belt between motor and

drive screw of the brew cylinder

is defective or not mounted

- The way of the brew cylinder is

blocked

- The mobile piston is blocked and

the brew cylinder cannot travel

back to the micro switch

- The brew cylinder cannot travel

over the fix piston.

- Bean hopper right is empty

- Lock of bean hopper is closed /

not connected

- After grinding, the brew cylinder

moves completely over the fix

piston (like in rinse).

- Grinder motor or starting

condenser is defective

- Grinder motor triac on power print

is defective.

Too low water flow

Product is not dispensed correctly because of too low water flow

Fix

SECTION 6

- Refill coffee beans in left bean

hopper

- Check grinding position and

powder way

- Check if coffee beans are

grinded

- Check cable connections between

mechanical module - power print

and CPU.

- Check gear belt, gear belt plates

and voltage

- Try dispensing product again

- Perform a rinse

- Check mechanical module

- gear belt

- brew cylinder

- mobile piston

- micro switch

- fix piston

- Refill coffee beans in right bean

hopper

- Check grinding position and

powder way

- Check if coffee beans are

grinded

- Check cable connections between

mechanical module - power print

and CPU.

- Check gear belt, gear belt plates

and voltage

1. Open mains water connection

2. Empty grounds drawer

3. Perform rinse

4. Check flowmeter

5. Check pump

1. Dispense product again

2. Check flowmeter

3. Check pump

TX0119

TX0139

Powder error Grinders blocked 1. Empty grounds drawer +

vacuum-clean grinders

2. Perform rinse

3. Check mechanical module

Bean hopper missing or command unit open

Bean hopper is not mounted or the command desk is open

1. Place bean hopper correctly

2. Close command desk

3. Check contacts

REV-1 6.27

Technical manual

5 Mechanical module

5.1 Error messages mechanical module

Error no. / picture

TX0145

Text

Add coffee beans

Press ok to proceed product dispensing

Cause

Run out of beans during product dispensing

SECTION 6

Fix

Refill beans and confirm with OK button

TX0162 Error grinder right-hand side Grinder error right-hand side

TX0163 Error grinder left-hand side Grinder error left-hand side

1. Empty grounds drawer +

vacuum-clean grinders

2. Perform rinse

3. Check mechanical module

1. Empty grounds drawer +

vacuum-clean grinders

2. Perform rinse

3. Check mechanical module

REV-1 6.28

Key features

Touchscreen interface
Two bean hoppers
Built-in milk frother
Cleaning system

Frequently asked questions

Possible problems with the touchscreen include: slow reaction, flickering, missing product buttons, unreadable hieroglyphics instead of text, machine not starting completely, blue box with error message, black screen, or white screen.

To troubleshoot touchscreen problems, follow these steps: Switch off the machine, wait 10 seconds, switch it back on. If this doesn't fix it, remove the CF card, check for defects in the CF card slot, reinsert the card, and switch on the machine. If the problem persists, check the CF card type. Finally, check the LEDs on both the CPU and FOX-Print. If they don't blink, unplug the connection cable, control the contacts on both devices, plug the cable back in, and switch the machine on.

If the machine shows "Empty grounds drawer" error, the grounds drawer might be full, the magnet might be missing, the magnet switch might be defective, or the cable between the magnet switch and CPU might have a short circuit.