advertisement
6. Operation
EN
6.6 Switching the display between measuring inputs
The switching of measuring inputs changes between the display values of the measuring inputs and the display value of the arithmetic calculation. The display value of the arithmetic calculation is only displayed when this has been configured.
The following methods are supported:
Method
Static
Triggered
Cyclic
Description
A preset display value is shown for the duration of the trigger signal.
With each trigger pulse, the measuring input is switched further (series Ch1, Ch2, Ar).
The change is made cyclically over a preset time interval
(series Ch1, Ch2, Ar).
For the trigger signal, the multi-function button or the digital input can be used (for programming, see chapter 7.6 “Switching of measuring inputs”)
Before each change, the description of the measuring input is displayed.
■
■
■
Measuring input 1 = Ch1
Measuring input 2 = Ch2
Arithmetic calculation = Ar
24 WIKA operating instructions digital indicator, model DI35-D
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 2.1 Overview, version for panel mounting
- 8 2.2 Overview, version in desktop case
- 9 2.3 Description
- 9 2.4 Scope of delivery
- 10 3.1 Explanation of symbols
- 11 3.2 Intended use
- 11 3.3 Improper use
- 12 3.4 Personnel qualification
- 13 3.5 Labelling, safety marks
- 14 4.1 Transport
- 14 4.2 Packaging and storage
- 15 5.1 Requirements for the installation location
- 15 5.2 Mounting, version for panel mounting
- 16 5.3 Mounting, version in desktop case
- 16 5.4 Electrical connection
- 16 5.4.1 Notes on installation
- 17 5.4.2 Pin assignment, version for panel mounting
- 18 5.4.3 Pin assignment, version in desktop case
- 19 5.5 Interface connector
- 19 5.6 Switching on the digital indicator
- 20 5.7 Connection examples, version for panel mounting
- 22 6.1 Key functions
- 22 6.2 Accessing and exiting programming mode
- 23 6.3 Navigating in the menu
- 23 6.4 Changing numerical values
- 23 6.5 Accessing or clearing MIN/MAX values
- 24 6.6 Switching display between measuring inputs
- 25 7.1 Setting measuring inputs
- 25 7.1.1 Input signal
- 26 7.1.2 Start and end value
- 27 7.1.3 Number of decimal places
- 27 7.1.4 Offset adjustment
- 27 7.2 General settings
- 27 7.2.1 Default display
- 28 7.2.2 Switching of measuring inputs
- 29 7.2.3 Refresh rate
- 29 7.2.4 Measuring time
- 29 7.2.5 Display brightness
- 29 7.3 Arithmetic function
- 30 7.4 Setting the analogue output (option)
- 30 7.4.1 Start and end value
- 31 7.4.2 Reference value
- 31 7.4.3 Output signal
- 31 7.4.4 Example
- 32 7.5 Setting the serial interface (option)
- 33 7.6 Setting user authorisations
- 33 7.6.1 Authorisation levels
- 33 7.6.2 Cancelling the password protection
- 34 7.7 Setting special functions
- 34 7.7.1 Function of the digital input
- 34 7.7.2 Function of the multi-function key
- 34 7.7.3 TARE function
- 35 7.7.4 HOLD function
- 36 7.8 Setting switching outputs
- 36 7.8.1 Flashing display on reaching the switch points
- 36 7.8.2 Reference value
- 37 7.8.3 Switch points
- 37 7.8.4 Switch behaviour
- 42 7.9 Linearising sensors
- 44 7.10 Reading the serial number
- 44 7.11 Restoring factory settings
- 47 9.1 Maintenance
- 47 9.2 Cleaning
- 48 10.1 Dismounting, version for control panel
- 48 10.2 Return
- 48 10.3 Disposal