advertisement
EXTERNAL AUDIO AND VIDEO EQUIPMENT CONNECTION
You can connect outside signal source VCR VCD
DVD PC equipment to the TV set.
Antenna Input
1.Connect the VCR radio frequency input to
the back radio frequency input of the LCD.
2. Connect the antenna to VCR antenna input.
3. Press TV/AV button to select TV mode.
4. Press PLAY button in VCR to start watching.
AV input
1.Connect audio video output port in VCD to
AUDIO IN and VIDEO IN port in TV set.
2. Press TV/AV button to select composite
VIDEO mode.
3. Press PLAY button in VCD to start watching.
S-VIDEO input
If you use S terminal as signal input source, the image quality will be better than video(AV).
1.Connect S terminal output in DVD to S terminal
input in TV set.
2.Connect S terminal left/right audio output in DVD to
the relevant port in TV set.
3.Press TV/AV button repeatedly until the display
mode is S-VIDEO.
4.Press PLAY button in DVD to broadcast. At this time
the image programs in DVD will broadcast in TV set.
DTV input
1. Component terminal (Y/PbCb/PrCr) connect to the
component output of picture output device (such as
DVD, HDTV TUNER and so on ), the sound is input
from AUDIO IN:
2.Press TV/AV button to select HDTV mode.
3.Press PLAY button on the external device to start
watching.
HDMI input
1.Connect HDMI signal source output to the HDMI
input in this TV set.
2.Press TV/AV button to select HDMI mode.
3.Press PLAY button on the external device to start
watching.
19
A U D IO IN
VCD
S -V ID E O
IN
VIDEO IN
L R
AU D I O I N
ANT.
VCR
DVD
AUD I O I N
Y C b/Pb C r / P r
DVD
HDMI
DVD
S- V I D E O
IN
VIDEO IN
USING YOUR TV AS A COMPUTER DISPLAY
VGA input
1. Connect the VGA output port in the computer to the VGA port in the TV set.
2. Connect the audio cable in computer to VGA AUDIO IN port in TV set.
3. Press TV/AV button to select VGA mode.
4. Turning on the computer, the screen image of the computer will display on the
TV set.
At this time, the TV set can be used as a computer display.
VG A - AUDI O IN
VG A
RESOLUTION:
Mode
VGA
Resolution
640
x
480
Horizontal
Frequency
31.5kHz
SVGA 800
x
600 37.9kHz
XGA 1024
x
768 48.4kHz
Note: The above parameters are VESA standard.
Vertical
Frequency
60Hz
60Hz
60Hz
Note:
1. If the temperature of the TV set is rather low, it is normal that there may be some
artifacts when the set is first turned on.
2. Nonconforming pixels may occur on the panel, but they have no influence on the
normal function of the display.
3. In the standard operation, It is normal if there is one bright dot or dark dot on the
screen.
20
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- - Warning and caution
- - Buttons and interface position
- - Front control panel
- - Back interface
- - Wall mount switching support assembly instructions
- 1 Preparation for remote controller
- 2 Remote controller panel
- 3 Basic operation
- 3 Power on/off TV
- 3 TV program selection and volume adjustment
- 3 Recall
- 3 Mute function
- 3 OSD language selection
- 4 Screen display
- 5 TV program setting
- 5 Auto search
- 5 Manual search
- 6 Fine tune
- 6 Skip
- 7 Exchange
- 7 Image control
- 7 Set your favourite picture mode
- 7 Noise reduce
- 8 Picture mode /sound mode selection
- 8 Sound control
- 8 Sound effect control
- 8 System setting function
- 8 OSD background setting
- 9 Signal source setting
- 9 Screen display picture zoom setting
- 9 Other setting function
- 9 Sleep timer setting
- 10 PIP setting
- 10 Sound source setting
- 11 Color temperature
- 11 Digital filter setting
- 11 AAA setting
- 12 HDMI
- 11 External audio and video equipment connection
- 11 Using your TV as a computer display
- 12 Specifications