advertisement
INSTALLATION
Rigging
DANGER OF FIRE!
When installing the device, make sure there is no highly-inflammable material (decoration articles, etc.) within a distance of min. 0.5 m.
The device can be installed on the ground or on the wall or ceiling.
Hanging installation
The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for
1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
When rigging, derigging or servicing the device staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.
Procedure:
The device should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury and or damage to property.
The device has to be installed out of the reach of people.
The device must never be fixed swinging freely in the room.
Caution: Devices in hanging installations may cause severe injuries when crashing down! If you have doubts concerning the safety of a possible installation, do NOT install the device!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the device's weight.
The device must be installed in an absolutely horizontal position.
18/24 00072814.DOC, Version 1.0
advertisement
Related manuals
advertisement
Table of contents
- 3 EINFÜHRUNG
- 3 SICHERHEITSHINWEISE
- 5 BESTIMMUNGSGEMÄßE VERWENDUNG
- 6 GERÄTEBESCHREIBUNG
- 6 Features
- 6 Geräteübersicht
- 7 INSTALLATION
- 7 Montage
- 7 Hängende Installation
- 8 Traversenmontage
- 9 Anschluss an den DMX-512 Controller / Verbindung Gerät – Gerät
- 9 Master/Slave-Betrieb
- 10 Anschluss ans Netz
- 10 BEDIENUNG
- 10 Stand Alone-Betrieb
- 10 Control Board
- 11 DMX-gesteuerter Betrieb
- 11 Adressierung des Projektors
- 11 DMX-Protokoll
- 12 REINIGUNG UND WARTUNG
- 13 Sicherungswechsel
- 13 TECHNISCHE DATEN
- 14 INTRODUCTION
- 14 SAFETY INSTRUCTIONS
- 16 OPERATING DETERMINATIONS
- 17 DESCRIPTION OF THE DEVICE
- 17 Features
- 17 Overview
- 18 INSTALLATION
- 18 Rigging
- 18 Hanging installation
- 19 Mounting on a trussing system
- 19 DMX-512 connection / connection between fixtures
- 20 Master/Slave-Operation
- 20 Connection with the mains
- 20 OPERATION
- 21 Stand Alone operation
- 21 Control Board
- 21 DMX-controlled operation
- 21 Addressing
- 22 DMX-protocol
- 23 CLEANING AND MAINTENANCE
- 23 Replacing the fuse
- 24 TECHNICAL SPECIFICATIONS